That took a bit but it’s a honda so it starts right up! My honda prelude has a idle fluctuate when it idles for ahout 3 minutes in cold weather, since I believe the coolant system needs to be bleeded
@seantheenthusiast8 күн бұрын
Yeah, for whatever reason, the starter on the seventh gen accords draw so much amperage, and they're so sluggish to start the engine. It's almost like starting a subaru. My old civic started much faster than this, but i'm not concerned, really. Possibly, by the end of next year, I might trade this in for an Acura.
@EvanNyameyeTachie-Menson9 күн бұрын
Sweet sweet Melody ☺️
@tonyf.lawrence9116 күн бұрын
Does this Furnace have a filter that has to be replaced within it? I’m having an issue where it’s not reaching the set temperature I set it to. I had a technician come out and he replaced my pressure switch. That seemed to work for a few hours but now it’s not reaching the set temperature. Are you able to provide me with any advice?
@seantheenthusiast16 күн бұрын
Yes. A dirty filter can definitely cause a problem where it's not being able to keep up as it's tripping a high limit safety inside the unit.
@seantheenthusiast16 күн бұрын
Either the filter is located near the furnace. Or it's located in a return somewhere. If dirty, replace it or wash it if you have a washiable style.
@tonyf.lawrence9116 күн бұрын
was yours located in the attic? The filters I been changing has been for the return inlets which I have in the ceiling upstairs and another downstairs in the living room? If there is one in the attic where would it be. My furnace is horizontal.
@seantheenthusiast16 күн бұрын
Mine is in the basement. horizontal units are the same way, They're just sideways. Most horizontals in attics have filters on the right side of the unit. Some of them are located on the left, and there's a little door on it.
@tonyf.lawrence9116 күн бұрын
Thank you. I’ll check that out because from my initial look I did not see an access door.
@itsbeatzz929 күн бұрын
You probably know me but I got the same blower too and did a muffler upgrade I took off a few parts inside of the muffler and it’s louder and has a little more boost
@seantheenthusiast29 күн бұрын
Nice! Yeah I do remember you by the way
@itsbeatzz928 күн бұрын
Want my number
@seantheenthusiast28 күн бұрын
Sure
@kevinjohnson3964Ай бұрын
Oh your into weather radios to
@seantheenthusiastАй бұрын
Yessir
@jeffwebb5072Ай бұрын
This was ridiculous to watch, no explanations and going to damn fast. Stupid "how to" video.
@seantheenthusiastАй бұрын
This blower is still going strong as of November 2024. In the summer of 2021, the original carburetor went bad and was replaced with a new oem carburetor. That same year, the fuel lines and grommet were changed as well. This summer, the spark plug was changed, the carburetor gasket was replaced, and the carburetor was readjusted. In early November, I cleaned the muffler, spark arrestor screen, and exhaust port. That goes to show you how long these old japanese blowers will last as long as you take care of them. They're are like Hondas! Sure, this blower may not have as much power as the newer models Echo sells today, but it can still get the job done. Quick tip: When replacing your spark plug, make sure you get the oem plug because I once ran a Chinese aftermarket plug in mine, and the blower had starting issues and flooded itself frequently, and putting the original spark plug back in it fixed the problem. When I bought my SRM 230 used, it had an aftermarket plug on it, so i changed it out, and it runs even better! So always get a real oem spark plug and not a clone!
@seantheenthusiastАй бұрын
This blower is still going strong as of November 2024. In the summer of 2021, the original carburetor went bad and was replaced with a new oem carburetor. That same year, the fuel lines and grommet were changed as well. This summer, the spark plug was changed, the carburetor gasket was replaced, and the carburetor was readjusted. In early November, I cleaned the muffler, spark arrestor screen, and exhaust port. That goes to show you how long these old japanese blowers will last as long as you take care of them. They're are like Hondas! Sure, this blower may not have as much power as the newer models Echo sells today, but it can still get the job done. Quick tip: When replacing your spark plug, make sure you get the oem plug because I once ran a Chinese aftermarket plug in mine, and the blower had starting issues and flooded itself frequently, and putting the original spark plug back in it fixed the problem. When I bought my SRM 230 used, it had an aftermarket plug on it, so i changed it out, and it runs even better! So always get a real oem spark plug and not a clone!
@gabrielzahn1316Ай бұрын
What shifter is it?
@seantheenthusiastАй бұрын
TH8A by Thrustmaster
@StuffStudierАй бұрын
I can really hear the AC in that clip!
@seantheenthusiastАй бұрын
Yup that was the idea!
