[thank, you for youre video. nice looking dump truck. i, bought a 1973, Ford F-700 Dump truck. 361 engine. 5-spd. manuel trans. 2-spd. rear axle. air brakes]
@keithford95644 күн бұрын
You got a good one I've got a 1975 f700 just me five cent's worth change the 10.0 20's and find you some adapter for 11R22.5 cheeper to find those tires and it ride a little better handle a load alot better if you plan on keeping it. Good looking truck!!
@joesayles79536 күн бұрын
I appreciate you making this video 6 years later and still helping guys like me out!
@TheFSeries17 сағат бұрын
That’s what it’s for! Thanks for watching!
@user-ed1ln7un6n6 күн бұрын
Necesito una de caregato
@jadenvoshall11737 күн бұрын
How long did it take you to rebuild it and put everything back together
@cycribbs8 күн бұрын
So in layman terms tighten to 90 NM, what is NM, 66 lb per foot loose in one complete turn, so you tighten up the bolt and then you loosen it one whole turn and then tighten to 47 to 53 NM, as I said what is NM and then 35/90 LB / ft, and then tighten an additional 85 90°, explain that a little easier for someone who's not used to doing this type of work but can't afford to have anybody do it for me please
@danapetersen75119 күн бұрын
I have a 1994 F-350 with a Chinook Class C on the back. The front Caliper and hub assembly include a gear like fitting on the back of the hub and the nuts are on the under side of the ABS sensor gear. Do you know how the sensor gear is placed on the back of the hub and how it is removed?
@Pontiacdreams9 күн бұрын
This really! Helped. THANK YOU- I was getting ready to use the Dremel ….
@pitbikesforlife152811 күн бұрын
Thank you so much man you help me
@RigginJiggin12 күн бұрын
Would 9th gen taillights fit on an 8th gen?
@TheFSeries11 күн бұрын
Yes The taillights physically fit interchangeably from 80-96 However, 1980-86 has different bulb pigtails
@guillermoorozco499413 күн бұрын
What radiator is that ?
@TheFSeries11 күн бұрын
Champion 4 row aluminum Have had 2 and both developed the same pinhole
@guillermoorozco49946 күн бұрын
@@TheFSeries so would u recommend it or no ?
@TheFSeriesКүн бұрын
@@guillermoorozco4994 if you can get it to not pop a hole, 100% recommend. But due to it being replaced, save up and just have a brass OEM unit redone
@aaronelliott501916 күн бұрын
Thank you for the video. Was this a powerstroke or idi?
@TheFSeries15 күн бұрын
IDI truck using a 1997 Powerstroke ZF5 😂
@aaronelliott501915 күн бұрын
@@TheFSeriesI am putting a zf5 47 into my IDI right now! Awesome thanks again.
@josesmoya18 күн бұрын
Question do you can do a video explaining about the 12 pin harness that usualy is smoked on my idi . I just tryng replace it. Thanks in avance.
@josesmoya18 күн бұрын
Thanks bro .ill go to order it . Good job
@josesmoya18 күн бұрын
Thanks bro .ill go to order it . Good job
@Dan-y8m18 күн бұрын
Listen to her purrrrr😊❤
@garymahon195519 күн бұрын
My 83 f150 8s not charging at all . I put new alt and volt reg on, and looked at wiring and seems ok, so it must be a ground problem or voltage leak. I may try what you did,but mine doesnt have an alt bracket really.
@rodneymoore348519 күн бұрын
I used my credit card.
@WilliamMunny-d8s19 күн бұрын
shouldnt there be a big sock on the end of the pickup tube? ive never seen just bare metal tube like that
@Creationadmiration23 күн бұрын
Got me a 1973 f600 with a mini ox body style dump beds its cool as hell
@alexandermadrigal3465Ай бұрын
Do you know if you can put regular rotors on this spindle without the spacer ?
@user-mw1ge8mi3rАй бұрын
Hello Sir, I have a 1990 ford f250, with a 5.8 L engine. When I turn my wiper control knob on, my motor doesn't work and I get a lot of static sound and my battery gauge needle starts bouncing around. Do you think it may be some sort of short in the switch mechanism, or the actual wiper motor? Thanks, Grandpa
@TheFSeriesАй бұрын
Sound like the motor itself is bad or failed to a point it tries to move but cant
@itspitbull0196Ай бұрын
Great video hope my 90 isn’t terrible I’m really not trying to lift the engine any
@fitstudboiАй бұрын
Watched all the way great...very detailed except the reason i came was how to remove tbe tail light/housing without damaging it. I cannot get it off aside from the two screws i took out intutually which frees up one side. If ita a clup system uts not unclipping if there is a move and push and pull a certain way what may that be? Its a 1994 ford f 150 xlt
@TheFSeriesАй бұрын
Just 4 screws 2 outside, 2 inside (facing the tailgate when it is closed)
@fitstudboiАй бұрын
@@TheFSeries thank you I realised there was a stick on grill looking design over the lights that covered the two outer screws ugh!..I almost broke the thing till finally I realized that maybe that grill cover is not original to the tail light and nope! The double sided black foam tape was what held that on for years.. thank you so much yes.. thank you for the help. If I hadn't figure out the stuck on grill, your response would have reinforced and help me solve the issue..I thought all this time over 12 years that those tail lights were custom tail lights that came looking like that 🤣🤣🤣🤣
@caydenplaysyt5274Ай бұрын
Step one take it out
@barbarajones2620Ай бұрын
Can you run a hot wire to the switch that turns the tanks and it work but it won’t work once you take the hot wire off of it is the switch bad or good
@TheFSeriesАй бұрын
Is there 12v already being supplied? If so, the switch is bad. However I had a switch to work; but the clip break and the wire slip off
@barbarajones2620Ай бұрын
There’s no power getting to the switch! He can run a hot wire and the pumps come on !
