Reclaim Filters & Systems Inc

Пікірлер

@philhoyle6330 4 күн бұрын

thanks bro a very clear explanation.

@RonnelGacutana 2 ай бұрын

can you adjust a 40 - 60 pressure switch to 10 - 30?

@reclaimfilterssystemsinc7529 2 ай бұрын

Hi Ronnel, short answer is no, you have a little adjustment each way, but they do make special pressure switches that operate on lower pressures but they are non standard and usually expensive. It's cheaper to run a 30/50 pressure switch and use a pressure reducing valve in order to obtain the pressure you want.

@sebastienmorand2479 3 ай бұрын

Well done. Explanations are crystal clean et visual.

@balkaranmahabir8557 3 ай бұрын

Very good explanation. My pump os only goin on n off every minete n ah half. Ag gonna dig intonit now !!

@walters2405 3 ай бұрын

Excellent video.

@jesusaguilar5708 5 ай бұрын

grate information sir

@cw3438 5 ай бұрын

Brilliant. The BEST explanation I've ever seen!

@nckeller 5 ай бұрын

Thank you, that is very kind.

@REJANOOP Ай бұрын

@@nckeller kzbin.info/www/bejne/mqncdqt4l7-pnLssi=63D_uB2rPjR1TfhO

@REJANOOP Ай бұрын

kzbin.info/www/bejne/mqncdqt4l7-pnLssi=63D_uB2rPjR1TfhO

@makenchips 7 ай бұрын

Excellent video on the subject well done explain it simply and succinctly.

@romnickgatab6184 8 ай бұрын

Clear explanation. Thank you so much.

@bcallahan3806 8 ай бұрын

Well done.

@cathy4209 9 ай бұрын

Finally a video that's to the point no extra blah blah blah to sit thru that only tends to confuse things. BTW I'm a 64yr.old widow of a wonder man who had a remodeling company. He was such a talented worker but not a great teacher. :)

@reclaimfilterssystemsinc7529 9 ай бұрын

Thank you, much appreciated. Glad to help. I've heard of wonder women but never a wonder man. Other than: "I wonder what that man is doing". Usually us guys are just OK at best... : )

@PelicEditz 9 ай бұрын

Hi. This is fantastic. Can you do one with a low pressure cut off too? I’m having some issues with the low pressure cutting off when I adjust this. They had said the cut off was just a few pounds below my cut in. That does not give much leeway.

@cayrick 9 ай бұрын

Have an on demand tankless water heater on a pump operated water system. Every time the pump cut in (20/40) the water heater would shut off ruining my shower. Followed your well done video and bumped up the pressure a few pounds and it silenced my bitchy wife. Thanks for you very well done video.

@reclaimfilterssystemsinc7529 9 ай бұрын

Glad to help. We have a tankless as well, and sometimes if the pressure isn't right you'll get a cold shower for a few seconds. It saves us a lot of money but it was finicky about pressure. We ended up installing a cycle stop valve and a larger ballast pressure tank to eliminate the pressure swings and now we have steady hot water. Hallelujah!

@cayrick 9 ай бұрын

since my last post I followed the video instructions and bumped up the cut in pressure from 20 to 24. This seemed to resolve my issue with a cranky wife taking cold showers. @@reclaimfilterssystemsinc7529

@saurabhyadav9172 10 ай бұрын

Hi sir i need some help 🙏🙏🙏..I am pump assembly machenical technician..

@saurabhyadav9172 10 ай бұрын

Can you help me

@nckeller 10 ай бұрын

How can I help

@saurabhyadav9172 10 ай бұрын

@joeycharm77 10 ай бұрын

nice

@Bravers Жыл бұрын

The best video in this topic for sure.

@reclaimfilterssystemsinc7529 Жыл бұрын

Thank you, much appreciated.

@marcelino1949 Жыл бұрын

Thanks sir

@anthonydiehlman5326 Жыл бұрын

I want to take a moment to thank you, FOR this video...💯. It was the ONE that HELPED me FIGURE out how to adjust my springs properly, AND LIKE A BOSS..👍😎.

@db8926 Жыл бұрын

Nice setup. Who makes the ion and ozone generator? Thanks

@139forLife Жыл бұрын

One of the best vids thank you

@unitedsoulwarriorsfreedom4313 Жыл бұрын

We’re not free, debt slaves through the legal fiction ALL CAPS … they attacked us in a different way, happy millions are awakened to this now. Much love.

