9 ай бұрын
10 ай бұрын
11 ай бұрын
Жыл бұрын
Жыл бұрын
2 жыл бұрын
2 жыл бұрын
Пікірлер
@stevebergman1573 Күн бұрын
Those are installed per Decktite protocol
@Hankcrank-tf9yo 2 күн бұрын
Why are there 2 stink pipes 1 ft apart ? They should have been combined by the pumber.
@robynmacneil3554 3 күн бұрын
This video was great! So many wishy washy videos that say alot yet say nothing lol! Thank you for being clear and showing the details. You're a great teacher. I got my answers and I'm heading back up! Thank you!!!
@Framer_Mike 9 күн бұрын
You should have been standing on the roof the whole time. teach them properly, Major!
@dannybarnhill3052 14 күн бұрын
What stops the water coming in at the rib? Yea caulk! Why even put a pipe flashing on? Silly. Water gets in the overlap and will feed under the flashing, only caulk stops it.
@dylanmisquez2961 15 күн бұрын
😂😂 I was about to say if your pipe is center of rib you can mark and cut/bend your diamond first and then mark your z bar glad I watched to the end lol
@araninarossini 23 күн бұрын
How do I make sure my roofer does the flashing and water barrier properly on my skylights?
@danielbays5308 23 күн бұрын
It seems to me thinking ahead and proper lay is the best way to go.. nice work anyway.
@emerican0311 23 күн бұрын
I can really tell you know what you’re doing! Big rain and wind storm up here in Maine right now..was watching a show with my girl and heard a dripping behind me..sure enough..leak coming from the chimney near the ceiling. I went up into the attic and can see where it’s leaking and I assume it has to do with what you replaced here. I took a lot of notes from your video and will be fixing the leak! Thanks for taking the time to explain everything.
@Mark-gr3ii 24 күн бұрын
Great video, this man does some pretty work and obviously knows what he is doing. If it is feasible Consider the location of the vent pipes to determine where you install the first panel, and this problem can easily be avoided. Be sure to add 1/8 or 1/4 inch for each panel to adjust for the inevitable gain during installation. For new construction, have the plumbers move the pipe so it comes up through the center of the panel.
@597158madroofer 26 күн бұрын
your not building a swiss watch ... it's a roof ,,
@sweetlou6539 26 күн бұрын
We go right to the deck for the 1st layer..interesting install. I don't hate ❤
@DutchStar 26 күн бұрын
Watched a guy tape thin cardboard to his tongs. No tool marks on the crimp.
@saudielarcos6033 28 күн бұрын
Do it on an actual roof!
@dickslocum Ай бұрын
so one inch spacing for wind abatement on the top piece but only a few screws at the intermediate connection of the under z parts. How does that work for Florida Wind mitigation inspections. I need to do four of them on my roof from 2002 to meet the new upgraded fla standards.
@mrtahoe Ай бұрын
2:39 haha just do it correctly and like I said ain’t got no time for all that 😂
@mrtahoe Ай бұрын
Ain’t got time for all that. This should have already been done.
@curtrodgers5395 Ай бұрын
This has to be the most stupid install i have ever seen the boot's are made to seal over the ridge of the metal roof, they just need to be installed correctly.
@darrellk8517 Ай бұрын
Thanks for the information... Too bad you are not in the South Dallas area... I have two pipes that have the boots up over the seams. Now I know what should be done once I find a repetable roofer in the Waxahachie Texas area.. Again thanks. And thanks to the other comments that show the success of them mirroring your instructions.
@scottsowder Ай бұрын
quality work
@biggreenavocado Ай бұрын
I did not expect it to pan to American /Australian Thor😂😂
@13clymeda Ай бұрын
Awesome demonstration. I had a hard time finding a video or tutorial on trim work like this on a seamless metal roof.
@paulcaruana4090 2 ай бұрын
Love watching guys put it on wrong in all these videos. It must wrap onto fascia. Imagine a gutter on fascia that freezes. Where is the water behind the ice going to travel???? Right up under the drip into the BARE wood and leak. It instructs you in the directions on the package. 4" minimum ONTO fascia. Then install drip. Feel free to put a strip on top of dripedge sealing everything
@phildenyse1254 2 ай бұрын
This is an awesome presentation and a true professional. Wonderful video. Much respect and thanks for showing how it is done right.
@paulbraam332 2 ай бұрын
The ice and water debate over under or both is just as bad as putting a roll of toilet paper on the toilet paper dispenser over or under
@rusty-y8r 2 ай бұрын
forward pressure cut the shingle near the nail.
@richardmckrell4899 2 ай бұрын
His first layer of ice and water is unnecessary. Ice and water is only needed overlapping the boot flange above. The big mistake he's making is not adhering the ice and water to the sheathing and then installing the underlayment over the ice and water. He doesn't understand basic roofing concepts.
