Did you notice that the video goes blurry just when showing the solder (NOT) sticking??
@AayZeeHacks5 күн бұрын
Then how were you able to see it?
@abdbzou11 күн бұрын
الموسيقى مزعجة
@ComolesgustaChuparelpito21 күн бұрын
No muy fácil se ase eso dicen que con una cocina miny pero que produce el sonido yo intenté uno y no pude porque el sonido lo produce otra pieza mandándolo ala cocina pero como un multímetro que no tiene bip ba producir un bip nomas con una bocina no puede ser para que aga bip se ocupan dos piezas la bocina y otra pieza 🧩😂😢😅
@nana-bg4ci24 күн бұрын
mine didn't work:(
@poohkeytz1326 күн бұрын
Thats fake!!! Fake!!! Fake!!!
@AayZeeHacks26 күн бұрын
Only if it's not working for you
@mido.mido7729 күн бұрын
من فضلك كم مقدار الفيوز فى الافو ميتر دة
@AzamKhan-l2cАй бұрын
Try this trick but still not power on not charging... Maybe software dead... Any solution? Please....
@AayZeeHacksАй бұрын
It's probably an issue with the battery as it dies if not used or charged for a long time or even if gets overcharged. My suggestion would be to replace it with a new one. There won't be any issue with the software
@reddykavitha16172 ай бұрын
Hi my same model pho batty gone so where should I purchased again batry
@AayZeeHacks2 ай бұрын
Online from Amazon or any other store
@ColbyGidster2 ай бұрын
My watch stopped working after going low battery not charging or turning on again
@pandeyrahul9992 ай бұрын
Koi help nahi mila raha hai bit naya le lu lagta hai 😢😢😢
@AayZeeHacks2 ай бұрын
It will definitely work if you clean the bit thoroughly. There will be no point to repair it if you'll purchase a new bit anyway
@yuvrajyadav88912 ай бұрын
Thank you🎉🎉
@AayZeeHacks2 ай бұрын
You're welcome
@solderingsoldering3 ай бұрын
nice video boss
@ahmetaksoy20434 ай бұрын
Why you are using back ground music ,it is very disgusting
@AayZeeHacks4 ай бұрын
I can consider it in my future videos. Thanks for the feedback
@ytechbrotherGAMER4 ай бұрын
Hi sir please help me, its a caution battery and if there is little bit battery percentage in the battery then will it blast or not
@AayZeeHacks4 ай бұрын
Just peirce the first layer to make sure the air is released then it'll be safe
@Today_trend_official4 ай бұрын
This is so dangerous 😮
@AayZeeHacks4 ай бұрын
It's not if you do it carefully. Make sure to peirce the first layer only
@KAVISHALGAMER4 ай бұрын
Not work 😢 what i do pleas reply me
@AayZeeHacks4 ай бұрын
It may not work since the condition of the battery is not same for everyone. You might need to replace it
@AsheeshKumar-br5fl4 ай бұрын
Bai nahin ho rahi hai kya kre
@fault_youtube104 ай бұрын
😢😢
@buumbachaswala1424 ай бұрын
Now bro what causes this?
@AayZeeHacks4 ай бұрын
If your watch is not turned ON since a long time, the battery starts to drain on it's own and eventually dies.
@burstfireno16174 ай бұрын
didnt work for me. i used my screwmachine to rotate it on a sandpaper, i really sanded the surface througly but still not sticking
@AayZeeHacks4 ай бұрын
This is something that shouldn't not happen but even if this is the case I would advise you to apply some solder flux on it. Also make sure that the bit you're using is originally a solder bit and not any other metal rod.
@ShivamKumar-jt5bj4 ай бұрын
Nhi khul rha hai
@AayZeeHacks5 ай бұрын
Request access to the code, and it will be given to you shortly.
@SoyMrPaloma5 ай бұрын
No me funcionó 😢
@sirsyedhasan94105 ай бұрын
Keep it up beta ❤
@ravigaming50326 ай бұрын
Hii sir smart watch me charging ka pata tut gaya he me kya karu
@AayZeeHacks6 ай бұрын
Go to a repair shop for replacement
@peterwilson55286 ай бұрын
I can only hear that annoying music.
@joeery56996 ай бұрын
Wow,this actually works..i was able to make my solder tip heat up like 5x times faster by sanding my inner tips to make it thin
@alimohsinusmani6 ай бұрын
Useless video
@ChibiKeruchan6 ай бұрын
just buy a "Tip tinner" first clean your tip like how you did here in the video. then dip it to the Tip tinner. Always clean your tip using Steelwool and dip your the tip on the tip tinner before you store it so next time you use it the tip is not corroded.
@AayZeeHacks6 ай бұрын
I used to use the exact method as you said but in this video the tip is rusted. Therefore, I used sand paper first. Once it's cleaned we can do the same process as u said. Thanks for the advice 🙂
@Ghallu2806 ай бұрын
❤❤❤
@PEACE_EDITS7656 ай бұрын
Thanks bro it works
@devarapallikoteswarrao253 ай бұрын
really
@yudipunggol27116 ай бұрын
Hello, may I ask you a question? Whenever I transfer an audio on my dz09 it says "unsupported format" what should I do?
