Thanks for wasting people's time

lol did he ever fix it?

Only problem is it will only work in an ideal condition. More than likely,Bolts shear or break off at inaccessible areas

BS if it was that lose it wouldn't have snapped the head off trying to losen it in the first place 😂

Mine too…now😉‼️🫡

I have three in the exhaust to do, but they’re all about a half inch down in the hole. Not sure if I can use my welder for that one.

That’s if there is enough for washer to grab onto.

Worked great. Even with a cheap harbor freight stick welder. Thank you

Thank you!

Would this work for broken bleeder screws. My weld kept snapping off. But i never tried it with a washer

This is fake!! You can see the engine isn't moving when he revs it up!!!

I've looked up many helpful videos and appreciate the people who take the time to show different techniques it's always done on the bench though not in the vehicle

Once I have that measurement what do I do with it? Not being a ahole I’m really asking

if the bolt broke don't you think the poor at best weld will break? aren't you welding the bolt to the hole? One other guy talks about putting a copper sleeve in the hole first.

Thank you so much!

Apart from washer that's what I've done One stud so far ive welded 13 nuts on it Another stud so far 3 nuts Neither have come out yet Just snap off like a carrot Panel beater over 30 year's experience 180 amp welder Weld looks just like yours glowing orange Welder cranked up Alloy block Im letting it cool for a few mins Just snaps off Ive used this method lots Worked every time Apart from now

Would a 110 mig burn hot enough to weld a nut on?

Every place does it

All it’s for is to shut up people so u can’t complain but as we see here people will still complain

That works unless sized

Ye and thre stil ppl that think there recycling 😂😂

Same result at Panera Bread. They empty all three containers, compost, recycling, and landfill in the same trash bag to take it out to the dumpster.

Our MK7 do need head gaskets but I also have oil coming out the passenger side under oil filter and deep stick

Just seen a guy put copper tube in first to protect the threads. Looks like you pulled out the outer layer of threads too

It worked!! I was trying to remove a cross-head screw with messed up head from a Yamaha RD350 engine, and I used stick welding

“its left handed🤓” FINISH THE VIDEO HE DEADASS SAYS WHY HES DOING WHAT HES DOING 🥸great job btw mechanic to mechanic!:)

Its left hand thread. Wtf u doing

Lefty tightly for most tow hooks. Try again

Fun fact, a lot of cars dont include the tow hook anymore

Only named german companies lol😂

As a tow truck driver i dont recommend using those, when you have it sucked on the trailer it causes extreme pressure on the front suspension and not to mention those things strip out all the time cause they are aluminum

It will be towed alot vw garbage

Thats not a vag toweye

😂😂😂😂

You sound like your from americas communist hat; in that case all threads everywhere are buggered; keep twistin anyways! Good luck to ya bud

Every European 😅😂

Thanks for the video. It helped so much!

You probably thought you can unscrew the wheel bolt caps with a torx bit too 😂😂😂

It’s a left hand thread

Bro I watched like 5 videos with 40k+ likes and your helped way more!!

Worked great getting valve cover bolt out of 08 Dodge nitro. Gotta have the washer though.

All devices are set at 16:9 now a day's, and you record in portrait mode. I do not understand this.

Where can I buy that piece?

Where do you run your welding ground? Just on the frame or somewhere on the block?

Thanks bro!!

Thanks man, I shall keep this information for when the time comes

That was a quicker fix than i thought

Goes back to rattling again in no time though. I find that a small wooden wedge behind the metal tab helps.

Off the road. Now!

Just get some easy out