I have a 24lb trolling motor and it says max draw is 20amps it should be fine to use with this box how it is yeah? Ill be swapping over the connection to a anderson plug on the trolling motor.. any other issues i have to look out for with having that box around salt water?
@ailurophileperson19 күн бұрын
@@bigdaddy4602 yes that should be fine. The box is good and will protect your battery in salt and fresh water. Cheers
@bigdaddy460219 күн бұрын
@ailurophileperson thank you for the reply it's appreciated... looking forward to being out on the water
@khuong1994Ай бұрын
awesome m8
@dalehatton6965Ай бұрын
How do you remove the second plate? 😆
@ailurophilepersonАй бұрын
You have to actually bend it a bit to get it out. When you put it back in you bend it back so it’s straight at the end. That’s the only way I could get it in and out of the smaller hole at the top.
@dalehatton6965Ай бұрын
@ailurophileperson Thank you, I ended up doing just that, with the help of frustration and a little bit of anger! 😆
@derekwiffen1115Ай бұрын
Interesting set up just looking at adding a motor to my kayak and the motor could also end up on my 3.6 m drift boat as well. Thinking I might also end up doing a trailer for the yak.
@joebaily37282 ай бұрын
Thanks for the video. This is exactly what I have been looking at. How does the SXW compare to the 24lb motor you had? I know the SXW is a bit heavier. Did it effect the balance of the kayak? Was also thinking of buying the same bracket. I have a K2F 1+1 kayak. Also, how does the battery monitor working on the SXW? I have a King lithium battery too, but not sure if the monitor on the battery box is accurate with lithium batteries. Cheers again.
@ailurophileperson2 ай бұрын
@@joebaily3728 thanks. I recently sold the kayak as I got a tinny now to take the family out. The 34 lbs motor does have more thrust but probably doesn’t make the kayak go much faster than the 24 lbs one. As you know the kayak doesn’t get on a plane so the maximum speed is limited. Also the SXW is heavier and does tilt the kayak to its side on maximum thrust. At lower speeds it’s okay. In retrospect I would’ve gone for the 24 lbs one with this particular transom mount that I’ve shown in this video. I think the 24 lbs is ideal for a kayak in terms of its weight and speed generated. The battery box is reasonably accurate, only 0.1 Volts off from the reading on the actual motor itself. Good luck and enjoy 👍
@fastzy19622 ай бұрын
I nead new end rubber were do yo get them from
@ailurophileperson2 ай бұрын
@@fastzy1962 I’d try a wrecking yard
@deansaffrett82132 ай бұрын
This was the exact battery and box i was going to purchase. This video is perfect information on upgrades i need to do. Could you run a fish finder off the box at the same time ?
@ailurophileperson2 ай бұрын
@@deansaffrett8213 thanks. You should be able to. You can just connect it to the other Anderson plug or in any other way you’d like.
@CitizenZ98232 ай бұрын
So….did your jetski go back on and could you open the tailgate all the way? That is all we need to know?
@ailurophileperson2 ай бұрын
@@CitizenZ9823 it sure did 🙂
@mendoza46693 ай бұрын
I hear there is someone in the background that does most of your work like most KZbin channels is that true?
@ailurophileperson3 ай бұрын
@@mendoza4669 but of course.. I’ve got my team of cameramen, producers, make up artists.. why ponder dear fella.. 😜
@niloykesslar24473 ай бұрын
Does it show speed alerts?
@ailurophileperson3 ай бұрын
@@niloykesslar2447 yes
@niloykesslar24473 ай бұрын
@@ailurophileperson Thanks, does it give you any instant warning when you go over the speed limit? How well does the speed limit alert work in Melbourne? I mainly brought it to avoid any speeding fines.
@ailurophileperson3 ай бұрын
@@niloykesslar2447 it alerts you about the fixed cameras and when you are nearing them and crossing the speed limits. Should work well I’d think. Works okay here in Brisbane.
@graphicventures3 ай бұрын
Hi, the one i have has 3 pipes!
@Angus123374 ай бұрын
Hi, how do you get the over rides off and on? Your video doesnt show how this is done?
@mscwdenari4 ай бұрын
Thanks!
@mscwdenari4 ай бұрын
Thanks for such a quick reply! Unfortunately, I can’t get it back to that point as it always tries to connect to internet and there’s not much help out there!