@HotDawg-rm3sm6 ай бұрын
I have the same problem😔
@AayZeeHacks6 ай бұрын
It's very simple first you need to take your memory card and save your audio in the MP3 format then try the process. I have made a video in which I showed how you can listen to audio in DZ09 check that out on my channel. Thanks
@HotDawg-rm3sm6 ай бұрын
@@AayZeeHacks Ok😊 ill check it out, thank you very much!
@HotDawg-rm3sm6 ай бұрын
@@AayZeeHacks hello again, sorry to bother you but it still doesn't work :< I followed exactly what you did but still did not work
@AayZeeHacks6 ай бұрын
I think there's an issue with the memory card because MP3 is the most common audio format. Here's what you can try. Connect your memory card with the computer then format it with either FAT32 or exFAT format try these two options and then save your mp3 audio and try to play, it should work. These two options depend on the compatibility of your memory card so u have to try both of the methods which works for u
@KRFFkartikGameing7 ай бұрын
Not working😢
@AayZeeHacks7 ай бұрын
It may not work for everyone
@AayZeeHacks8 ай бұрын
Hello, everyone I hope you all are fine. The reading on the serial monitor is not syncing with the video. [for example, when I bring my hand very close to the sensor the reading is still high or takes time to reduce]. This is due to an issue in editing the video else the project is working perfectly fine. I'm sorry for the inconvenience. Thanks :)
@rinkudash25759 ай бұрын
Thank you ❤️😍😍😍😍😍😍😍😍😍😍😍😍😍😍
@AayZeeHacks9 ай бұрын
You're welcome 🙂
@rajveerganerz9 ай бұрын
Bro charge karne se fatt nahi na jayga
@AayZeeHacks9 ай бұрын
No, it won't, just try to do it carefully and it'll work.
@sahilsingh119010 ай бұрын
Thanku❤
@VikashKumar-yt4hr10 ай бұрын
Thanks for sharing 🎉🎉
@TheFelix6311 ай бұрын
da menatte
@manujasathsarani797911 ай бұрын
Bro I couldn't connect to the charger my smart watch for 2 days now it's not charging what can I do . Please give me a solution 😢
@AayZeeHacks11 ай бұрын
There is the issue with the battery you have to replace it as you can see in my video that the battery starts to charge, although it was old, but the battery was functional. The possible reason is that your watch was off for a long time which caused the battery to die and therefore it's now useless. Once you use a new battery it will definitely work.🙂No worries
@sukritbaramansukritbaraman117610 ай бұрын
So i need to use new battery?
@AayZeeHacks10 ай бұрын
Yes
@intelin123 Жыл бұрын
Use brass sponge
@AayZeeHacks Жыл бұрын
Yeah that's also a good method to do so thanks
@antresia.9723 Жыл бұрын
I have a small screw driver and i broke the glass to take it out so am going to replace the tip, with the screwdriver i,ve a problem the tip is stuck and I can't get it to come out.
@AayZeeHacks Жыл бұрын
I understand, if you want to replace the solder bit with the screw driver bit. It might not work as it has a coating on it but you can still try it. If the old bit is stuck so it might be because of the rust or something. You can use rust removers like WD-40 to loosen the bit and try to take it out.
@antresia.9723 Жыл бұрын
@@AayZeeHacks ok. I,ll give it try
@alizoobear9687 Жыл бұрын
Thanks
@SandaruBrooo Жыл бұрын
Thanks
@armughal4817 Жыл бұрын
Please remove background music 😢
@AayZeeHacks Жыл бұрын
Thanks for your feedback. I can't change the music in this video, but I'll consider it for future content.
@mattzillarcworks64179 ай бұрын
Here's an idea.. add a mute button!!!! Love the music
@AayZeeHacks9 ай бұрын
Thanks for the idea I would definitely consider it as it will help other people as well :)
@Motivation-k9t Жыл бұрын
Bhai nahi ho rahi hae
@AayZeeHacks Жыл бұрын
It might not work for everyone. It not just depends on the process of repair but also upon the condition of your watch and for how long it's turned off. That matters too. I hope u understand
@sylvesterachilles2186 Жыл бұрын
Good idea bro
@Bike-Jo Жыл бұрын
I have the same motherboard But the experiment didn't work for me I used the clock bell Where can you get a bell like your That'
@AayZeeHacks Жыл бұрын
The thing I used is a buzzer/piezoelectric buzzer, it comes in various sizes and shapes and you can order it from any online store or either purchase it offline from an electronics market just showing my video so the shopkeeper can understand what you need.
@heloomeloo9233 Жыл бұрын
Bhai mene sab steps follow kiya par mera nhi hua😢😢😢
@spacepicture Жыл бұрын
Most manufacturers,say DO NOT USE SANDPAPER,TUT TUT TUT
@AayZeeHacks Жыл бұрын
If the bit that u are using is rusted only then use sandpaper else don't use it