@StuffStudier2 ай бұрын
That draft enducer motor is definitely noisy! Those flames are very nice and blue! Great startup
@seantheenthusiast2 ай бұрын
It's not as noisy in person though. In comparison last year it was worse, So the fix has helped a little. Now because of the new thermostat changes It's less likely to run during the daytime So in this video I intentionally made it run By turning up the thermostat to 72. Now that's fine because Running it for an extended period of time Will show me that I can trust it and I won't be wrenching on it in the middle of winter when heats actually needed.
@seantheenthusiast2 ай бұрын
This thing really stank when I first ran it. The funny thing is that we're now back to using air conditioning again.
@StuffStudier2 ай бұрын
@@seantheenthusiast I’m using my ac right now but that’s because my brother decided to turn the heat to 75 and claimed he only did to 72! (Only my bedroom AC) But it ran like a 25 minute cycle to go from 70-75. My furnace didn’t have a stinky smell it just had a slight dusty smell but not burning or anything. Most likely just some dust in the air return vents and needing a new filter for the season
@StuffStudier2 ай бұрын
@@seantheenthusiast The cameras always either don’t pick it up or do too much. My thermostat jumps a degree when it’s finished hit that’s fine because it gets a break in between cycles. My house isn’t very insulated so it drops a bit faster than other houses
@StuffStudier2 ай бұрын
@@seantheenthusiastAlso I didn’t see one speck of an orange flash. Your heat exchanger on the inside must be pretty clean. And you have a great skill for cleaning burners. Your CO levels it produces must be pretty low maybe 4-5
@StuffStudier2 ай бұрын
One good thing I notice is that the water temperature signals on the water lines aren’t melted, which usually when it backdrafts those are deformed completely
@seantheenthusiast2 ай бұрын
(Assuming you are talking about the WH) Well, that's double wall around it So you can have something within six inches around it. The double wall doesn't get quite as hot as single wall.
@StuffStudier2 ай бұрын
@@seantheenthusiast I accidentally commented it since I clicked on the wrong video lol but yeah
@seantheenthusiast2 ай бұрын
The lines look like they are touching the flu pipe, but they're actually not. It's just a botched install from whoever did the first or second water heater install.
@StuffStudier2 ай бұрын
@@seantheenthusiast I know that, but if you look directly beside it on top of the water heater around each line you’ll see 2 colored plastic rings that melt when it backdrafts those are
@StuffStudier2 ай бұрын
@@seantheenthusiast Temps are starting to get pretty cold here I catch the heat running every morning now
@StuffStudier2 ай бұрын
That venting does not meet code. Water heater venting should never go in a downwards slope. My old water heater had that and my new water heaters venting is better and vents properly now. Could you make a video showing the full venting to where it goes out the chimney?
@seantheenthusiast2 ай бұрын
The venting is not part of my work. I just reused it. I'm not really sure if it was the person doing the 2008 install or if that's the original venting. I'll show you though once Everyone's asleep.
@seantheenthusiast2 ай бұрын
kzbin.infoel2WNfqNZ6A?feature=share
@StuffStudier2 ай бұрын
Love the way these units are designed. Very easy to work on
@seantheenthusiast2 ай бұрын
I agree
@EMMASHEALER2 ай бұрын
Can you tell me which wire goes to which terminal on the detector? Please
@seantheenthusiast2 ай бұрын
Sure! Are you installing one or multiple detectors on the same circuit? The reason why I'm asking this because The wiring configuration may be different if you're installing more than one.
@EMMASHEALER2 ай бұрын
I am installing one detector
@EMMASHEALER2 ай бұрын
I have the exact same detector as you installed.
@seantheenthusiast2 ай бұрын
Okay so the two terminals wires on the unit negative and positive will connect to the aux power output terminals on the panel. Terminal 4 (on the alarm panel) is the negative, and terminal 5 is the positive. The other 2 Two wires Are for the zone You're gonna be connecting it to. The C terminal on the detector which is common is gonna go to the hi side of the zone (on the panel). The NO terminal on the detector Which stands for normally open will go to the low side (on the panel). For example: If I were to connect this detector to zone 6, The low side will be terminal 16 while the hi side will be 17. You'll need to put resistors on the circuit for it to work properly. What I did is I Spliced the wire into the high side of the zone And then I put a crimp connector on the end of the wire, Then I put A resistor on the end of that crimp connector and connected it to the terminal on the board. Then I put a second resistor on the detector, That Resistor goes to NO and T which is trouble. I hope this helps you out. I Can post a photo on my youtube page if you need further help.