@ailurophileperson4 ай бұрын
That’s no good. Hope you can return it for a refund. Might be easier to just use a standard reverse camera and point it all the way down while hitching to the trailer. All the best 👍
@mscwdenari4 ай бұрын
I bought this same camera and for the life of me I can’t get it to work! It wants me to connect to the internet but if it’s a backup camera I obviously won’t have Wi-Fi in the car (I’m assuming you’re using Bluetooth from the camera to the app?). Any feedback you have would be helpfully! Thanks!
@ailurophileperson4 ай бұрын
I think out of memory you have to skip that step where it is prompting you to connect to the wifi. I was able to do that with the app I had for this particular camera. After skipping that step I was able to set it up. Hope that helps. Cheers
@brentonmiddlemiss78735 ай бұрын
Great presentation. you made it look easy
@tracypowell24595 ай бұрын
I wonder did you stay with this set up? You have no access to the underfloor area where the third row seats are / were? Also you can’t put anything under the fridge and presumably don’t put stuff on top so a lot of wasted space? I am also interested to know if the 12 v plug worked or tripped? I had to get a beefed up socket with a higher value fuse to run my fridge. I have an NW and I remade the rear floor panels to access the under floor area and also originally made a platform for the whole cargo area and mounted the fridge and slide on the top, later I modified this to one drawer on the left with the fridge on it. I use a bike rack sometimes and the access to the right is very limited so I keep the drawer on the left. Thanks for your video.
@ailurophileperson4 ай бұрын
Hi Tracy sorry for the late reply. Had been away travelling. Yes the access to the underfloor area is an issue but I don’t normally store much in there as I put most of my 4wd stuff in the drawer I put at the back. I only really use this set up when going on a road trip with family. Generally keep the fridge at home unplugged. I could put stuff on top of the fridge though. It is relatively sturdy and didn’t have any problems with it. The 12V socket worked fine with the amp draw for this fridge and I didn’t have any problems with it. I usually connect it to a 120AH Lithium deep cycle battery though that I have in a battery box and charged with the solar panel that I have mounted at the top. Have never run out of the battery and the fridge has run continuously for a three week round trip that we did down to South Australia from Queensland. Even while parked undercover or at night. The fridge was connected to the battery and ran continuously. Hope you’re liking your set up. I’ve seen people use hinges etc to be able to access the underfloor area. Cheers
@gregrat61926 ай бұрын
Position your camera.
@sldrose6 ай бұрын
Thanks for the video. I’m having the same issue with the kings battery box being 30a and I keep blowing fuses. Thanks. I’ll need to rewire
@ailurophileperson6 ай бұрын
You’re most welcome. Hope it all goes smoothly once you have rewired it. Cheers
@shane0nz7 ай бұрын
Hi The safety camera function you mentioned is that a speed camera? Thanks for the review
@ailurophileperson7 ай бұрын
It tells you the speed and also warns you when you are approaching fixed speed traffic cameras that it has stored in its database.
@evanmurphy21657 ай бұрын
The "hole" you are thinking drilling is a spot weld - do not drill those out for structural integrity.
@tomwang26688 ай бұрын
Didn't show how
@tomwang26688 ай бұрын
Thanks
@LawalOlalekan-x3d9 ай бұрын
Front break disc
@borgfishlures9 ай бұрын
How’s the kings battery perform? I see that the 34lb is recommended to have a 60ah battery, but 120ah will be longer lasting I assume.
@ailurophileperson9 ай бұрын
Actually I haven’t been out on the water yet with it. I won’t go with 60ah especially if it’s AGM or not a reputable brand lithium. I’ve been out a few times with my previous 24lb motor and the 120ah Lithium and it’s lasted me the whole day while still staying around 13 Volts. So really impressed with it
@21leemo9 ай бұрын
It’s legal to remove the seats you just have to remove the seatbelts also
@legargeananatole377210 ай бұрын
Hi mate, I have exactly the same problem, I want to fix the frame of the drawer in my pajero but the bolts furnished doesn’t fit in the hole of the car, how did you succeed to make new holes and screw M10 bolts in it ?
@ailurophileperson10 ай бұрын
Hi I just drilled into the base and secured with bolts and nuts where I could. The weight of the drawer with the side anchor prevents it from moving as well
@legargeananatole377210 ай бұрын
@@ailurophileperson thanks for the answer, how did you succeed to access under the base to screw the nuts on the bolts ?
