This new formula didn't do squat for me unless Meguiar's Hybrid Ceramic Wax had already been applied. Maybe this stuff acts as a booster for existing protection?

Can 3-D bug remover be used on the front of radiator, as I cannot access the radiator from behind. Thanks for your great video.

This product is very similar to other “one step” polishes where the cut is determined by the pad rather than the polish. You could finish up with their red “jewel” pad which claims very high gloss when finished

How do you buy these wholesale online?

It looks like you know what your doing! I admire your work! But please use Nitrile gloves! Even Ivan says these coatings are extremely dangerous for your internal organs! Please refer to Diy detail and please listen to Ivan himself. Or just ask?

What a great video ! I am super old so yes I have been using this and MANY other newer products for decades. I was around back in the days of those commercials and the consumer reports on how good it was. It’s a solid product, should be called the twice a year polish. You do your vehicle 2 times a year your ride will look good for 200,000 miles living outside. I speak from experience, on a few vehicles.

Lmao the intro is hilarious. Wooops. 😂 glass cleaner 😂

Even the chemists at Griots are confused by this test. No way they would expect speed shine to outlast 3 in 1. 🤣

the reason that it is more expensive on Amazon is because people buy it up ( like Mr. Pink ) from Wal-Mart and resell it . Two of my 3 local Wally Worlds had to put a two per customer buying limit on them because 1 individual was buying most of the stock in 1 sweep every time they restocked . He'd get all of the suds.lab , CGs, and Adam's products and sell them on his Amazon and ebay sites at a significant mark-up . The other Wal-Mart was like " hey we are selling the crap out of it , let it go " .

Excellent video! I just have to ask why do you wash bottom up? I was always taught to wash top down… does it make a difference? Or are the products you use just that good? Not trying at all to disrespect in any way, just a genuine question on your method.

I have used the product. It works. Your test hood is up in that vertical position. Nothing is going to bead up in that position. Gravity is forcing the water off. Use your test hood horizontally to be fair.

What was that noise lol it sounded like you were sucking air through a mask or something

Dittos on 3D Products

This thing is really bad. That plastic bit that connected the rod broke for me and you have buy the entire thing all over again. Shitty German engineering again

I use Adapt and also DIY WL. The winner is... DIY Waterless. On the paint they both perform about the same. Both smell great but the grape juice smell of DIY is unique. The difference make is the glass. Adapt leaves a smear when applied to glass. I use the DIY WL to remove the smears on the glass and it cleans to a sparkle. I would think that it is putting a cleaner coat then on paint as well. Stuff rocks and is a great drying aid as well. Lastly, DIY Mist is too expensive, use DIY WL instead.

I finally got around to using ADS Tire cleaner. After two rounds of a fan favorite, I sprayed ADS and I got immediate browning. Their Tire+ Conditioner quality leaves a nice finish.

I prefer glossy/shiny. Really makes the wheels pop.

Good job. I believe adding All Clean, Iron Remover, and PSD Towel to the process, may have revealed more favorable results. Iron contamination has little to do with the water supply and mostly with the brakes. Not just yours, bet everyone around you when driving! Also, Kia engines are more prone to burning oil, which can accumulate residue on the back of the vehicle. Which is why the back 1/3 of the vehicle had more sheeting. All Clean would have been more effective at removing that "oil" film.

Great video of a torcher test. The elements of nature are the best test ! 😉

Si02 Pro is my absolute favourite. No smearing, fast and easy. Better than every other I have tried, and I have tried a lot. Great value too. Vonixx is kicking some ass of the big brands.

This is not supposed to be a foundation sealant it only use to maintain the existing coating only. Also the product does makes the panel sheet the water at a much quicker rate so idk what you expect lol

Amazing video man! Thank you so much for your time and effort! I have used nufinish original for years and its always been amazing. After his I might be looking at their ceramic or graphene , but i do like the slickness when i touch the side of my car.

If im doing a full decon on a coating, I'll hit it with an alkaline wash like Carpro Lift or NV Snow+ via foam cannon, let dwell, rinse thoroughly, then follow with an acidic wash such as Carpro Descale also via foam cannon again letting it dwell then thorough rinse. After this I'll either bucket wash with either one of these products depending whether im going after road grime or water spots. But you can also do one after the other. You could then if needed, use a dedicated waterspot remover and iron remover to spray on and spread with a soft towel then rinse. If I'm not seeing much improvement in water behaviour then I'd be thinking about reapplying another coating.

Nn serve poca durata batteria 😢😢

Shoot, I feel the tape has a hand in this.. not in regard to hydrophobics, but how the water falls from above. The tap creates a lip, and it obscures what maybe can be seen if it wasn’t there..

Hows the diy 5 year coating holding up on your other car?

Why dont you get a Bluetooth mic?

Looks like for the price and single layer, cquartz 3.0 has been the standout

Which wipe on clear coat did you use?

It was repelling your money from your wallet

Great job bro. As I work through my pads and need replacements I’m only going to be getting their system. So simple and effective

It is Lake Country’s pad wash. Good stuff. We run it in our pad washers & do laundry with it if we run out of Rags to Riches

The stacks are really doing well. Im curious if 2 layers of the same would be similar? We need a time macheen to put some hydrolite on there. Im sure yvan knows a guy

Sorry but is this really how coatings look after just 5 months?

Thanks for the continued update.

Perhaps if you wash with the 2 part wash first then the second product 2nd you will get similar results.

Has anyone used this for headlights?

I have used this multiple times. It actually cuts better than you would expect. Wash, pull in garage, clay, Detox, first coat Friday night, second coat Saturday night, better butter wax Sunday night. 🛡️✨😎

Can you apply Adams Advance Graphene over a wax based ceramic?

With diy wool pad you get a haze but the yellow an red one you won't have to try them out I just got the diy rotary today

In terms of water repellancy, this is actually decently disappointing

DIY details coatings seem to clog super easy and are much higher maintenance. 8 year coating...bunch of bs..will last not even half of that.

Thanks for the tests. You just saved me $15 from Walmart. I cannot believe how bad this product is vs the old version. Subbed.

I just bought it 😢 should I return it?

I drive the same distance and park indoors at night and outdoor all day in the hot sun. I know everyone wants the new small boutique brands but my Gtechniq CSL+ exo v5 still beading like day 1 over a year later. I haven't even had to decon of any sort, outside of 2 alkaline pre washes. Usually just ph neutral soaps or rinseless.

From the testing I've seen on KZbin, ceramic-coatings offer zero UV protection

Hey Martin. I’ve been using Koch chemie pol star and recently purchased sintra pro to try. I’ve had good luck with pol star but there are times I wished it was a little stronger.

Bruh them ciggy butts in the driveway 👀

It's because WSR is hydrophobic. 8year ceramic coating almost died afer 1year- lol :D

I think 8 years is a BS claim. I think they over promise and under deliver like so many other ceramic companies.