7 ай бұрын
8 ай бұрын
Пікірлер
@AbeLincoln-f5v 21 сағат бұрын
Beautiful video! I was hoping to find a video of the location of the fuel pump! I looked in channel but no luck.... Where can i find that relay ? Thank you!
@camaromodschannel 19 сағат бұрын
What year your car ss or v6? Thanks
@АлександрАлександр-я7ы 3 күн бұрын
Дичь какая то
@camaromodschannel 2 күн бұрын
thanks
@jdmorge 4 күн бұрын
I recently got codes p0340 p0018 & p0019 some shop said timing chain job I don’t hear any weird engine noise or rattle, could it be just the cam sensors and vvt’s? Car turns on fine rpm’s don’t fluctuate crazy
@camaromodschannel 4 күн бұрын
Yes, sorry looking like a timming chains job, with the p0018,and p0019 cam shaft position sensor is not in the correct position. How many miles on the engine? Thanks
@4bdn_ 5 күн бұрын
Hi. Im in California and it wont pass smog due to “modified software” even after it was tuned back to stock. Will this method work?
@camaromodschannel 5 күн бұрын
Yes, if you tune it to stock, then resetting wouldn't hurt to try. Thanks
@4bdn_ 4 күн бұрын
@ thanks for the response. Any idea if i have to drive it a certain amount of miles after the reset?
@camaromodschannel 4 күн бұрын
@ should be instant ,will work. or not..
@camaromodschannel 5 күн бұрын
Amazon Link www.amazon.com/dp/B0DGLGYJWG?...
@FrederickJackson-m1f 9 күн бұрын
I'm having problems with my coding p2097 and p2190 and p2188 p0122 and p0305 and p0455 p0435 and p125 engine Temp protection mode
@camaromodschannel 9 күн бұрын
Check your throttle body, and fuel injection. Thanks
@AA_Canon 11 күн бұрын
Mine is cracking and chipping too. Did you eventually buy a new piece to cover it up, or just rocking the chrome? Im just worried about possibly cutting into the seal portion or leaving it exposed to water.
@camaromodschannel 11 күн бұрын
No, I just left it chrome. Yes, just be careful when cutting. Thanks
@gudsoup7097 12 күн бұрын
I want to stop my led taillights from hyper flashing and I was wondering if there is a fuse I that I can replace to fix that issue.
@camaromodschannel 12 күн бұрын
Check all lights and make sure you don't have one burned out. And also you need all standard bulbs, or all LED bulbs. LED has less resistance and may confuse the electrical system. Check your front signal lights to make sure none are burned out. Thanks
@lvsqcsl 14 күн бұрын
I think 1960 in certain Mercury models, like this one, was about the last application of the 312 cu. in. "Y" block. I do know the 292 cu. in. "Y' block continued until 1964 in Ford F-series trucks. I am wanting to say that the 383 cu. in. was an MEL engine. GREAT VIDEO!
@camaromodschannel 14 күн бұрын
Thanks for watching.
@cjcoats9651 25 күн бұрын
I have a 2005 Cadillac sts4 V8 and I got the shift to park error hard part to find would a 2007 shift lever fit?
@camaromodschannel 24 күн бұрын
Best to change out the switches, would save you hundreds of dollars, and your used parts may go out in a years time. Yes I believe it in the years range. Should fit. Best to look up your parts on ebay and make sure it's the same looking parts. Thanks, anymore questions just let me know
@JoeJoe-pz9sw 25 күн бұрын
All you gotta do is look at his main page.. he says it’s for show only nothing is real.
@camaromodschannel 25 күн бұрын
Yep, thanks
@CamaroTime 28 күн бұрын
That's super cool!!
@camaromodschannel 28 күн бұрын
Thanks Pete.
