Thanks

I have a Yongnuo 560-iv that has suddenly stopped working. It's less than a year old. I switch it on. The pilot light goes green, but it doesn't turn red as it should. It just stays green. When I press the light to test the flash, it doesn't go off. After about 30 seconds, the unit starts beeping, the display clears apart from a flashing symbol for empty battery. Then it goes off altogether. The batteries are fully charged Panasonic Enerloops (when I take them out and put them in other Yongnuo units, they work fine). If I simply open the battery cover, and close it again...the unit switches on, and goes through the same sequence I've outlined above. What's the issue here? Any help would be really appreciated.

my question is when I am turning my speed light into 1/128 mood and 1/1 the light won't change .....do you know why ?

Is it hard to get to the on/off switch? My on/off switch on the Yongnuo 600EX-RT (for Canon models) is very loose and easily can move accidentally turning the speedlite off during a shoot. It will actually turn past the full on and off positions. It was in my case as a backup flash so not even sure how this happened. Thanks. Hoping you have a suggestion. Philip PS. I see now your on/off switch is different then my Yongnuo model for Canon. Mine has a 3 way switch. Off-Lock-On positions. (It's more of a rotary switch). You'd have to look at a photo of a Canon model to see what I mean. Model 600EX-RT.

Thank you I have a YN 685 and it is helpful to watch

Lovely informative video. I have a Canon 500d & Youngnou 568exii ETTL speed lite. I want to use the speed lite off camera. Do I need 2 of yn622c or one yn622c & a yn622 tx also ?

non c'è la traduzione in italiano ?

Hello I had the same problem, my flash fell off the tripod and the batteries do not make contact with the battery door In your video I can not see what was the solution you applied. Did you change the battery compartment or applied another solution? Thank you!

Not working for me with 580EX II as shown above. 580 does not follow settings, does flash only at full power. I guess I am returning this product.

Thanks!

how do you get the convayer belts

Thanks for this video! Thanks to you I repaired my 568EX today and will have what I need for my shoot tomorrow! You are the man!

My top in-built small plastic diffuser got broke by falling on the ground. Only one lock got broken out of two. I am not able to use inbuilt bounce card as it doesn't stay there and comes out. What will be the solution for that? Any suggestion advice would be helpful

Unfortunately my YN565EX also has felt on the floor and battery cover is damaged. Reflection board and wide angle diffuser felt out from their compartment. I manage to find spare battery cover but have problem how to reach inside the diffuser compartment. It is over flash head and seems separated, but I am afraid to employ force to detach it by screwdriver or knife. Do you know what is the right way to remove this cover. Thank you.

My unit Yongnuo 568EX III makes a strange noise for exactly 20 seconds after being fired, like static, crackling electricity inside the bottom part of the flash. Anybody else experienced this? Is that normal? Thanks everyone

Hello, I just received YN622C-TX and Yn622CII. I am trying to control my canon speed light 580EXii as you showed in VDO but it is not working. it is flashing remotely but i cannot change the power or can do any control remotely. Please help

Thanks! Nice video I wish you would've shown how you were able to lift up the tension springs since it's such a tight space.

Hello! I have a set of this flash radio, 2 Yn 622C and a TX! I use with two Canon 580 EX II flash. However with one of the flashes I can not make any of the settings (mode, power, zoom) remotely, although I can make this flash shoot. The other flash works normally and another YN600 EX RT flash also operates normally. Can you tell me what happens? Thank you!

Great video. Similar to what happened to me

best mod

I have got the mod installed but cannot find a way to connect it to the front of my Styre tractor.

MUCHAS GRACIAS, TENIA EL MISMO PROBLEMA Y LO ARREGLE GRACIAS AL TUTORIAL. FELICITACIONES

the 565 is crap never buy another one i didn't get whut i payed for

I think you mean "shoveling"

Will this work with the 600EX? I have been trying to figure this out with no luck.

Will it work with a Canon 580EX (first generation)?

Also you should not turn in real life with your bucket raised up all the way as all the weight will sway the tractor and affects the center of gravity

Why do you need like 3500lbs on the back of those little tractors for 1600litres of silage ?

My batteries dont get out much as yours, how did u fix that? When u take off the motherboard can u reach that small pushing things? I've managed to get them out through battery compartment but i wonder if i take out the motherboard could i push them more? :)

May yongnuo yn -568ex flash stacked in full power 1 / 1 can you show me in picture where is igbt of the flash t.y.

3:02 ... the take off doesent work on my speedlite 580ex II, one point are so fixed, but there are no more screws. Use canon glue? .. i dont want to break something. The Speedlite cost over 394 EUR on 2008. problem: leaked batteries... no more function... i will check. canon said 280 EUR for repair... not funny.

My life has just changed drastically. this IS *AWESOMEEEEE*

Hello there. I'm using Canon 5D Mark II (2). Haven't got any triggers and flashes yet. Wanna figure out what I need first. Can I use my body with these guys /YN-622C-TX and YN-622C/ and what flashes do I need to have to get all the options including I-TTL an HSS? YN speedlights or Canon ones? Thanks for the video and the possible answer in advance.

Sorry can you send me an hi-res pictures of the motherboard please?thank you

i copied rar file to mods folder inside ..didnt worked..also inside of it none another zip file as u said

I can't install it

Great video. I can not figure out for the life of me how to get my Canon 430ex ii to work with the yn-622c-tx trigger. Any thoughts?