I've cleared a half mile driveway with a Case 446 with a front mount blower. Four trips back and forth. Had a cab on it to make it bearable.

Very nice machine. Thanks for sharing

How do you price tractors I have quite a few wanted a good idea as of what they go for. Thanks

Your a lucky guy to find that unit !!!!

I'm jealous. Wish I had a loader like that on my 1250.

Cool machine , do you have to fix anything

Yessss needed this video! I want to.do this to my 1650. Pray for me

Jimmy,...that is a lot of dang snow!

Works like a dream!

Great video Jimmy! Glad too see that ol girl workin!

I got the Cub Cadet blower..do you prefer plowing over snow blowing?

I have one word for you: SNOWBLOWER. Try it. It's amazing. No need for all the backing up. Just blow it out of your immediate way. No need for moving it extra distance for next time, just clear your spot and you're done. Really a huge game changer.

Sure beats a shovel. Sometimes you have to live within your means. We can’t all afford a big blower, or plow.

I have a 782D, but my gas 782 makes for a much easier starting plow tractor. My diesel is a little worn out so it doesn't like any temps under about 50 degrees, needs lots of glow plug time. They are fun tractors though. I have probably plowed 8-10" at a time with mine and it works well. I have a lot of weight on it. Thanks for the video.

If that isn’t a waste of time, I don’t know what is. Put the lawnmower away for the winter and get a plow truck for a big driveway like that.

I need bigger tractor 8 ft wide blade😅😅

I'm downstate in Rockland County, and you have more snow on the ground in the video than we've had in 6 years. I've been waiting 11 years to get enough snow to try out the snowblower I found for my regular Cub. Down here 3 snow flakes is enough to close everything down.

Have a Cub Cadet 102 that has a QA36 Snowthrower (outboard chain) on it it has done snow duty for Me for more than 30 years looks like it Too, bought a 1650 in june it has a near mint QA36 on it (inboard chain) well other than the bearings so it is all set to go I hope, no snow here yet in southern Ontario, I also have a 1450 and I have used that same plow on it but it has for years just been for grass duty, the plow does have that advantage were gravel is concerned the snowthrower does not eat stones to well, there are times most times were the thrower is preffered! Hope that was only the fuel pump not a good time for troubles to occur! It is doing a great Job of that : )

My 1772 plows the snow great,lots of torque, we have no snow in Lockport, just green grass

wow, the 882 really has a lot of power! I'm really excited about my new 782D. I wish it would snow so I could try it out, but I live in the desert southwest. In the spring I can use it to plow all the sand off my driveway.

I'm wonder my 1864 is going to need a new fuel pump since it out of nowhere ran really rough the other day. Have fun with the snow!

Thanks for making this!

What I wouldn't do for a couple of those nice opposed Kohlers.

is the 782d dash the same as a regular 782 with the addition of the third 2" hole for the temp gage? and the hole for the glow plug indicator?

Mac, I picked up the valve but I need a cylinder , can you give me the dimensions or do you have one to sell?

hit it with a spray can of John Deere Green or Yellow...!

I just bought a 782D. Any thoughts of where radiator hoses are available from? Thanks!

I'd bought a 50c deck a few months ago off ebay local seller had come off a 82 series cub cadet. When i got it all the spindles where original and froze up under the cover was full of rusty dirt the tensioner was also froze i had stripped the deck down to the shell took the updated spindles and tensioner from a rotted out 44a deck threw them on the 50c and it currently resides under a cub cadet 1450. And the one thing that's always discarded is the deflector that bolts to the deck was still present on the 50c i got.

Just a tip keep the buffing pad flat if you use the edge of the pad it can dig in a lot more aggressively and in the sun you can see waves in what you buffed. This really applies to freshly painted panels as well!

Nice looking unit, I am looking to get one too!

I bought one of those Amazon carbs for my K321 and it was an absolute POS. It leaked like a sieve and nothing I did fixed it. I ended up getting one from I Save Tractors for 2 times the price and it works great.

You don't need to drill anything. That valve hangs just below the tank and the line crosses in front of the tank between the tank bracket and the tank. It doesn't go through the frame. I just did one of these last week.

I see you didn't get a set of those rearend brace kit for that tractor from Xtream motor works. They bolt that rear housing in the frame like traction bars and keep it from moving and the housing from breaking. Well worth the $100. The cheapest center housing that I've located was $500.

Should I have an air filter on that if you're going to run it while it's open and it's throwing that much dirt around it it just sucking that into the engine and grounding down the Walls of the piston and the valve seat

Mice can piss ya off

How many cc is that engine?

Wow, What a nice Cub!!!

AWESOME video!! Power steering, super steer axle, front ports, ultimate 782!!

I think that all of the KT17 Kohler engines have that surge. Or at least all of my KT17 engines did.

I can't get over the money people pay for this equipment and not take care of it. They need a push type mower to use for a few years then maybe they might get the idea to take better care of their ride? 😮

Great video, perform the same maintenance on my 782D

My cyclops has rubber boots around both ends of the driveshaft. Is it the same as this underneath?

So I picked up the dual valve today and need a cylinder for the power angle. Do you have one for sale or could you tell what diameter and stroke length I need to duplicate yours? I will be good to go once I get the cylinder Thanks for the video !

I have a 109 hydro like this and out of 50 tractors, it's my favorite!

I have both a 44A and a 44C mower decks and I definitely like having the two wheels mounted at the rear of the mower deck in addition to the wheels mounted at the front of the mower deck over the 44A mower deck with the 2 wheels and the skids. The skids have the tendency to dig in where the wheels roll over the surface obviously. If I ever find a trashed 44C deck with good anti-scalp wheel brackets, I would love to convert my A deck into a C deck. I also entertained the thought of shaping 1/4 to 3/8 inch flat steel around the bottom of the mower deck like the newer Cub Cadet fabricated mower decks have nowadays. I had lots of practice and lots of experience repairing the mowing equipment while I was still working with the equipment section of the highway department. The right of way mowing was very brutal to the blades and driveline of the mowing equipment.

I like the "Power Stroke" sticker on the hood.

the 782d I just bought shows 1010 hours. Is that considered a lot? My 1450 and 982 both have about 500.

If it needs few parts toss them in and keep it whole but obviously it's your call neat machine. I have a couple 2182's and just put a d662 in the one but I always wondered how they had the fan off the rear of the engine didn't know there was a second belt setup and the coolant lines running under the motor it's pretty neat. Do you know is the rads get clogged up easy on those machines or they stay pretty clean?