@funnydogvoices514 29 күн бұрын
Where is the fuel pump rely
@camaromodschannel 29 күн бұрын
I never found it, but I hear its on the left kick panel on driver's side, by your brake, pull that kick panel off and look there. I have not confirmed this, so if you find this then let me know so I can help the next guy. Thanks
@camaromodschannel Ай бұрын
kzbin.info/www/bejne/e6ibXmCHgJdll9E
@Ladiezman127 Ай бұрын
Where’s the how to video??
@camaromodschannel Ай бұрын
kzbin.info/www/bejne/e6ibXmCHgJdll9E
@calivalley9056 Ай бұрын
Great video, had my starter go out, replaced it now no start no crank. Had been slow cranking for awhile, suspected bad ground or heat soak. Trying to figure out what could have happened, feels like the security system may have lock up , but tried a reset multiple times, no good. Im stuck, looks like I may have send in the dealer.
@camaromodschannel Ай бұрын
Check your connections on the starter again, your small wire that goes on the solenoid is that lose? Thanks
@calivalley9056 Ай бұрын
@ Figured it out, the ECM fuse was burnt. Swapped it out, fired right up.
@camaromodschannel Ай бұрын
@@calivalley9056 Awesome! Thanks for the report..
@christianfontaine2390 Ай бұрын
which body control module controls the brake light and turning signal?
@camaromodschannel Ай бұрын
There's only one body control module. Thanks
@johnmadden1605 Ай бұрын
Is there any coin pushers that do have high Stakes or coin pusher casinos that are legit have high stakes
@camaromodschannel Ай бұрын
None that I know of, a few in the 🇬🇧 UK, the may have a buy in of 5000.00 euros 💶 thanks
@johnmadden1605 Ай бұрын
Yeah you know what sir you do have a point if you was doing that for years he could have been a billionaire by now and if that money was real or whatever the winnings were real I wouldn't even have a KZbin channel I just be retiring and try to improve my life in other ways
@camaromodschannel Ай бұрын
Millions a week, he would be a multi billionaire.. yes, its just for KZbin views. Thanks
@johnmadden1605 Ай бұрын
100 million buy-in that's ridiculous if I had 100 million dollars I would retire straight up but I see this guy's content the one with the fake southern accent or maybe it's a real southern accent but I know he does million-dollar buy-ins I know he did a win of 350 million win one time which is kind of life-changing but if I won that amount of money I wouldn't be working or gambling anymore I'd be relaxing and enjoying life
@camaromodschannel Ай бұрын
Yes, coin pusher videos are just for entertainment purposes only. No Money made or lost. Thanks
@donnabrunner3125 Ай бұрын
This machine is in his basement
@camaromodschannel Ай бұрын
Mom's basement..😆 🤣 😂 😹
@draygangondeck6766 Ай бұрын
Where can I get some carpet man please respond and help me out
@camaromodschannel Ай бұрын
Automotive carpet you can get on ebay, pre-cut to fit your car. Thanks
@bradzyczynski660 Ай бұрын
I have the same car. My shifter isn't illuminating. Is it just a light bulb in there?
@camaromodschannel Ай бұрын
Yes. There is a couple lights on the shifter assembly. Could be burned out or not in place. Thanks
@bradzyczynski660 Ай бұрын
Would i have to pull everything out to get to the bulbs are just take out the center console and that wood grain trim piece?
@camaromodschannel Ай бұрын
@@bradzyczynski660 yes, trim and wood grain part.
@bradzyczynski660 Ай бұрын
Thank you so much!@@camaromodschannel
@Rev.nighthawk..pjred1984 Ай бұрын
I think none can do a buy in and max pay prize or value of a prize is $10 besides the coin pusher machines can be bought at $3000 or less license $500 I think 3 years and would be inspected seeing some on the y net are broken missing parts they won't be in a legit business and no buy ins the atf would close them down and bankrupt as well plus they most likely won't allow the filming for the y net
@camaromodschannel Ай бұрын
Yes, all coin pushers are fake, unless at a truck stop, with just a few bills, and small prizes. Thanks
@RaymondBriffa-w6e Ай бұрын
Anybody can tell where can I find location of the fuel pump relay on 1997 Camaro v8.
