Can I know the fiberglass tensile test standard dimensions?
@theuniversalgripcompany2 ай бұрын
Yes the strand needs to be at least 18 in. long. Diameter can be anything, according to the product. If you have more questions about this test you can send us a message through our website.
@The3edzon2 ай бұрын
hi, excuse me, i´m working with additive manufacturing, this type of test is recommended to analysis shear?, im gonna work with ABS and PLA, thanks.
@theuniversalgripcompany2 ай бұрын
Yes ASTM D732 is the premier test for plastics shear strength. Very popular for sunglass manufacturers and companies making performance plastics. We sell alot of these fixtures for shear testing. We have in stock.
@catkin-v4q2 ай бұрын
what about when unopened?
@theuniversalgripcompany2 ай бұрын
I didn't want to get soda all over our machine but we do sell baths and containers for wet testing.
@literailly3 ай бұрын
How much?
@theuniversalgripcompany3 ай бұрын
@@literailly send us a msg through our website for pricing. I don't put out any public prices because they change over time (inflation).
@MustaphaCHLILAK3 ай бұрын
Supper
@李林-s2z3 ай бұрын
Can be connected to pneumatic tubing to make the introduction more complete
@theuniversalgripcompany3 ай бұрын
@@李林-s2z yes we have another video “How to Install an Air Hose into Pneumatic Grips.”
@deepikaravichandran30683 ай бұрын
How to calculate the shear strength here?
@theuniversalgripcompany3 ай бұрын
This one is pretty straight forward, you can just use the ultimate shear strength from your machine reading. And the sample is usually 1x1”. So it’s an easy calculation to get shear strength per square inch.
@alihassan-kp5qz3 ай бұрын
How much is the difference between tensile strength for specimen with holes and without holes?
@theuniversalgripcompany3 ай бұрын
Depends on the size of the hole but somewhere around 15-25% reduction in tensile strength.
@alihassan-kp5qz3 ай бұрын
@@theuniversalgripcompany Thanks for the answer
@BinoSatria4 ай бұрын
What type of material?
@theuniversalgripcompany4 ай бұрын
This one was a low-medium strength steel. For higher strength and hardened steels, we would recommend a different, more robust wedge grip.
@kocovnik21534 ай бұрын
Hello, I have a question. Do you have springs around bolts in the middle moving part ? Thx for answer.
@arumayroy5 ай бұрын
I required this grip in India
@arumayroy5 ай бұрын
I required this grip in India
@prashundwivedi38706 ай бұрын
Sir what is the sample size tear test please
@singhd58926 ай бұрын
Hi what is the grip gap to be set
@theuniversalgripcompany6 ай бұрын
100mm gauge length is usually appropriate but can also do 200mm
@RobertPaynter-r1u7 ай бұрын
I don't think that could be thought a good test. The break occurred at the stress concentration at the lower grip - there must be a better specimen design. The plot we saw on the monitor has very little to do with the material properties - more on the behaviour of the grips as they compress the specimen.
@muhammed59879 ай бұрын
Can u please tell me about gauge length marking
@pankajkuhite94609 ай бұрын
What is the procedure for explosive friction test
@rofiqroslee11 ай бұрын
Hi..can you help me? My graph does not appear during test..
@juanpablocarrasquilla444 Жыл бұрын
What is the speed of the upper head that compresses the spring?
@christophersmith2014 Жыл бұрын
What connection is this ?
@josephbohme7917 Жыл бұрын
Sure like to see a video but geeze what the hell. your music is too darn loud, ease up on the db<. no reason to be that high it is not info. To test a material and not affected by holding procedure make a much bigger piece and make a central diamenter perhaps only 1x1 vs a piece with two ends 2x2 so that the clamp or attachment does not weaken the test material
@MohanChaudhari-lu7ho Жыл бұрын
Can we add any light censor or metal censor instead of foot swich
@theuniversalgripcompany Жыл бұрын
Yes, its possible to add this on your own. The grips are normally open (there is a spring to expel out the air when there is no pressure.) You can add any type of control mechanism or sensor/switch on your own. When the grip gets the air pressure, it closes. We don't sell these but you can make it on your own, its not difficult.