@rukundojobson2249 Жыл бұрын

Well done. Thanks

@shank-bf3gu Жыл бұрын

By far the best explanation on how a pressure switch works. Thanks for sharing.

@REJANOOP Ай бұрын

kzbin.info/www/bejne/mqncdqt4l7-pnLssi=63D_uB2rPjR1TfhO

@markb8685 Жыл бұрын

this is the best how to video, perfect.

@nwced Жыл бұрын

I had a pressure box installed and the pump keeps starting every few seconds. The max is adjusted to 30lbs. Should I adjust the bigger screw counter clockwise or what would you suggest? This problem is driving me up the wall. I hope you may have a idea of how to fix the problem.

@Sharklicker2000 Жыл бұрын

So it's normal to have water in your gauge? Interesting. Thought that might have been a problem

@russkeller5747 Жыл бұрын

That's called a glycerin filled gauge. It's a stainless steel gauge filled with glycerin to prevent gauge bounce and vibration. If you've ever seen a gauge needle vibrate it's hard to make an accurate reading. Kind of a shock absorber for the needle and mechanism in the gauge.

@Sharklicker2000 Жыл бұрын

@@russkeller5747 thank you for the explanation, makes total sense.

@marshaosinski Жыл бұрын

P r o m o s m

@reclaimfilterssystemsinc7529 Жыл бұрын

I don’t have an ORP meter on the pool. The ozone generator is a 0-10 gram per hour, K1 unit. We usually run it at 5 to 6. The dial reads from 0 to 10 and corresponds linearly to the output.

@reversefulfillment9189 Жыл бұрын

No one has really gotten into the guts like you have. I'm working on mine, I get to 34 PSI and it doesn't cut off, it just sits there and the contacts never separate. Frustrating, but I think I'll have to get a new switch, it's about 20 years old. Any ideas? I cleaned the contacts and if I tap on the pipe below sometimes I can get it to disengage for a second. I was hoping it was something easier than replacing the switch but, that doesn't look too bad. Subscribed.

@russkeller5747 Жыл бұрын

At 34 PSI the contacts on a 30 to 50 or a 40/60 should be closed, energizing the pump so it keeps going to the cut off pressure of (50) or (60) psi. If the pump is not able to go higher than 34 psi there may be a pump issue or something is using water faster than the pump can push it. If you change the switch please make sure to cut power and drain water pressure first.

@Gpabatman Жыл бұрын

Is it safe to go higher on turn on turn off than 40/60.

@rickoddo9811 Жыл бұрын

no matter how much i tighten them down it doesnt do anything, we have very low water pressure here

@amgari007 Жыл бұрын

Thank you for the video. If I installed 30-50 switch, is is possible to lower the pressure and make it 25-45.

@rogerg4916 Жыл бұрын

Is there any harm in widening the differential to 30 lbs?

@reclaimfilterssystemsinc7529 Жыл бұрын

If the cut off only adjustment will go that high it will not hurt anything. I suppose you have a reason, but you are not doing the pump or water system any favors by having such a wide pressure sweep. Typically we adjust it up + 2 psi to give the pump a slightly longer run cycle and prevent the ON/OFF/ON/OFF cycling that could occur if the gap is too small, but widening it too much may result in a pump that never turns off or leaks from too much or too little pressure beyond the expected 30-50 or 40-60 psi.

@rogerg4916 Жыл бұрын

@@reclaimfilterssystemsinc7529 Yes, I can adjust it that high, probably more. I was thinking that it would give less frequent pump cycling. My concern was that it might overstretch the tank diaphragm and cause premature failure.

@nckeller Жыл бұрын

@@rogerg4916 A Ha!, Ok common problem when the tanks (pump tank A.K.A. ballast pressure tank) start to go bad. The air-bladder starts to fill with water or the pressure in the bladder is to low, or both. With ZERO water pressure the ballast tank air pressure should be 28 psi using a 30/50 pressure switch, or 38 on a 40/60 switch. It’s the pump switch cut-in pressure minus 2 psi.

@cliffhay3847 Жыл бұрын

my pressure switch has only one adjustment it is a sta rite pump how do both adjustments with just one place to adjust ?

