OutboardsandToys

Пікірлер

@yungskeet 6 күн бұрын

Nice little bug in there

@Travis3500 27 күн бұрын

Man been trying to rebuild my 7.5 for awhile now just took off the flywheel tonight after pulling it all day with barely any spark in the mfer I found the spark plug wire connecting to the electrical box is fried so I’m hoping that’s all it is 🙏

@thomasinnis2370 28 күн бұрын

Just going to ignore your torn float lid gasket?

@rafawojtaszczyk1409 Ай бұрын

what fuel mixture for this engine is 1:100 or 1:50

@JuanGonzalez-ux5ey Ай бұрын

Thanks brotha great video

@johnnylawrence Ай бұрын

Your bowl is missing the gasket that sits on the bottom of the bowl.

@outboardsandtoys8413 Ай бұрын

This motor is still running great today

@johnnylawrence Ай бұрын

@@outboardsandtoys8413 great to hear! I got a 9.9 evinrude from 1992. Had the worst time trying to get it to run. I rebuilt the carb 3x over, new plugs, wires, ignition coils, power pack, fuel pump, water pump, thermostat, took the block out and replaced all major gaskets and still wouldnt fire/hold idle. I ended up using pb blaster small engine tune up, and bam, now runs great. All that work and it was gummed/carboned up.

@1skinnypuppy Ай бұрын

Super good job buds. That's some reality right there. I sure appreciate. BC Canada in the ocean. Thank you very much.

@7tosand Ай бұрын

I didn’t see any gaskets when you took the carb apart, or on the intake manifold. We’re there any gaskets?

@donk499 Ай бұрын

these were great engines, very smooth and powerful

@cruztraveler 2 ай бұрын

Is this efi?

@mikdav6734 2 ай бұрын

What. Did you use to remove and install those doors carb nuts. Such a pain in the ass

@antoniomoreno4899 2 ай бұрын

Hola buen dia tengo el mismo motor..arranca y cuando acelero el motor se para..como si se quedara sin combustible..el carburador esta perfecto..sera la bomba d nafta??? Me seria util una ayuda

@mikdav6734 2 ай бұрын

Great job on this video, good detail

@AAE-cg1il 3 ай бұрын

Great choice of music……

@sarahrobinson6409 3 ай бұрын

Great video thankyou! But I’m still having troubles…. Any ideas on the next troubleshooting check?

@mr.cryptobull1520 3 ай бұрын

Just bought a boat with this motor. Now I feel confident to do the carbs.. THANKS

@erikislas6734 3 ай бұрын

I just replaced thermostats and opened the heads to clean the passage lines and it's still peeing warm water.. 81 Johnson 140 V4

@StevenMyers-fu5pq 3 ай бұрын

What year is that motor

@donk499 Ай бұрын

1960

@larrythompson5617 4 ай бұрын

I really like how the carburetor comes off after removing the choke leaver. Easy peasy.

@Unkdrefinest 4 ай бұрын

Thanks for the video but can the thermostat keep the motor from Peeing? I've clean the pee hole and it still won't pee. Do you have any suggestions for me? Thanks

@saodykol 4 ай бұрын

Sounds nice, How fast. ,On mine 40 same year, 60hp carb, add timing,cup 17p got 35mph

@CTRadventures 4 ай бұрын

Thanks for this video! We just bought an 88 ranger 393v that came w a 6 cylinder 87 Johnson 150. The oil injectors removed to run 2 stroke. This is my first bass boat and power engine, so I'm trying to learn as much as possible. Again I'm completely new to motors, sometimes she seems she's a little rough on idle so I thought, hmm maybe the carbs need cleaned

@ChadCooper-13AquaFab 4 ай бұрын

Need a “how to” video Before i just start drilling 😅

@RichardGibson-kj5ov 4 ай бұрын

I just bought this same motor but it's missing the plate with the serial and model number. Do you have them on yours, I need to replace a few parts

@RichardGibson-kj5ov 4 ай бұрын

Do you have the model number for this, I think that I just bought the same one from fb market place and I need to replace a part., but I cant see any model numbers

@FishingwithFro 5 ай бұрын

I know this is an older video, but did you happen to know what year this motor was? I just picked up the same exact model yesterday and it needs a starter

@user-pt7qo1gd4t 5 ай бұрын

How many starts will you get out of this without the battery dying?

@lucatimer1234 5 ай бұрын

Hi...I have a question for you 😇 It's possible to modify a 9.9 Johnson (Year 2005) to 15 hp...?? I need a new carburettor, and what else..?? Thanks... E greetings from Italy..😇😃😉 (excuse my terrible english)

@Jaybundy47 5 ай бұрын

You wouldnt happen to have that bracket and recoil do ya? Need to do reverse of what you did. (going from starter to pull start) Great video!

@arrowheadhunter420 5 ай бұрын

Thanks man good video

@plcking23 6 ай бұрын

Very often we take youtube postings like this for granted. I have a 1993 15 HP Johnson, and I wanted to clean the carb. Your video enabled me to get at the carb in 5 minutes ! The little metal rod was the clincher ! Thank you very much !

@conraywest 7 ай бұрын

So does the water go through thermostat before it gets to tell tale? Why does it need to close? What is the negative of just removing it and having water flow around head at all times instead of only when thermostat opens?

@outboardsandtoys8413 7 ай бұрын

On a 2 stroke its ok to run without a thermostat and yes it will still pee it controls the water going through the jacket on the head u just cannot remove on a 4 stroke that has a computer the downfall is that it keeps the motor temp regulated for easier start-up during winter other than that u won't see any other changes other than motor running cooler

@user-ue6pv9dd4m 8 ай бұрын

Thanks for the video, I am working on the same motor, rubber tip is worn out, searched high and low for a carb rebuild kit. Thanks

@user-ue6pv9dd4m 8 ай бұрын

Thanks for the video, I have the same motor, I've searched far and wide for a carb rebuilt kit, can't find shit, rubber tip on needle is worn out. Thanks

@oldergeologist 8 ай бұрын

Very good description. My motor gives problems at the start of every season. Also the gear change lever breaks if you lay the motor down on that side. Will never buy another Mercury. Yamaha for ever.

@JamesJones-cx5pk 8 ай бұрын

Im glad to see that with 3 people. I just bought a 30 for my 16 V.

@smannee 7 ай бұрын

The 2 cylinder 30 is amazing, the 3 cylinder 30 is even better.

@joshua13js 9 ай бұрын

Is it easy to rebuild ?

@Travis3500 28 күн бұрын

Yes very lmao I can do it in probably 10 minutes

@joehozzy2616 9 ай бұрын

Very well explained. thank you.

@faronmastin8683 10 ай бұрын

Thanks for the video I just bought one for $50.00 with controls and a stand, He took the throttle actuator off of it for another outboard, it has 155 lbs of compression in both cylinders