😮 #8 & #9 🔥🔥🔥🔥

This is a great video. But i didnt get the last one . 90 degrees anywhere is just with the Dotted line?

Shit

if you want to scribe you use a dam divider scriber

Boş işcilik

My LG was slightly different. I had to remove a bottom plate over the speakers. But all the electronics were all the same. The WIFI module was exactly the same. Cleaned the dust out, and presto! It works perfectly. Thank you, sir!

Aren't you suposed to leave space?

WHY THE STUPID MUSIC ???

Is you whole family, friends and relatives commenting below to your bullshit fix?

Que liquido le pusiste alas baterías

😅😞

Very detailed. Great work.

My guy you’re the best!

Parke öyle sıfır döşenmez şişer kenarda en az 1 cm boşluk olması gerekiyor

I take it You did not have the manual on how to adjust the rip fence that came with the saw

I've seen some pointless hacks, but this is up there with the best of them.

Thank you

excellent, thank you

A quick tip on the router table. Do the end grain first. That way if there is any blow out the side pass will clean it up.

Literally pointless as the skirting would cover the gap which is required. Don't waste your time.

What’s the minimum thickness of the plywood that can be used?

😂😂😂

I have this exact saw! That’s tonight’s project sorted!

Cute toes

Ummm Ill take what is a base board for 200 please Alex😂

I think the baseboards would cover that, if not why not cut some of the drywall instead?

Qu3do peor

Flooring should not be attached to the wall. There should be a 1/4inch space.

I remember playing with something like this when I was a kid in the 60’s! 😊 Hard as hell to master.

Ne commencer jamais droit au mur 😂 un pièces droite n'existe pas 😂 et laisser jusqu'à 0.5cm 😂

I think it's a great idea but after you cut it you put spacers and that way when you start putting your other tiles it'd be easier and they don't separate

Good job

Sbagliato, va lasciato 8mm dal muro

I only use my to scrap concrete or ice

Whats that edge cutting tool called

Of course you don't need a gap for expansion 😂

I have a very old pros pro drop weight stringing machine. Is it possible to mount the wise 2086 on every base?

Get a push stick! Having your hands close to theblade like that is dangerous

lol! Omg!

Lame

Don't do this.

but youre going to put trim over that.

Thanks for this great videos Was without tv for 3 days ! Saved me a lots of trouble

Even in my lg tv sk7900 the pointer disapear and not working even many time i reset my tv butt problem is still same butt thanks alot this vedio help me i opne my tv cover and clean the same part carefully then restart tv i was shoked the problome gone ❤

That’s not how you do it, you need that 1/4 inch gap there.

Hi there,great video well instructed easy to follow,so did you set your charger to ordinary battery mode or 12.6v lithium battery to charge?

vasted wood, unstable structure!

Ya know.... a piece of baseboard would hide that gap anyway

Mine had the same problem..yet it was fairly clean..but there is a screen under the impellar Hydro turbine which requires cleaning with a tooth brush and dish soap..the area in which the fellow in this vid is pulling out debris is the impellar housing remove the 4 screws and you can gain access..simply unwind(unscrew) the impellar from the threaded shaft to expose the screen below..it's ridiculous how such a small part blockage can cause a complete shut down of the machine- my model is WDT750SAHZ0..note to remove the pump you must tip the pumps square side post out of it's rubber insulation slot at the bottom of the machine..turning it clock wise..I had a tough time turning it so used WD40 on the contact rim..also remove the interior wash screen first and also the pump power clip..the smaller other pump is for the machine draining only..push 3 of the mode buttons 3 times each consecutively a total of nine to enter the machine reset and cycle..the machine will cycle through for errors..and reset.

Mine was clean as well but can't get it back on properly so it doesn't leak