Fantastic video. I just ordered one of these to demonstrate engine technology in my TV science show.

Thank you !!! 👍👍

It just happen to me i used thread locker blue shit i learn this in school

How do you put one in?

Would a bad blower motor cause the check engine light to come on?

Is there a certain way the camshaft lobes have to be?

THANK U BRO🙌🏾

Good video. Thank you. I hit subscribe.

You stole this from Wham baam

Bro take this video down if you gonna do a o2 sensor do it correctly and stop tryna waste people time with the dumbest and false information

Stuck valve

What year was this model? I have a 2005

Perfect! Thanks! I used LED lamps. No polarity marks. But there is a tiny capacitor with a + on it, that is the side I plugged into the colored wire side of the socket. Worked on first try.

You didn’t even look at the foam filter?

this does work, but if you use a fuse terminal connected to acc on ignition switch pump will run while listening to radio. Find a 20a fuse that is only active in run position. my 2011 ram has a 20a fuse for glow plugs (not a diesel), heated seats, and rear wiper which is not used. this was the perfect choice. good luck.

No they just look stupid, a Cybertruck is lucky to look like such a legend

Do you know where I can see video of how the driver's side CV axel is replaced in a 2007 es350? Shop down the street did it, and having big issues immediately afterward with alignment(?) and want to know how this happened and how to proceed.

Just tried this before dropping the tank and pulling the pump. Cranked right up. Bro THANK YOU. just saved us 300$ and a days worth of work .. liked and subscribed 🙏🤘

What does that mean? Head gasket?

Great video. Found a dead mouse in mine too!

Hahaha yeah slick how many hours did this 4 min clip take, real time. Plus after seeing your gloves I can only imagine how my long beautiful nails are going to end up😢. Hug's Emily 🤗

Great video!,,I tried hours using that tool smh didn’t work. However, you can half way loosen the nut and press down on the wipe as if you giving it CPR “the part of the wipe where it’s joined” press that a few times and then remove the nut and pull the wiper it come right off I swear on that save your mental patience! 2014 TDi VW, dealer motor cost 336$

i have same motor with a cold start timing chain rattle, even after replacing the chain /tensioners/and phasers... im thinking mayby oil pump? i even replaced the exhaust ocv, still waiting on the intake ont to come in the mail, i also get a little like timing chain tick at idle

Word of caution to anyone needing to do this job. Take the old one out before ordering a new one. Went to do the job, found a dead mouse stuck in the old blower motor. Took the mouse out, screwed it back in and it works fine. 😂 Anybody want to buy a blower motor for an '06 Jeep Commander? 😂 In all seriousness, this video was indeed helpful and Did help me fix my problem, thanks!

It would be great if you explaoned what you were doing start to finish.

Thanks for this upload and explaining the troubleshooting.

thanks

ماهو الفرق بين ١.٨ و ٢.٠ فى ماكينة النترا ٢٠١٦

Thanks

How long before the old oil stops burning off?

Thanks a million dude! I do tech support for an older lady sometimes and her 2006 model did this after her battery died(charged it and took care of that too). Got her radio fixed about an hour ago thanks to this!

thanks for posting this video.

do you add PAGoil or just recharge the freon? thank you.

That Idiot In Cars😂

I just have 1 question, would something like this have anything to do with my 07' f150 not cooling when stopped or idling ? Last year, everything was fine, this year Ive cleaned the shit out my condensor & radiator, and piece of shot truck still spitting me hot air at idle or stopped.

This might be a stupid question.... but my ram 1500 appears to have mini fuses... and this bypass has much wider prongs(and doesn't fit). Am I missing something?

The relay is integrated into the fuse block (Called TiPM). There is a circuit board inside of fuse block that the relay is soldered into. It’s not part of the fuel pump. Power is going from the relay to the fuse then to the fuel pump. But the relay is not allowing the current flow. You can replace the relay but it has to be soldered into tipm.

Wow, you don’t even torque it down to factory specifications.

That's pure junk, right down to the RTV. I can smell the Chinesium from here... You couldn't pay me enough to install one of these. My sanity is priceless.

do you know if the same procedure can done for 2006 toyota avalon?

seemed kind of rough on the extraction of the fan unit, wouldn't it be better to remove the radiator hose first?

Presente, aprendizaje de mecánica automotriz, gracias por compartir, saludos desde Navojoa Sonora México 🎉

Thank you sir very helpful!

It's so hard to find an oil pan gasket seal for this car😢

Pull the steering wheel really hard to left and hold. Try to turn the key. Does key turn? Try to the right. Worked for me. I know tumblers can fall and ruin the lock, but ive had this happen to me several times, in different vehicles and it always worked. The keylock apparatus was just pinched by the pressure of the steering wheel.

8mm bolts. Phillips head screwdriver for just the module.

It was too fast

It too fast

It too fast

We got it done in our cousin's 2007 Jeep Commander Limited today June 26, 2024. The only thing that almost confused us was that we had to be removed and installed blower that sits inside the outer cover that has it's own 3 screws the look exactly like the ones on the blower. There is no need to disconnect or remove the frame, just the three screws on the blower itself, but we got it done. Thank you for your video it was a great help.