@Camilo-q1d 2 ай бұрын
Thank you so much for this video. I have a mountain cabin and the gaskets got torn to shreds by 3-5' of snow for the last 3 winters and bent the ABS vent pipes. It took me all day to replace the vent pipes and gaskets, and the one on the rib I used this exact same technique and it worked perfectly. Such clear instruction I really appreciate it, probably saved me >$1000.
@Spring_27_84 2 ай бұрын
Video cut at the most important info lol
@MaxBoom-n3r 2 ай бұрын
Why isn’t your ice and water on top of the drip edge?
@j.kelley1685 Ай бұрын
Ice and water shield has to be adhered to the wood. You can add extra ice and water over the drip edge bonding it to the first layer if you like. I don't understand why people only adhere it over the drip edge that makes no sense. The ice and water shield needs to be on the wood because of its adhesive membrane and the nails that go through the drip edge need to go through that adhesive med brain into the wood so that the membrane forms around the nail sealing it in. If you only put it on the drip edge then all of your nailing that goes through the drip edge is puncturing your roof sheathing and doing absolutely nothing. Always remember that ice and water shield needs to have contact with all of the wood first. Then you can cut strips after your drip edges installed over the ice and water to put another seal.
@MaxBoom-n3r Ай бұрын
@ I greatly appreciate the feedback! Thank you! I have 6 townhouses that got hail damage and now have a new roof. I’ve installed shingles before as a summer job in college. Learned a lot and was able to identify some major issues with the way the contractors installed the new roof. Things like putting nails through the face of the drip edge, spray painting the old galv vents instead of installing the new black ones that were included in the insurance claim, finding major shingle damage to the new roof as it was installed, incorrect installation of parts of the roof cap, and incorrect starter shingle installation just to name a few. This contractor insisted they were GAF certified and legal, but when they showed up with no safety equipment, and couldn’t speak English, I started to get seriously suspicious.
@victorsanchez8294 2 ай бұрын
Take time but saving $$ a lot problems👍
@wambo6528 2 ай бұрын
You left the nail exposed on the center of the pipe boot flashing. LEAK - I am a commercial roof consultant in Florida, RRC, RRO, so ya, I kinda know this.,
@benzoamg01 3 ай бұрын
Rookie
@benzoamg01 3 ай бұрын
Show it on an actual roof
@josh2711 3 ай бұрын
Why not do ice and water on bottom and have the synthetic paper run over the drip edge. Seems like the cheapest way to get the over and under.
@erwinbenally8027 3 ай бұрын
Good job. You do good work. Thanks for sharing
@vince6829 3 ай бұрын
Nice job. Thanks for sharing your knowledge.
@davidparker9676 3 ай бұрын
Do you stagger the paper seams on low pitched roof when you say to use 2 layers of paper?
@armandoyourpersonaljeweler7558 3 ай бұрын
Thanks for the informative video. Is this needed for a low rib metal roof instead of standing seam?
@avionicgoddess 3 ай бұрын
Would it be feasible to generally follow this method with a metal roof?
@stevensolnitzky4049 3 ай бұрын
One of the best productions. Good camera showing close details, good explanation and speaks very well without stumbling. Good sound quality. Joy to watch. So many just don't get how bad their production is.....thank you . Shout out to Velux. Also not a sponsor, but it seems like they supply great product and support.
@ralph95 3 ай бұрын
Are they leaking?
@ninjaturtles9093 4 ай бұрын
I thought you weren’t supposed to do the sides of roof if was pitched ?
@shawnmendrek3544 4 ай бұрын
I am rusty ty.
@heyyo6122 4 ай бұрын
so after the ice shield you start the under layment at the top ?? or does it matter ? I thought it starts from bottom up like the shingles
@CenvarRoofingandSolar 4 ай бұрын
For this model, it would seem that the under layment starts at the top, but you're correct. It starts from the bottom up. If we had a larger model we'd be adding another layer on top of that and then another on top of that.
@sh1ngledaddii85 4 ай бұрын
You explain about seam nails then proceed to do it 😂
@brucewalter3326 4 ай бұрын
How can I get this guy to come replace my skylight?
@CenvarRoofingandSolar 4 ай бұрын
Live in Virginia? Any chance you want to pay for travel, room and board? 🤣
@MrRerod 4 ай бұрын
First time installer.. So why do I see some guys peel off half the backing as they unroll the Ice and Water? Thanks
@jeffreybates5327 4 ай бұрын
How much do people usually charge to change these out?
@CenvarRoofingandSolar 4 ай бұрын
If we had to take all considerations out... we'd say around $1,200 per. Pricing factors to consider would be pitch, how many stories up is the roof.. etc.
@garysgarage.2841 5 ай бұрын
I have 30yo Anderson power operated skylights that don't leak that I know but don't operate properly. Is updating them expensive labor wise?