Clear tape in the magic marker will allow you to make gasket sizes

And for those that want to make their mini bike gas line last longer than using this aquarium style type tubing go to your local tractor supply center and ask for rubber fuel line tubing for riding lawnmowers

That thing that he is calling an ignition is not an ignition. It’s just a magneto.

I just caught this video on my feed. Not sure why I’m surprised at the professional keyboard Porter’s poking fun, to no avail. I enjoy your enthusiasm and appreciate you trying to help others gain performance. Many of these techniques are what we use in the chainsaw racing world👍🏻

Not sure if you reply to comments still but is it just motor oil u put in the clutch

Hey the real reason why that you want to have your fuel inlet rough your intake Port is because it comes all the way in real smooth so it can roll faster but when it gets right down to the nitty gritty before it enters the carburetor we want it to be cross hatched or rough surface because it splits the fuel up from liquid to vapor and viper ignites better it makes a bigger explosion with less fire so that is the real reason why that you want to cross hatch or have it your fuel intake really rough just right before it hits the carburetor no where before that though because it does run faster when it's smooth but it's liquid we want it to transfer to vapor before it hits the carburetor so it when it's injected then it will therefore be ignited a lot better

Actually that part of the crank case that you mentioned fuel goes through is actually a crank case pressure point feeding pulse of air from the crank case over there by the base gasket, it directs those air pulses towards the metering diaphragm for the carb to pump fuel from the tank that sits below therefore no gravity. Only used for a below level tank that needs assistance to pump upward

7:56

Volume's a little low :/

8 years holy, you're ahead of your time!

There called vice grips

You helped me so much man thank you !

There were a few good tips and a few bad tips in that video, but at the end of the day its just a tiny 2 stroke Chinese motor so there is not much u can do to the motor to get it to go harder. Changing to hotter or colder plugs can help and jetting the carb & adding a better filter is about all you can do to the engine to make a noticeable difference, but heaps of power can be gained by changing the exhaust expansion chamber tuned lengths of pipe (which are the pipes before & after the widest part of the exhaust system.)

Two thumbs up ! I just came across your stuff and got a lot of usefull info Thankyou! I'm now subscribed. I have a scooter with the same 49cc engine is there anyway you can tell me what kind it is and where to go for parts on line I want to order a knew top end . Thanks

Shaving metal from the crank can put the crank out of balance

Great video i have a ram with 5.7 HEMI with full custom exhaust system i extended the Y pipe merge to the back near to rear tires i have noticed huge gain especially a low rpm part throttle

So closer merge point for higher rpm’s and further merge point for lower rpm’s?

I would like to add to your brilliant video is polish the crank so it travels through the oil and no drag

I have the same engine what carb are you using instead of the stock one?

Is that stock

Hi what color name is that?

What kind exhaust is it bro?

sounds almost exactly like my car haha, setup lookin nice too

Just fyi pushing the bulb does not put gas in the engine.

Does scavenging occur outside of the manifold ? Or should I say past the catalytic converter ???

Aye man I have the same car can you please tell me the name of the exhaust and what else’s have you do to make it sound like that

Everyone is now dumber after watching this.

Sounds very good man !!

Can barely hear you

I have same car sounds 🔥🔥🔥🔥

Race cam..lol

It’s allmost like a science. If you don’t have gas to go it will turn off

And to present tonight's major showcase its Andriy.......

"Other thing you can do is......get one of these....." 🤣🤣 I love this guy

I thank You for the info !

Is this patched?

Poor guy tried so hard to sound like he knows what hes talking about. Go home

Where can buy it parts

Did you ever change the sprocket size?

Man this is the best exhaust setup for 330ci by far. I appreciate your dedication and hard work that went to this car as a whole. I own one as well but man, you are giving me some mad ideas. Those BBS's are killer btw

I'm trying to figure out how to make a big bore kit for it and take it up to 47mm or more have you seen anything on that

I’m probably gonna accidentally kill myself with this information

Dude. Your info is great, but your audio sucks

What's your wheels set up? Looks amazing!!

Sounds clean What muffler are you running?

polishing the piston ring will cause excessive cylinder leakage......probably want to avoid that

How big is the exhaust pipe

What diameter size your piston

0:01 step 1 to make pocketbike faster: put the engine in

What alloys are they , thanks.