Bro….. there’s a tool for this. It’s called a “crank puller”
@mikepoint471714 күн бұрын
Nice work , I used a tie rod / ball joint remover . Cheers 🇨🇦
@user-fb5lo6tx4t27 күн бұрын
You need a crank puller it cost like 13 dollars
@tpokob.d.h79928 күн бұрын
Ça a marcher pour moi Merci beaucoup 😊 ❤
@ricotheartАй бұрын
Thank you so much
@vin17flores72Ай бұрын
Is it a self extracting crank arm?
@vin17flores72Ай бұрын
You need to remove the tip of the crank remover tool and try again. You have obviously tried removing the crank arm without removing the tip which is obviously by the marks on the internal thread of the arm has just pressed them off
@ivanhyuga124Ай бұрын
Godbless tutorials like these
@cecilecorpuz5735Ай бұрын
A CYCLUS crank arm repair kit would fix this with no problems at all.
@Hollywoodhops12 ай бұрын
This will damage/bend aluminum of crankarm.
@bartekrokicki27312 ай бұрын
Thank you so much! When all the hope was lost... Boom and it's off!
@univerzum98302 ай бұрын
Thank you very much bro! You are the best in the world!!! ❤❤❤Very helpful video!!!
@Iamnatewayne2 ай бұрын
A pulley puller could help in this situation as well.
@hithereyou99912 ай бұрын
Your crank arm is still attached, sir.
@user-sp3og9qs9s3 ай бұрын
You should use a 8mm or 10mm socket insted of the allen key. And then use a 3 jaw puller.
@00019g3 ай бұрын
How do I get a lock nut off that is rusted onto the frame
@ediszuga-ic8wc3 ай бұрын
I broke my wrench😂
@kylejacktucker5 ай бұрын
My centre bolt is rounded and my puller roumded the exterior so idk what to do
@mrreemann37395 ай бұрын
What? You didn't show shit!
@mo3skii6 ай бұрын
Thank you so MUCH. That worked 💪 🎉😅
@mattlee58327 ай бұрын
Saviour!!
@simonjandrell58977 ай бұрын
yep I got two dodgy garbage bikes and both cranks are seized tight.. great 😂
@fareedmumin7 ай бұрын
freakin awesome bro thanks. this is what youtube shorts are for
@user-qs8og7uk9g9 ай бұрын
This is what you need to get to get to your goddamn point
@luigiprovencher88889 ай бұрын
Now how do you fix the threads of the crank arm so that you don't have to throw it away? I'm going to try doing thing with a ratchet extension and a rubber mallet.
@kowakowalenka61929 ай бұрын
Thanks 🎉 bike fiked
@keannejoshpanaguiton51749 ай бұрын
Thank you bro it work❤
@huddledmarmot10 ай бұрын
The head on the crank puller you used is too large, you can see where it was driving into the edges of the square hole in the crank. You need a square taper crank puller, or the park tool with a smaller drive disc.
@roberteltze485010 ай бұрын
I hate those old square bottom brackets. I had so many problems with crank arms coming loose. Good thing we're two generations past those and the current generation has been around about 20 years. Good riddance to bad design.
@imred.n10 ай бұрын
very effective🔥🔥👏👏👏
@Mattlawton-ft6ew11 ай бұрын
A long bolt will also do it 👍
@nigelsmith494811 ай бұрын
Thanks, worked a charm
@listomachine6198 Жыл бұрын
Perfect sir! Thank you
@EK-ej3ll Жыл бұрын
Better than what I would’ve done which is cut into the arm and try to split it with a hammer and chisel.
@Bobby_Uterus Жыл бұрын
Imagine just being able to smack that crank arm off with a rubber mallet. Stuffing that Allen key in the end of the threaded area of that spindle is going to mess the threads up even more. Take it to a shop if you don’t know what you are doing. It’s clear you were not using the crank puller correctly by the marks you left. You shouldn’t recommend people be doing stuff like this. It’s bad advise even if you were able to get the am off.
@armycavin Жыл бұрын
Amazing. Furst thought was holy hell it actually worked. Will use this in the future for sure
@IMikePlays Жыл бұрын
If it doesn't budge, HAMMER TIME!
@nezzey Жыл бұрын
ONLY THING THAT WORKED OUT OF THOUSANDS OF TUTORIALS AND THE OUMERS CRANK PULLER RETURNING THE TRASH AND THANKING YOU!😊
@BusterTheNPC Жыл бұрын
how do I fix my mountain bike crank arm, it detached from my bike
@c0mbozz353 Жыл бұрын
I didn’t have anywhere to rest the hex tench so I put it in my bench vice and it worked. I didn’t think it would work but it did so thanks
@sethreign8103 Жыл бұрын
Good lesson for idiots trying to damage their bikes 🤦♂️
@miocarrido1686 Жыл бұрын
Yow bro your a life saver thank you
@acuriouseye Жыл бұрын
I used an angle grinder, taking care not to grind too much of the spline. I cut straight across, and diagonally up from under the arm, around the 3 accessible sides. Your way sounds easier for those who can prop their hex wrench.
@tomcrossan7996 Жыл бұрын
Saved me from a trip to the bike shop that would probably cost 40€. Thanks man 👍
@kianmoane6320 Жыл бұрын
I did it with some wd40 too lubricate it then wiggle it back and forth and it's should come of