@TheFSeriesАй бұрын
@@barbarajones2620 then you need to trace that wire to figure out what it going on. What color is the wire in question?
@coast2coaststudiosАй бұрын
you fixing this baby on the side of a highway or something?
@TheFSeriesАй бұрын
No, why?
@TheDariusBlaze13 күн бұрын
@@TheFSeriesthe traffic but It’s not bothering me
@stevenmorris2293Ай бұрын
Thanks. I also like your battery strap. Ill use that too .
@luckyred1818Ай бұрын
Transfer case
@joshmccue9534Ай бұрын
I know this is an old video I’m just posting this in the hopes it helps someone out but I found wrapping a hammer in a microfiber and tapping in the crank seal works best
@TheFSeriesАй бұрын
That definitely would work
@johnbridges92642 ай бұрын
What a bunch of BS, left out how they attach to controller, That’s a hard fail for me!
@TheFSeriesАй бұрын
I mean, they attach exactly how the old ones came off.
@caden2152 ай бұрын
video was made 4 years ago just got the same exact part from carquest they charged me $80 wish it was $20 like he said
@TheFSeries2 ай бұрын
Holy crap Yayyy Covid prices!
@Andre-gt3ip2 ай бұрын
Can this tank work for gas engine?
@WillKlaver2 ай бұрын
.. those pressure switches are different also, gotta change That .. ❄️🥶🌬️
@philiphapeshis12262 ай бұрын
Glow plug controller?
@jimwallace40452 ай бұрын
I believe I could get along with that feller.
@alex5.4382 ай бұрын
This literally saved my life was already stressing thank you so much
@TheFSeries2 ай бұрын
Glad to help
@reboundish2 ай бұрын
Thanks for sharing! Hope they work, time will tell? just ordered a set! Looks like you ran out of yellow paint?
@soheilsoheili97992 ай бұрын
Sir ,thank for the video do you have the part number for this soiliod?? I am unable to find it ,if you could let me know please
@seetheforest2 ай бұрын
Another Ford nightmare idea. The worst way to attach and remove a pulley in the history of the world.
@seetheforest2 ай бұрын
Voltage is nothing without solid grounds. Multiple grounds. Everything needs grounded. Distributor,coil,EGM, ICM, body.
@MXNDAE2 ай бұрын
Thanks for this video. I kinda like the design and kinda don't. I think the synergy ones look way better with the longer body for more stability but theyre discontinued.
@pivotmaster95562 ай бұрын
Funny thing is electrons are actually flowing from ground to positive. Good job this helps a ton though with a good connection
@jameslaiola49763 ай бұрын
Thats what im lookin for Sir. Can i ask if you have any available partnumbers? I want to do the same thing
@robertyeary55313 ай бұрын
I have a 96 f150 duel tanks. I got a new pump and tank in the front. I almost have a full tank and I was using the back tank. I flipped the switch to the front tank and it fires up but quits after 5 seconds and then I switch to the back tank. No problem with the back tank. But when I don't drive it till the next morning flipped the switch to the front and fires right up. I can get half way down the Rd before it cuts out. I was told that when the relay get warm it will shut the pump off. I don't get it Any ideas
@TheFSeries3 ай бұрын
Sounds like the front tanks’ pump is slowly going out So at that point, while cool it will drive a short distance, and as the pump warms up it just quits working until it cools Sorry for the luck bud! *I limped a truck home 50mi with that method, because I was a broke guy that couldnt afford 200+ dollars for a tow lol
@robertyeary55313 ай бұрын
Lucky I had extra gas in my back tank
@lupeesparza49573 ай бұрын
What are the oil filters for the 1992 Navistar 7.3 engine?
@lupeesparza49572 ай бұрын
X2
@Sarasdad913 ай бұрын
I got one and I love it. I use mine at 1/3 flame and was told it should get about 4 to 5 hours of burn time with a 1lb bottle.
@skyhunter19813 ай бұрын
Never hurts to add an extra ground .
@YHVHTeaches7773 ай бұрын
There wasn't an extra 7mm on the driver side right behind where the door opens? My f350 has one that's actually impossible to remove...and I don't know what to do
@zacharymullins78853 ай бұрын
For me your video showed the most important part, which attachment to use. Checked 4 different videos before finding yours. Appreciate you