Why we don't the MacAdams equ.? Re>30000 so I think that it should be f=0.184Re^(-0.2) am I correct?

why we took iteration

Thank You Sir

Dear Sir, This series of Equipment Design and Piping Engineering very helpful for everyone who wants to do the career in Piping Engineering, Thank you Sir,

Sir i am in design proffesion and in industry they save the money on materials which is below thickness calculation, so how to calculate thickness for such conditions

How to contact with you

crystal clear explanation sir 🙏 can u provide us the presentation of the whole course which will be very useful to us ..take it as a request pl

Siir Can you guide me, how to design a skirt with large opening. While designing in PV Elite software, there is warning for radial buckling, and provision of frame may prevent this. But how to design the frame.? Opening is 32". Vessel is 5.8m dia x height 35m, weight. Weight 162m

🙏❤

Sir please share your contact number

Sir what is p in this formula

❤

❤

Sir but which supports their used like shoe , hanger like that

Can it only be used for parts with thickness? I have a pressure vessel that has some high-stress distribution longitudinal to the vessel due to seismic loading. I am using shell elements in Nastran.

Thank you very much sir..❤

Very helpfull❤

Sir pressure drop calculations video not clearly visible plese can u upload again

Why long radius elbow account in the pressure drop calculation

Could you please explain how to do the screening for fatigue?

Thank you so much sir

How to do such complex calculations, such as for multiphase , non-isothermal , compressible ..etc? Can you list some documents that help to do so?

Could you name the references for the tables ,please?

Sir In B 16.9 1.3 Fabricated fittings Fabricated lap joint stub ends are exempt from circumferntial and intersection welds restrictions. Please tell what is fabricated lap joint stub ends??

Hello Sir, Thanks for your tutorials. I was following this example using asme code but my results are not matching the results given in book for elastic analysis. And for that reason, i am getting wrong results for elastic plastic analysis and protection against local failure. If you have the exact drawing codes or dimensions that you have used for your analysis and if you could share it, then it will be really helpful.

Thank you very much sir….. personalities like you are the real nation builder.

Sir,How we avoid crevice corrosion? or any method to control crevice corrosion?

Dear why we multiplied by 12 in conversion from in to m? Doesn’t multiply by 0.0254 was enough?

Can I use same for pressure drop in ducts from blower to motor

Excuse me sir. where do we get the permissimble stress vaalue for each skirt, base plate, and bolt

sir local primary membrane stresses is greater than allowable stress why and why material doesnt break however it reach allowable stress value or even more than that

Dear sir, can you guide about leg support also?

Thank you Sir, It is very helpful. I was preparing for a job interview and I didn't know anything about fracture mechanics. with these videos, I was able to know basics of fracture mechanics. Thank you

Where can i found compressive strength of sa 387 11 2

Dear sir, I like the video I wish to know about What about compressor ring calculation? And gusset calculation? Double gusset support calculation. ? What about pcd of bolting and pitch between two bolts?

Sir,Do we need to consider the elevations in the middle sections ?why are we considering only the inlet and outlet heights?

Sir can you please provide the excel sheet of support span and the catalouge for selection of spring hanger

Nice explanation sir and the way you correlate with practical examples is very good and easy to understand..thanks for sharing

Very nice explanation sir , thanks for uploading sir

Very informative sir

HELLO SIR, CAN YOU MAKE ONE VIDEO FOR PRESSURE DROP CALCULATION CONSIDERING EX- WITH CENTRIFUGAL PUMP, CONTROL VALVE AND FINAL IS STORAGE TANK... OR HEAT EXCHANGER....

Hello Sir, could you share the Ansys file with me. Thank you

your explanation is phenomenal.

Proud of you sir.

Very nicely explained.

The oxygen plant has 1000 LPM and the hospital has 750 beds. The pressure is 4 bar. Diametrical reductions are 12,15,22,28,35,42,54,76 and 108. All in mm.

Good evening Sir, kindly guide us on how to do line sizing for the Medical gas pipeline system of a hospital. The flow rate, diametrical, and length calculations.

Nice video!