I have the same pool minus the little fishy pattern. What about putting Fix-A-Flat in there because my bottom ring is not working that good I don't know if I have that group but it's a thought and I wanted to ask another person but if I come fix it right in there or melt a tarp on the bottom of the swimming pool with a hot air gun? You think that would work?? Cuz I can't find a link on the bottom one to save my life and I'm sick of playing with it but my grandbaby has my heart so I'm trying to do the same thing that you are and also cussing too!!

How do you get money out of qsfledgervault

Thank you

Where's the link for the headlights with the harness already attached

I have one of these. Came here to see how to remove the steering wheel as the blades wont engage after sitting for a couple years. I went to fire it up and it started smoking. So I only can guess that mice got to the wires. I do love this tractor though! Its slow but it cuts! I just bought the 3 manuals for it.

Slicker than snot mannnn!😅

Hi , is your motherboard can continue running for a year?

Thanks man! Having this exact issue, our floor is massively unlevel but didn't realize that would be an issue. Really appreciate you including your full troubleshooting process. Seeing you do this start to finish saved me from having to test it out myself to confirm your findings. You're the hero we need :)

Unfortunately it’s best on concrete slab & place those rubber mats & place pool on top.

Roadbase as the base. Then 1” thick extended polystyrene then place your pool mat/cover down on top of the polystyrene. Then cut out where the pavers go and get pool noodles and cut them to size just to protect from the edges of the pavers. I used road base as a base cause it compacts better than sand plus it allows drainage without eroding the sand away from the edges. Idk people use sand so often. Yes it’s easier to level but it also washes out very easy and you end up in this situation.

Such a pleasant attitude about the whole thing.

Thks much

should've gone with the ED37-GL-200 bulbs, they do much better than the corncob bulbs

Thank you or your help with that same error code, it made my printer work again!

What is the diaphragm p/n? And my throttle lever is floppy - is a torsion spring missing? I believe it’s Tecumseh 630978 Diaphragm.

Use a 5 gallon bucket works for me.

Good video 👍👍👍👍

I have the same laptop but unfortunately it turned out defective. I changed it in the store, but the second one gave the same defect. At times the display flickered and gave a display driver error message. Under warranty, the motherboard was replaced several times, but the defect remained. Strange why the service techs only test it on games but not normal behavior. Finally, already out of warranty, I took it to another service for cleaning, and afterwards it got a thin vertical pink line on the display. Still, this is the laptop with the best image out of all the 10+ I've used, and it's not slow either - 4GB RAM 64bit Win 7. It still works but crashes.

Grommet

Damn, that looks great. Nice job!

What size is the orifice? I know the lp holes are .5 but what is the thread and size?

You inspired me to have several drinks before replacing my receiver on my fan thanks for the video

LOL. it's like driving a car and ran out of gas.

You're a good fil for helping out like that.

If the water low * light is on , where do you add water ? Thx

buddy what are you doing ? Get that bad cement out of there. You're beating the piss out of that machine !

Thank you. That was good info. Hope to see more.

Why does everyone seems to be making this set up much more difficult for themselves then it needs to be. Just cut the ground/soil where the bricks are going to be placed so they’re flush with the grass, then use a 4ft leveller from brick to brick, digging in the necessary depth on the higher ones to have the pool legs match the same hight. Put a think tarp, foam or carpet down and you’re good to go. You don’t need the sand, and you don’t need to remove the entire grass area. As long as the bricks/legs are all set to the same hight the pool will lay even because the weight of the water will flatten the ground down to the correct height. And the bottom is protected from any rocks (that will also compress into the ground due to the weight of the water) by the tarp, foam or rug.

holy f, the difference between cat5 and 5e very different. nice test sir

Thanks bro

Best mid aisle video before purchasing. Thank you sir.

The scraping sound with the fork...ahh *-*

Thanks so much. You did a good job. I got my actuator done in less than 2 hours, and everything works. Without your video, I wouldn't have known what i was up against or where to start. Thanks so much. Tom from Canada

Better than gas 🤣🤣think I'll stick with my Stihl ms 271

😵‍💫 no

lol. i remember this life. i use window units now hope your lifes improved too

3000 labor for a 250.00 pool? Lol

Footers??? Lol

Great product but if you ever have a fire get the hell out immediately as it is very toxic.

⁠ I was hoping you were just testing out the instructions. You showed everyone how bogus the instructions are. I don’t know why they have that formula when it never works out that way. I’ve mixed 1000s of bags with machine and by hand in different weather and I always had to hose it. That dry mix you had for 4 minutes was stressing me out!! lol

Michigan? All the signs are there. I usually put them over a tarp. Even with these pools small rocks and dragging it carelessly can puncture, but it's still better than the ones with the inflatable rings. Appreciate the post before I set mine up!

I've been using this unit ( 8000 but ) for years now using both cooling and dehumidifier ..Never had issues never needed a drain hose nor had the full light come on ..At 75 the compressor will hardly kick in ..that's why they they have up and down temp settings

I spent another 20 bucks for a propane torch just so i could do something worth while with this google crap. torch it.

Mine is gummed up on the rollers from the rubber on the barrels I cleaned them and adjusted the belt it’s not overloaded but today again the rollers were covered in rubber and just sanding the barrel down from the friction can I spray anything on the plastic roller covers? I think the sewing machine oil I used for oiling the bearings has made the rubber sticky and I can’t seem to figure out how to keep the shaft rollers and the barrels clean. Ugghh

I was wondering why the manual says not to use sand as ground base now I know why.

Anyone gets a hole in pool, use flex tape, you can go under water with it & tape the hole.

Would the pump work without a filter in it? I was trying out mine and it wasn't generating pressure.

Most likely the concrete blocks is what caused the tear.

😂

My white plastic screw is not there. After market canisters. 😵‍💫