@knivesh.9582 ай бұрын
Lifesaver thank you
@TheRealHalt3 ай бұрын
😢 I miss the vortex
@seantheenthusiast3 ай бұрын
Me too
@gamingdestruction29184 ай бұрын
I just expected thr tabs not to load and it'll just say something but it is removed and maybe should of saw that coming, but it looks the same as it always does when your offline. I forgot taking away the market would take away most of the dashboard.
@seantheenthusiast4 ай бұрын
Yeah that's what I thought too but I didn't expect them to update the dashboard to look like that
@gamingdestruction29184 ай бұрын
@@seantheenthusiast yeah exactly, I'm still., happy online multilplayer can still works, as longs as the company supports it. Wish things lasted forever but never do.
@incogry4 ай бұрын
I like it👈, that the same amount of pulls it takes to start my trimmer.
@seantheenthusiast4 ай бұрын
Yeah it's been the best trimmer I've ever owned, I readjusted the carburetor again and sometimes it'll start on the first pull.
@seantheenthusiast4 ай бұрын
You got the same one too?
@lukevirgil11484 ай бұрын
the 360 store should have stayed considering all things are going digital and also streaming
@seantheenthusiast4 ай бұрын
Well the problem with that is the sales would eventually decline so they would have to shut it down anyways. I just wish they would give you the option to switch dashboard versions at least. That would be awesome!
@AndersonHobbyBoy4 ай бұрын
I also like elevators
@seantheenthusiast4 ай бұрын
Same
@georgemanley64214 ай бұрын
I had a 4 stroke verison of that weed trimmer and it was a piece of junk i even ran ethonel free gas in and had nothing but problems
@seantheenthusiast4 ай бұрын
Yeah I agree, I think all MTD trimmers are worthless when it comes to selling them too because once you buy one brand new you're kind of stuck with it unless you throw it in the garbage, or sell it for free or at a low price. It was very difficult to sell this one because everybody knows to stay away from these trimmers. I had another MTD trimmer that was older, and it was becoming expensive to keep it alive, so I gave it away instead of selling it because I knew that it was worthless at that point. I have since got myself an older Echo trimmer, and I love it! 👍
SADLY IT SOUNDS LIKE A MIX BETWEEN THE ELDORADO AND ESCALADE FROM FH3!!😢😢
@StuffStudier4 ай бұрын
Love that blower sound! Great filter too
@seantheenthusiast4 ай бұрын
Yeah so far the expensive filter is holding up. A little foam came off on the edge but it's doing alright 👍
@StuffStudier4 ай бұрын
@@seantheenthusiast The amount of discoloration on my heat exchanger though makes me worried about the air flow to it, I feel it’s not normal for it to have that much discoloration already
@seantheenthusiast4 ай бұрын
Well like I said before, the blower speed is programmable so you can change it if that makes you feel better
@StuffStudier4 ай бұрын
@@seantheenthusiast I just don’t understand why it would be incorrectly set from the factory. What do you think of the amount of discoloration and stress marks seen on my heat exchanger?
@seantheenthusiast4 ай бұрын
Each house is different, so sometimes you need to set it to a different speed to get the most out of your furnace. Now, unless the heat exchanger is burnt, I wouldn't be worried too much about it. What does it look like now? Can you post a new photo of it?
@StuffStudier4 ай бұрын
I don’t know what it is about old trane blower motors starting up but it’s so nostalgic when I used to have the trane during heating season
@seantheenthusiast4 ай бұрын
PSCs for life 👍
@StuffStudier4 ай бұрын
@@seantheenthusiast If my motor ever went out, I would probably use a ECM to PSC modification on it, since i’m pretty sure it’s possible with an additional PCM board kit
@seantheenthusiast4 ай бұрын
Yeah Quik Products sells a kit you can get for 20 bucks
@hoplabobla4 ай бұрын
R.I.P 😢
@seantheenthusiast4 ай бұрын
RIP
@StuffStudier4 ай бұрын
Dang, we had a tornado warning a month ago, it was crazy outside!
@seantheenthusiast4 ай бұрын
Did you guys have a real tornado rip through your neighborhood?
@StuffStudier4 ай бұрын
@@seantheenthusiast Nah, but it was crazy
@seantheenthusiast4 ай бұрын
Windy?
@StuffStudier4 ай бұрын
@@seantheenthusiast Very
@seantheenthusiast4 ай бұрын
That's crazy, normally it's quiet over here when we get a tornado warning. At one time we did have a real tornado rip through our neighborhood at 2 in the morning and it was moving our patio stuff around. The wind was so loud I could not hear the sirens and we didn't have power until the next day. Surprisingly our house didn't take any damage at all!
