Hi there I don't want to sound daft but would this be a similar process for the face-lift insignia? Many thanks on the video it was very helpful to watch

Useful video, thanks. I can't see my fuel filter. It's a 2015 2l diesel. Do I need to remove a cover to find it? Thanks 👍

Did you remove the undertray?

Cheers mate

This guys funny😂 Oy ya bastard dropped the filter in the oil bucket 😂😂😂

Great video, just a little confused, you state the torque setting for the sump drain plug is 25 nm. but the HAYNES Insignia manual states 14nm.

hi. does this apply to 1.8 sri insignia aswell?

Not really showing how to get the old pipe out and new pipe in.

I know this is old and maybe you'll not see this but, do you really need to bleed the brakes, can you not just leave the pipe on and wind the piston back in? I know it'll be harder but I'm doing this on my own, I've done the front but not the back before

Great video; would you consider putting ceramic grease on the slide bolts?

Hi please can you tell me why my insignia 2011 always loses the oil cap, I always tighten it but it always comes loose and enough oil is escaping from there. Secondly, under the cabinet driver's side. After switching the engine off, there's this sound like long bip sound that slowly goes off. The last. In the air system or hydraulic system, there's also sound like gas out of a cow. But only sometimes not always. I want to be sure of what it's going on before I will go to mechanic. Sometimes it can be something that doesn't need a repair hope. Thanks

Hi, I just came across this video and noticed you haven't used a computer to put handbrake into service mode. Isn't it necessary. Only asking because iv been told thats the process and i need mine doing

Great Video 👍

Top video doing sons insignia this morning rear springs disc and pads and abs sensor,,,videos helped alot clrar and easy sprsk

Thank you posting!!! Gonna try this today

L

Thanks for the vid - do you think both rear coil springs should always be replaced at the same time or it is fine to just do one?

Thank you for taking the time to make and share this very helpful video.

Nice and easy. Mk 7 RWD engine model is tight in LHS corner and requires air pipe and air sensor removal.

Check oil capacity, expected 7 L to drop not 9L. Sump sizes vary!!! My van 2.4 diesel 2011 ( ex minibus ) RWD. I needed a strap for plastic housing removal. Socket just slipped !😮

Finally an actual in-depth video for an Impreza dash, big cheers for that mate

I’ve just started working on cars again after a 25 year Hiatus! My confidence is growing and your video has given me the additional confidence I need to continue to do it myself! I was going to use ramps and never thought about just jacking one side! How did you deal with the engine undertray?Thanks and great video btw!

Did you need a longer glow plug with the sensor on top? Thks. Great video. Ty

Another good tip is to take the sump off and wash it in a parts washer, thats what my tutor in college done when he seviced his own cars.

Nice one. I'd been meaning to do basic servicing on my own cars for years and it took covid to finally push me to do it. Saved hundreds since doing a full service, drop links, arb bushes and discs+pads. If your car is fairly modern and nothing is badly rusted it really is easy to do routine servicing and even some suspension work with a basic toolkit. Even for my city car the main dealer wants >£200 for just a oil+filter change! Costs me £35 and takes half hour.. FYI: The service fill for the 1.6TDi IIRC is 4.3 litres.

Great vid mate, when bleeding the brakes do you have to repeat the same process on the other side of car or is it sorted once you’ve bled one side? Cheers

Had the same problem on my Astra vxr , remove radio and disconnect it , also disconnect battery … leave for 30 min reconnect everything and it came back .

Does anyone who’s done this know if it’s meant to be a very hard struggle to get the 2 pipes to get into the holes where the 10m goes, I get it’s high pressure pipes and not much movement but I was ready to lose my head

Felicitări. 🤝🤝

I just did the full service but I forgot to lubricate the rubber sealings on the oil filter, will that be a problem? The oil filter was also quite hard to attach since it didnt stick to the housing, but i eventually managed and it did screw back on nicely. What do you think will i have problems? i did use the same filter as you, also been driving the car for 3 days no problems

Excellent video!!!

Hi mate, great video! Going to attempt this on my insignia. Quick question, how do i know ive tightened them to 25nm? Or is that the tool fitment id use? Sorry if daft question

I changed the heater core in the car, and now my ac wont throw cold air. Do you know what wires that I needed to clip on for those?

Yeah exactly what I came for nevermind any of the disassembly that's not the least bit important

What’s the Protector called?

Too complicated with all these pipes. Need another approach

Top job explained 👍

2015 vx line sri 2l diesel filter housing is shocking, the filter wouldn't budge and has resulted in a snapped fuel line as it spun off its bracket, just a heads up for others doing this model, ive a head ache from diesel fumes and now a head ache of sourcing the housing to go with it 😂 decent video mate all else was a breeze, thank you.

Great help, thank you.

Sound mate good video got mine to do Friday inner tie bars track rod ends and bottom ball joints boths sides gonna use my windy chisel to remove the old ball joints lol cheers bud mines rwd so shouldn't be to bad

Hey bro, you still using this exhaust config? Not too loud on highways? Drone? I have Martelius with stock cat but thinking about to put in a decat downpipe, maybe with an extra silencer from Martelius. Thank you!

Hey! What instruments do you use?

Where about is the fuel filter? Location wise?

Id know that voice anywhere, nice job Dave. Ive been buying Transit Custom and have been looking up jobs like this one. You made it look easy mind.😊

Superb vid helped me loads ive just replaced mine and all the tips came in handy thank you and yes it is a nightmare but took 1 hr and half start to finish

Thanks for the video, it looks really straightforward, and so informative. My question is, how would you know if they are glow plugs with or without sensors? There's a bit of a price difference so I am hoping my 2015 model needs ones without sensors. Thanks!

Thank you

Service

Did you manage to sort the ESP, ABS and brake pad lights? Mine are on and no codes coming up and it’s doing my head in. Cheers

Great vid.... gave me info I needed. Had to shout " you lucky b@stid!" when your bottom part of ball joint spun tho... Mine is seized so bad.... more heat + brute force and ignorance lol..