What do I do if the leg keeps coming loose?Does that mean the bottom bracket is stripped or the bolt

For anyone who needs to replace the bearings - you will need 4 x LM30UU bearings for the machine.

Good video but there is a bit more you should do. There is a nut that holds that bolt in place on the inside of the clutch housing. When he takes the bolt out, the nut falls loose. You can see it in the video just as he removes the drive strap. It is the shiny item in the gap between the belt wheel and the clutch housing. While the strap may stay in place without the nut, you don't want to leave that nut floating around in that housing. It may interfere with the one way bearing or at a minimum clank around when you are using your rowing machine. To get in there and put the nut back on the belt or to clean the bearing, you need to remove the two phillips screws near the 4 mm drive belt bolt that was removed. Once those screws are out, you can take off the shaft cover that they held on. This cover may be stuck a bit. You can tap it lightly with a hammer. It takes a bit of force to remove it (it gets stuck), but the screws are all that hold it in place. Underneath you will find a retaining clamp. You will need a pair of special retaining clamp pliers to remove. I bought one for $15 at our local Farm & Fleet. Remove that clamp and the bearing plastic clutch housing will slide off exposing the bearing and the other side of the drive strap. You can now properly put the nut on the strap. Also a good idea to clean up the bearing and try to get some fresh automotive grease in there. I found the service people at Bodycraft are top notch folks. They are very kind and helpful.

The lat cable and the leg press cable on My XPress pro keep twisting bad, making the pulley housing to twist and be off centered - when I unscrew the cable at the weight stack, as soon as it completely unscrewed the cables twist and ravel so bad that the housing unit does 4 or 5 360° spins. Any suggestions?

If the top plate is off the weights which way do I move the wheels on the double pulley block?

Great tutorial 👍👍

I’m having issues while putting mine together. I’m on step 10 and the instructions say it should slide with one finger and mine only goes up since I connected the bolts on the first cables. I have to push the weight down pretty hard to slide down. Not sure what went wrong between step 6 and 7.

Box News, The crank arm is pressured on and the only way you can get it out is with the crank puller. You definitely have to put a little strength into it but it will come loose.

What do I do if the crank remover tool isn’t work and the arm is stuck.

Stoked I was able to find this post. My first time replacing a treadmills membrane. 🤞

Can you confirm if this is a brush/ brushless motor? Thank you.

Thank you

Thanks very much.

battery location for monitor

Appreciate it, have to move this for a client tomorrow. Nice simple Removal of the weights, has to come down two flights of stairs.

Is there bearing inside the cylinder or is the cylinder the entire bearing? And what is the name of the bearing so I can buy a replacement?

So is till like a Smith machine but the bar gives u a little more natural movement back and forth

so it appears that you removed the crank arm by removing a nut and using device to remove it ...my problem is that the shaft that is left at 2:23 actually broke off from riding the bike and now the tip is embedded on the crank arm which i can remove , what is the name of the part i need to replace like i mention at 2:23 the part i need replaced is exposed on the bike ...is it the axle ? thank you in advance....i have an echelon bike if that helps

Test 2

I'me having some issue with my brand new XFT. I did exactly like this video but the collumn stay stiff and doesn't move at all. Moving the chariot is a bit hard and I'm pretty sure there is an issue. other question is if we should lubricate the pulleys/cable or no.

QUESTION: I am looking to replace the left crank on a bike and got one that is a different weight than the original. The original crank is pretty heavy in comparison to my new one. Will this weight make a difference when riding the bike? Thank you for your video and look forward to your response!

pքɾօʍօʂʍ 😩

My VR200 lost all resistance on the pull stroke, but not all the time. The spring/clutch mechanism seems to retract the cord still but I fly backwards when I lose resistance. I think that’s probably not the spring clutch assembly but the, what I’m assuming, is some kind of pawl mechanism is the assembly with the belt in it? Any suggestions? Should I get part 136a or 139a on the parts list? When I hand rotate the assembly it seems to be fine and only allows for rotation in one direction as it should.

I have a VR400 and every couple of rows it doesn't catch and there's zero resistance on that row. Do you know of a fix?

mine bolts are on the front only on the back i have manual incline with plastic legs what to do then? if the floor is uneven can i put something?

Where do you get the parts from

What type of grease/lubricant should be used for the bearings please.

The lubricant must be *"PURE SILICON* with no additives in it. *_Otherwise it can destroy your walking belt!_* 👍

Very helpful, thanks! I need to do the same for the eddy mechanism for my ProForm 230U exercise bike. Where did you get the new bearings from?

Hello Bodycraft, I can't get a straight answer from anyone. I would like to run my Peloton app from my iPhone or iPad to the console. Is that even possible? If so, how could I do that? I purchased an adaptor from iPhone to HDMI but still not working.

Where do I buy the replacement cylinder?

What is the horsepower on the motor?

I'm interested too and would much appreciate the other assembly steps. Thank you

Make it cheaper and available in EU and you might get a lot of buyers.

Thank you so much for putting this together!

Good to know! Appreciate it.

Hi - Can you upload the other steps, please? This was useful. Thanks

Is the clutch mechanism so timid that we need to be very quiet while performing this repair?

How often should the Spacewalker belt be lubricated?

Thanks so much! This issue was really bugging me.

Hi there, thx 4 sharing. Sincerely hope u guys update the walking belt replacement etc. this type of treadmill really different from those in KZbin. TOTALLY DIFFERENT!!! Lol

Looks useful but no sound

Why they don't make it free spin when you stop pedaling?

What’s the purpose of this?

You shouldn't beat inner race of the bearing because you can cause balls damage. Proper approach is to push outer race using threaded rod with nuts and wide washers / old bearings or hydraulic press.

i have the 800M it wont respond when i tried to start