🔔 Get your tools here: ✅ Multimeter: amzn.to/49VzOhh ✅ Transistors: amzn.to/463Hkpz ✅ Breadboard: amzn.to/3IrVg1X

Yes but my Fluke doesn't have that option. Thank you bot man.

Fish is laughing 😆

🔔 Get your tools here: ✅ Multimeter: amzn.to/48S1Ry8 ✅ Headlight bulb: amzn.to/3RXorPo

🔔 Get your tools here: ✅ Multimeter: amzn.to/48S1Ry8 ✅ 6V battery: amzn.to/4avSOTZ ✅ Breadboard: amzn.to/3IrVg1X ✅ Alligator clip: amzn.to/3sIL8O9

🔔 Get your tools here: ✅ Multimeter: amzn.to/48S1Ry8 ✅ Breadboard: amzn.to/3IrVg1X ✅ Alligator clip: amzn.to/3sIL8O9 ✅ Flashlight: amzn.to/4eQIXLt

🔔 Get your tools here: ✅ Multimeter: amzn.to/49VzOhh ✅ Inductors: amzn.to/4bxgSWM

And, you should show about measurement of the voltage drop/burden when measuring current with the multimeter...

Hey where can you buy those really thin probes I can’t find them.

You earned my sub when you mentioned and showed that current flows from negative to positive.

why infinity ohm on a cap? and first so low?

This guy is depressed.

Touching the leads makes no significant impact on the reading (typically a few ohms), as fingers are generally several hundred K-ohms. BUT.....as you will find out, when you touch the leads you can get shocked from the inductive kick-back.

🔔 Get your tools here: ✅ Multimeter: amzn.to/48S1Ry8 ✅ 9V battery: amzn.to/3Ts1BRd ✅ Breadboard: amzn.to/3IrVg1X ✅ Alligator clip: amzn.to/3sIL8O9

Is it possible to use the signal generator and oscilloscope at the same time with this device? On the one hand, should we apply the frequency device with the signal generator and on the other hand, see the result simultaneously with the oscilloscope?!

I understand the gloves - but what is the point of safety glasses?

Don't you need to give an auto ranging meter a moment to adjust and give a reading?

❤❤❤

I am the 3rd

amazing series. i added to playlist and take note for each video

Is the ceramic cartridge better than a glass version? Thank you

🔔 Get your tools here: ✅ Multimeter: amzn.to/48S1Ry8 ✅ Alligator clip: amzn.to/3sIL8O9 ✅ Breadboard and wires: amzn.to/3IrVg1X ✅ Lenovo Laptop: amzn.to/4eK0TqY

🔔 Get your tools here: ✅ Multimeter: amzn.to/48S1Ry8 ✅ APC UPS Battery Backup: amzn.to/4bllP4U

Excellent video explaining things in detail appreciate it

How do u discharge a capacitor from welding machine ?

🔔 Get your tools here: Amazon ✅ WEP 939D+ IV Soldering Station: amzn.to/4bbkHAJ ✅ Soldering Iron Tip Set: amzn.to/4ertMYR ✅ Solder Wire: amzn.to/4bYWejf WEP Tools ✅ WEP 939D+ IV Soldering Station: www.weptools.com/products/939d-soldering-station ✅ Soldering Iron Tip Set: www.weptools.com/products/900m-10-wep-soldering-iron-tip-set

You cant measure ac voltage in connected V dc source, display goes crazy, but when you change to mv dc all is ok, china manufacturers cant make a complete product, anyway 99% this is a very useable multimeter, way better than other china meters.

I wish there is video on how to tell between neutral and ground wires . Both will show 120/240 .

You have exact same multimeter as I do lmao.

K.I.S.S.

Good gravy... Don't forget to wear your protective equipment. Lol 🤣 We all know the danger of spark plug poisoning or the potential of spark plug juice to the eyes

Awesome. Can we check if it is cat6 or cat5e with a multimeter?

Shit my ground is live for some reason

Pff you are so slow that is annoying...

Quick and to the point, thanks

Appreciate.thanks

🔔 Get your tools here: ✅ Multimeter: amzn.to/48S1Ry8 ✅ Resistor: amzn.to/3RB11hT ✅ Alligator Clip: amzn.to/3sIL8O9 ✅ Breadboard and Electronic Kit: amzn.to/4awOSTF

🔔 Get your tools here: ✅ Multimeter: amzn.to/48S1Ry8 ✅ Resistor: amzn.to/3RB11hT ✅ Alligator Clip: amzn.to/3sIL8O9 ✅ Breadboard and Electronic Kit: amzn.to/4awOSTF

how many watts did you use on the 100ohms resistor? please reply thanks

Have to test the multimeter first. Get a beep and you know it’s good to go.

ITS BEST FOR THE BEGINNERS

Much Appreciated ❤

At time 1:55 it does matter how the leads go in.. the black lead needs to go in first to avoid any potential electric shock

🔔 Get your tools here: ✅ Multimeter: amzn.to/49VzOhh ✅ Resistor: amzn.to/3RB11hT ✅ Alligator Clip: amzn.to/3sIL8O9 ✅ Breadboard and Electronic Kit: amzn.to/4awOSTF

subWOOfer

5:30 you have damaged both, the board and the chip: the chip leg torned off by the pad on the mb and the mb trace stuck to the chip also torned. both are from the last 5 pins of the left side row.

Thanks, can I test the on/off function by connecting the other two pins to a 12 volt battery?

Thanks bro!

Should have shown a circuit that turns it ON in darkness............Z