@russkeller5747 Жыл бұрын

Hi Cliff: Sometimes smaller pumps with a built in pressure switch have just one adjustment for the range. It will be missing the cut off only adjustment. They seem to work OK and if you ever replace it you can install the better type with both. The Square D's are still OK but I really like the Merrill's Heavy Duty Standard no lead pressure switch. It has Allen key wire retainers and the contacts and contact plates are a bit beefier.

@noname-te4lh Жыл бұрын

as others have said, excellent video. much appreciated!

@tylerbouck3555 Жыл бұрын

Got it, haha. Thanks man!!

@ariesruswandi 2 жыл бұрын

Pls make content about AOP (advanced oxidation process)..thx

@ariesruswandi 2 жыл бұрын

can u share orrp level when ozone run..Thx

@georgegarner1775 2 жыл бұрын

Good video

@russkeller5747 2 жыл бұрын

Thank you George. It was something that confused me at first but once you do what's going on it's not so bad.

@aaronhenry9294 2 жыл бұрын

Thanks for the demonstration, very thorough. Good video 👍

@alexandruvoicu923 2 жыл бұрын

Man how Connect electric????

@reclaimfilterssystemsinc7529 2 жыл бұрын

Hi Alex I don't understand the question. Are you asking how much money an electrician or plumber would charge to install a pressure switch? If so I can tell you precisely. It's more than you think... Learn all you can. Be Safe and do it yourself. Make sure the power and water are OFF before you work on it.

@alexandruvoicu923 2 жыл бұрын

@@reclaimfilterssystemsinc7529 I managed to find its inputs and outputs, I tested it with the control lamp, it's simple! Thank you!

@rashellyohn5128 2 жыл бұрын

Thank you (911) Mother hen needs h20 for her chicks... Is there a way to do any adjustments without a working gauge on the pump or pressure tank. I bought the house and the pump was as is. The pump runs so far 20 min. and it never shut off. The pressure switch states that its calibrated at 30-50. I set the pressure , bladder tank at 28 psi with a pump. I don't know if the pressure switch is at the 30-50 factory settings. Is there a way to back out the screws and start over counting the turns. Or in a pinch get the pump to get water to the house. The pressure tank is empty and the pump just runs with out any water to house or well/trol pressure tank> Any help is appreciated.

@andrewholt8760 2 жыл бұрын

Great easy to understand and clear explanation, got the where flowing again thanks

@reclaimfilterssystemsinc7529 2 жыл бұрын

In Bar it’s 0.138 less that the on pressure. For example: That’s 2 psi under cut in, so for a 40/60 switch the pressure in the tank “dry” with zero pressure on the system and the pump off is 38 psi. Cut in 40 less 2 psi equals 38 psi. If the pressure is too high you may get water hammer, if too low then your pressure could drop suddenly when to use water and could cause an on/off/on/off… cycling of the switch which could ruin a pump motor.

@JasonVladimir 2 жыл бұрын

Great video! Thanks for sharing!

@osamagad1710 2 жыл бұрын

kzbin.info/www/bejne/g56bd3V-iM53odU What is the pressure switch is used in this machine?

@reclaimfilterssystemsinc7529 2 жыл бұрын

Looks like a simple demand switch. When the nozzle opens and the pressure in the system drops it’s contacts open or close doing something like maybe mixing the aggregate. The type of switch depends on the pressure used. Once you know the supply pressure and the pressure drop when the nozzle is opened you can go to Grainger or McMaster Carr and look-up an appropriate switch to handle the load.

@briancaine9130 2 жыл бұрын

This was excellent. The psi graphic on the left made all the difference. Thanks.

@roberthughes5169 2 жыл бұрын

In ground well pump ajustment

@anxietychannel 2 жыл бұрын

Thank you...what if my pressure goes to zero and the switchch on...what to do now?

@russkeller5747 2 жыл бұрын

If the contacts are closed and you have no pressure you start with (assuming you know how to use a multimeter) check power on both sides of the switch. Here in the U.S. it's usually 230VAC. If you have power and no water, you may have a bad pump. Lastly sometimes gauges go bad and can read zero but you can still have pressure. If all else fails, call a well driller or plumber in your area and they'll get it straight. Good luck

Ең жақсы KZbin

Пікірлер