6 жыл бұрын
6 жыл бұрын
6 жыл бұрын
6 жыл бұрын
6 жыл бұрын
Пікірлер
@JamesRothschild 9 күн бұрын
These nozzles, especially the drivers side (UK) seem to fail every 18 months or so. I wonder if the rubber/plastic wee value inside them are deforming with summer heat? until they block 😲
@dwinterx 9 күн бұрын
So far so good with the cheap replacements mentioned in the video, and I ended up with an extra set by accident. Whether I can find them when needed is the next challenge! 😃
@fuckingfuckfuckfuck 2 ай бұрын
One of the better video guides - thanks!
@87ryzo87 3 ай бұрын
Great video, thanks very much! Cost me less than a tenner and took under an hour to fix. Kia wanted £145 👍🏻
@dwinterx 3 ай бұрын
Glad you found it helpful, I still have the Sportage and the cheapo nozzles I fitted are still working fine! 😀 It would seem you can fit them without taking off a lot of bits I did, but it's not difficult and does allow you to check the lines aren't blocked etc..
@keithstorey4183 4 ай бұрын
Very helpful. Thank you from Canada
@dwinterx 4 ай бұрын
My sister lives there, glad you found it useful.
@Maixo 5 ай бұрын
What species of lobotomised orangutans design these car systems?? All this fuss to change a couple of plastic nozzles!
@l.m.1255 6 ай бұрын
Thanks for making this video
@FitnessPlanB 6 ай бұрын
You almost created more work for yourself
@dwinterx 3 ай бұрын
I think it's possible to do it without taking a lot of that stuff off, but good to check the pipes aren't loose / blocked elsewhere. Not like it's a long or complicated job to do though!
@user-mx5ek3fc9t 10 ай бұрын
I just followed this really informative video however my washer jets still didn’t work. The problem turned out to be black bacterial sludge in the reservoir. So a suggestion before taking the whole scuttle out to replace the jets is to disconnect the pipe that feeds into the scuttle to see if fluid is getting that far. I solved the sludge problem by syphoning out the fluid from the reservoir and filling it with water mixed with a cup full of bleach, and running this through the pump and pipe into a jug in the engine bay, and repeating this several times until maximum pressure was achieved, then reconnecting the pipe to the scuttle.
@dwinterx 10 ай бұрын
Great tip, thanks for posting it!
@bernardz27 6 ай бұрын
Awesome comment, I just followed ur advice and eventually got my issue sorted 👍
@darrenconlon4538 11 ай бұрын
Lol they just clip out. 🤣
@dwinterx 11 ай бұрын
As someone else has mentioned also, but it's certainly not clear that you won't pull the hose off at the back doing it that way. It's not like it takes long to take it apart, like 5mins, and then you can check for blockages elsewhere. I may well give it a try next time though.
@seanoconnor8416 7 ай бұрын
Hi, anyway of getting hose back on that way, hose after blowing off , spraying out through grid near it, could I fish out back out jet hole without taking all apart?
@seanoconnor8416 7 ай бұрын
Would be very hard to fish out I'd say through small jet hole, will I have to take a part
@runtothetrails Жыл бұрын
Nice one thanks for sharing 😊
@stevenunderwood. Жыл бұрын
Quicker way. Stanley blade under squirter Cut top off. Two small screw drivers push the plastiic clips in and pops the squirter out. Replace .10mins .max.
@runtothetrails Жыл бұрын
Just chop the tops off?
@bassdrum3351 Жыл бұрын
Hi, you're a star mate, the pipe had popped off my driver's side front jet, I watched your video and with a screwdriver, socket, a few drops of super-glue and double-sided tape it was sorted within an hour following your tips - BTW my car is a Kia Soul - Thank You!!
@dwinterx Жыл бұрын
Glad you found it useful. Sounds like the Soul must be similar in design then.
@jeffboardman197 Жыл бұрын
If you look at the replacement jets they clip in place by 2 tags front & back, To replace the jets all you have to do is remove the old ones by inserting a blade at the front of the jet to free the tag lifting the jet up & then the rear tag while keeping the front one up. Pull old jet off & replace , but you will need to test the tube is clear by operating the pump before fitting the new jet.
@dwinterx Жыл бұрын
Would certainly save a fair bit of time. I didn't mind taking it all apart so much though, as I found it useful to check the system wasn't blocked elsewhere.
@michaelharvey9555 Жыл бұрын
Changed both of my front nozzles today on my Sportage bought same ones as per your link and followed your instructions both working fine thanks again for your video a great help.
@michaelharvey9555 Жыл бұрын
Good video one of my jets not working properly (passenger side ) followed your link and they arrived today will follow your instructions my Sportage has only 9655 miles on I had to change the return valve in the rear wash at 2000 miles easy to do but they should be replaced by Kia my last sportage I had problem with the rear one also had four Kia’s now love them but washers not great.
@dwinterx Жыл бұрын
Yeah, I think it should definitely be a warranty fix in the first few years. Apparently some dealers will do this, a bit hit and miss!
@paulw2438 Жыл бұрын
Thanks for the upload, struggled to find a video for this. Cheers
@LadyViolatorUK1 6 жыл бұрын
oh my god...just seen this shocking xx
@guillermovil 6 жыл бұрын
Could you solve the problem? How?
@dwinterx 6 жыл бұрын
Hi, not yet no. It's been to the Citroen dealer 3 times, they recently replaced the telematics unit which controls the display but it's still doing the same thing. The car is with them again at the moment. Hopefully on the 3rd attempt they can fix it!
@tombegley3429 4 жыл бұрын
Hi. Just wondering did you manage to solve this problem? My Citroen is doing this as well, particularly when the weather is cold. Thanks
@dwinterx 4 жыл бұрын
@@tombegley3429 Sorry for the slow reply, didn't see a notification for this. I believe the final fix was replacing the screen. There was also a control unit inside the dash that was replaced, but this made no difference and the issue persisted. There was also a suggestion that having faulty leads plugged into the USB ports may contribute, but it definitely wasn't that in our case. Luckily the work we had done to fix it was covered under a dealer warranty. Was about £3000 pounds worth.