@saradarsingbugale4141 Жыл бұрын
Cable thickness and length?
@MechanoMinds07 Жыл бұрын
how to do this test?
@theuniversalgripcompany Жыл бұрын
You load 1 sample into the fixture and then push down with the top of the machine. You want to rupture the sample and record the highest peak force measurement.
@ابراهيمباداود Жыл бұрын
How much for this? Including shipping to Saudi Arabia
@creation_kkp Жыл бұрын
Please reply the grip length distance?
@theuniversalgripcompany Жыл бұрын
I believe the starting grip length distance on this test is 4 inches of distance/separation. You can refer to the ASTM method to double check.
@diamanproses Жыл бұрын
How long supports span for d790 testing, 3.2 think, 12.7 wide, and 127 long. Thank you
@theuniversalgripcompany Жыл бұрын
Hi Rumah, yes its based on the thickness of the sample. I think these are the correct files for thickness 1mm sample. If your sample is thicker, everything else must be scaled up. Please check the ASTM document for more info. We can customize the fixture according to your specific needs.
@samias4052 Жыл бұрын
I need this program how can I get it
@theuniversalgripcompany Жыл бұрын
You have to purchase one of the Galdabini testing machines the software program only works on these type of machines.
@jamesngolo8796 Жыл бұрын
hello can you show me how to setup the test method
@gsancak Жыл бұрын
grand
@diljanmohmand8172 жыл бұрын
Greeting Sir, I would request to please run a simualtion on Izod Impact testing in abaqus with full geometry and Steps involved.
@dougwilliams442 жыл бұрын
Test PG Classic's Mopar belt PLEASE!! 🙏🙏
@reinimex49102 жыл бұрын
The fabric/tapes are slipping thru the grips. Thats exactly how you NOT make the test.
@gabeflannery97502 жыл бұрын
very satisfying
@MOHAMEDTOWFICA2 жыл бұрын
How much force needed to crush the 150mm can??
@dgeorgxxx2 жыл бұрын
not good gripping.... the sample is slipping enough at the beggining of test..
@yigitcan8246 күн бұрын
The decreasing attitude on the graph at the beginning happened because of that?
@raadabdulkhudhur37792 жыл бұрын
what are the specifications for tensile testing of steel hollow tubes?
@theuniversalgripcompany2 жыл бұрын
The material is usually tested as a bar. For type testing you can put steel mandrel in the end like a cork for a wine bottle. This makes it easier to pull. Tubes are not standard samples, only flat and round tensile bars according to the ASTM. Tubes can be different diameter and wall thickness so there is no standard tube size
@ismaildaoud63832 жыл бұрын
Can you please make a vidon for the test
@ianramsden15332 жыл бұрын
Awesome video. Thanks.
@ronaldbarrett15062 жыл бұрын
Bambpoly Green Technology looking at your equipment. Thanks.
@paulhetherington38542 жыл бұрын
< /_fnd tensile resistance in lap top monitor tubes 1'v --> 5''v charges parallel AVNgrn an rd tubes 3' ''' v vk charges / /_transfer freq structs in both as start file construction use cell phone params as Peahi Jaws vids / >
@paulhetherington38542 жыл бұрын
Hence; proved it, isn't a, heart beat!
@malikabdulkarim7912 жыл бұрын
Hollow cylindrical shape (pipe) can be tested by this standard ASTM D 695 ???
@ppa67633 жыл бұрын
Can we use pneumatic press to prepare tensile sample like this.. If yes what is the pressure required?
@frankfastforward3 жыл бұрын
Need at lead 10 ton to move this die and initiate the cutting action. This one is usually used in hydraulic press but can be used in pneumatic press also.