@Bacon64-x2l4 ай бұрын
Thats awesome I love sirens
@seantheenthusiast4 ай бұрын
Yeah man it's a pretty cool system. Got a few 2001s, a fedelcode model 5, a sterling m10, and a 508
@Bacon64-x2l4 ай бұрын
@@seantheenthusiast hey this is axo btw on an alt
@StuffStudier4 ай бұрын
I was checking out some videos you posted and was wondering, how often does your heat come on and run for every average day during heating season? Mine comes on like every 15 minutes and runs for 5-10
@seantheenthusiast4 ай бұрын
That's roughly how often mine would run, 20 minutes or so
@seantheenthusiast4 ай бұрын
BTW I will not be replacing the draft motor this year. I lost my recent job again so I need to save my money I'm kinda being a cheapskate at this point. So far it sounds fine so I'm gonna leave it alone
@StuffStudier4 ай бұрын
@@seantheenthusiast Oh that’s sucks, sorry about that, but yeah as long as it’s going don’t replace it
@StuffStudier4 ай бұрын
@@seantheenthusiast Is it normal for a furnace like mine to already have the discoloration and stress marks?
@seantheenthusiast4 ай бұрын
Yeah that's normal, any furnace will do that
@CoachpriceT4 ай бұрын
Can y'all play online after the shutdown?
@seantheenthusiast4 ай бұрын
Yeah you can still play online, it's just the store that's gone
@JohnBoosh4 ай бұрын
The dashboard looks so empty now. It’s a sad day for Xbox
@seantheenthusiast4 ай бұрын
It is
@seantheenthusiast4 ай бұрын
I juat discovered that if you disconnect your 360 from the internet, you'll get the store tab back
@Felixeditz-f3s4 ай бұрын
@@seantheenthusiastwait does it work
@seantheenthusiast4 ай бұрын
It does but you can't go into the store when you're not connected, but when you reconnect the store tab disappears again, so I guess that's the only way to keep the store on your dashboard
@Felixeditz-f3s4 ай бұрын
@@seantheenthusiast oh ok
@DustyOrchid0574 ай бұрын
the xbox 360 looks different now because of the marketplace shutdown
@seantheenthusiast4 ай бұрын
Yeah it feels so empty now, I wish they gave you the option to switch dashboards at least
@DustyOrchid0574 ай бұрын
@@seantheenthusiasthey look on the bright side no clutter
@seantheenthusiast4 ай бұрын
That's true it does look a little more sleek
@unitedstatesofcolombia96944 ай бұрын
NOOOOOO AHHHH
@7Agamer_IR74 ай бұрын
Hey go and search spider man 3 game and gamer picture and let's see what you can find
@mohammedlking41844 ай бұрын
Hey i was wondering, can i play resident evil 5 or 6 with my friend? ( He with the ps3 and i with the 360)
@duckie85224 ай бұрын
Ps3 And XB360 unfortunately are not crossplay.
@mohammedlking41844 ай бұрын
@@duckie8522 thanks for the info budd
@duckie85224 ай бұрын
@@mohammedlking4184 no problem!
@SPCPinellas80355 ай бұрын
Do you plan on getting a new panel?
@seantheenthusiast5 ай бұрын
Nope, this is the last panel that this house will ever need unless it fails
@seantheenthusiast5 ай бұрын
I still have the original panel laying in my basement I might take it with me when I move out. The only problem is it only supports landline to communicate and nobody around me uses that technology anymore so the best I can do is use it as an offline system so where's the fun in that ya know? I could sell it too but I don't think I'm going to get a whole lot out of it because it's a 20-year-old panel
@SPCPinellas80355 ай бұрын
Yay a new test video!
@SPCPinellas80355 ай бұрын
The siren: "AAA HAHAHA"
@seantheenthusiast5 ай бұрын
This one hasn't sounded in 10 years so that's why it sounded like that, it sounds normal now.
@SPCPinellas80355 ай бұрын
Oh nice, my siren hasn't been sounded in over 13 years so it scared me when I actually set the panel off 😅 @seantheenthusiast9234
Nice is that a Chinese carb I have same one with Chinese carb that takes 4 pulls to start
@seantheenthusiast6 ай бұрын
Nope this is the oem carb on it. This is actually the second one that's on it, The original one had bad internal check valves on it, So It wouldn't work at all. This oem zama carburetor I bought for 40 bucks And with a little bit of tuning Has been running well ever since.
@itsbeatzz96 ай бұрын
Is it easy to pull I have same one and it is easy to pull I’m scared of it is worn
@seantheenthusiast6 ай бұрын
Yeah, this one's pretty easy to start, too. I guess if you're talking about compression, I mean you feel all of it when you pull on it slow. This one doesn't seem to be worn out, and it fires on the first pull almost every time.