@ailurophileperson10 ай бұрын
@@legargeananatole3772 I have to actually put it back in shortly after removing it earlier for extra gear. Shall endeavour to make another video then to show. Cheers
@ahmedabdelfattah873710 ай бұрын
I can't check the short links
@coopermatthews24319 ай бұрын
Same
@bikesandoutdoors11 ай бұрын
Cheers mate thanks for showing the wheel nut removal tool, didn’t know they existed. It’s a great idea and I’m getting one today on clearance $32.00 👍
@IshidaHagoromo Жыл бұрын
can i ask sir i miss another harness i dont know where it location
@ailurophileperson Жыл бұрын
Hmm sorry am not familiar with any other harnesses than these. Might be an aftermarket/custom item?
@mattheww1779 Жыл бұрын
what sd card capacity do u recommend?
@ailurophileperson Жыл бұрын
I use an 8gb one but you could probably get away with a smaller capacity. Most of these dash cams just overwrite the old videos unless you save them. So memory is usually not an issue. Cheers
@WORLDOFWAR10 Жыл бұрын
Amazing video 🎉👍🏼👍🏼 i finally came to a video so useful. you did not skip any steps and recorded it in one video amazing will be doing this tomorrow :)
@yunk9 Жыл бұрын
Can you fit a 33" on this set up. Good video.
@ailurophileperson Жыл бұрын
Haven’t tried but I don’t see why not. The plate seems quite sturdy. Thanks
@rezosful20727 ай бұрын
I m tryng with 32.5" (265 70 18) the problem is always the same with gen4. The "cardine in italiano" i don t now the english word, hit the wheel😢
@patricktaylor1399 Жыл бұрын
What's the brake light's code or number?
@ailurophileperson Жыл бұрын
It’s a T20 bulb
@robbiecryer Жыл бұрын
Thanks for sharing 👍😎
@robbiecryer Жыл бұрын
Thanks for sharing 👍😎
@nassermn6542 Жыл бұрын
Thank you alot, I'm standing at my pajero right now, and got ur simple and unique explanation helped me. ❤
@robbiecryer Жыл бұрын
Thanks for sharing 👍😎
@larrykavanagh5197 Жыл бұрын
I would always use new pads with new discs. The old pads would be worn to the shape of the old discs and would cause uneven wear on the new discs.
@robbiecryer Жыл бұрын
Thanks for sharing 👍😎
@robbiecryer Жыл бұрын
Thanks for sharing 👍
@mendoza4669 Жыл бұрын
Looks like the Pajero has a lot of common problems thanks for the vid looks like a car to steer clear of 👍
@drugofanation4 ай бұрын
Not at all. They are brilliant cars. Definitely good value especially compared to Prado of similar age and use.
@robbiecryer Жыл бұрын
You need to speak a lot louderYou keep fading in and out Thanks for sharing
@robbiecryer Жыл бұрын
Thanks for sharing. Just to let you know That red light in the middle is not a brake light Its a fog light, the switch is on the right hand side above you knee cheers
@ailurophileperson Жыл бұрын
Yes true. I remember that now. Have hardly ever had to use it actually. Thinking about replacing it with a reverse lamp
@rezosful2072 Жыл бұрын
Otherwise, all come from the same factory. Only change the mark
Hey, was wondering the sizes of the bolts for the brackets and attaching the bullbar?
@ailurophileperson Жыл бұрын
Sorry for the late reply Liam. M10 bolts for the chassis brackets and M12 for the bullbar. Cheers
@CharlieRaines-f1x Жыл бұрын
Do you know what size the three stock bolts that were removed are (at 5:33)? I'm in the process of reversing a lift (to try fit a larger tyre in the case) and the previous owner must have thrown them out.
@ailurophileperson Жыл бұрын
Sorry for the late reply Charlie. I’m away right now but have the bolts still sitting at home. Will have a look once I return from the trip and advise. Cheers
@robbiecryer Жыл бұрын
Thanks for sharing. What yr is mitsubshi pajero. Thanks in advance. Cheers
@ailurophileperson Жыл бұрын
It’s a 2007 NS Pajero Exceed
@mendoza4669 Жыл бұрын
I have an alert ready for the Pajero motor complete change😆 I imagine it’s just a matter of time