@camaromodschannel Ай бұрын
A fuel pump test point is,, under the hood. Passenger side, in the harness. Just above the PCM. Fuel pump relay is, remove Lower left kick panel, where your brake pedal is.thanks
@RyanRickles Ай бұрын
I pulled a micro switch from a 2005 Cadillac Sts that has a curved end is it possible to trim that end piece and use it in a 2008 Cadillac Sts? Thanks
@camaromodschannel Ай бұрын
Yes. You can. Just test it good before you put it all back together. Thanks
@RyanRickles Ай бұрын
I did and it works! Thanks so much for this video. Unfortunately I think I broke that little circular plastic piece to get the housing off and now it doesn’t want to shift out of park. Guess back to the junkyard I go
@RyanRickles Ай бұрын
It wasn’t that plastic part not allowing to shift out of park I didn’t properly connect the little metal celinoid shaft to plastic stop when I put it back together. People make sure you watch his entire video very throurough work he’s done you’ll learn a lot
@camaromodschannel Ай бұрын
Glad this video has helped you out and fix your car. Thanks
@camaromodschannel Ай бұрын
Thanks
@Starlynightlight Ай бұрын
Hi so I replaced the rear wiring harness (due to a crash) now the break lights, side markers and rear camera are not turning on except the license plate light, does the break lights have a fuse? Or is there something else I should be looking at? Thank you in advance
@camaromodschannel Ай бұрын
They are controlled by a switch in the BCM, body control module, so that is what I would look into the bcm. Thanks
@Starlynightlight Ай бұрын
Thank you ❤@@camaromodschannel
@christianfontaine2390 Ай бұрын
@@camaromodschannelwhich bcm though?
@onjisan Ай бұрын
I have a 2015 traverse. The car starts fine, but I have the service anti theft light. I did clear it once by disconnecting my battery, but it came back. Still the vehicle starts fine. Any ideas?
@camaromodschannel Ай бұрын
Turn the key in the on position without starting the engine, leave on up to 15 minutes or until the anti theft light goes out. Thanks
@onjisan Ай бұрын
@@camaromodschannel Thanks. I let it sit 29mins the other morning, but the light is still on. I'll try for longer next time.
@guybrick4490 Ай бұрын
Excellent video I’m ordering mine right now!! I like the way you took your time and was very descriptive. Thank you
@camaromodschannel Ай бұрын
Glad this helped you fix your golf cart, saving you time and money. Thanks
@guybrick4490 Ай бұрын
Hello again, I got my new stop sensor in the pedal and it is still doing the same thing as you described your cart was doing. My question is, did you end up putting the other sensors in yours?
@antonep4721 Ай бұрын
Were do the green orings go u show them but dont bother to show were they go
@camaromodschannel Ай бұрын
That was a whole system gaskets set, green one's for accumulator dryer, condenser, evaporator, all those parts use one o-ring per connector. I had already replaced those parts, this video was for compressor only. Thanks
@steveg2406 Ай бұрын
Most of these WiFi connect cameras I've used always send my cameras' feed to an unidentified foreign Internet location as well as allowing access to my devices. Hopefully this one doesn't.
@camaromodschannel Ай бұрын
The video is encrypted if that helps..thanks
@smootheggchowfun Ай бұрын
I just purchased
@camaromodschannel Ай бұрын
You will love these cameras. Thanks
@robertsmith9756 Ай бұрын
I think the VR is in the PCM on this one.
@camaromodschannel Ай бұрын
Yes, could be. Not really sure on this one. Thanks
@markwilliams7845 Ай бұрын
AV coin pusher isn't trying to get over on anyone, he made the buy ins so high anyone with 2 brain cells would no it's fake
@camaromodschannel Ай бұрын
Would (know)it's fake..not no.. 😆 🤣 😂 😹 yes he's never had a trillion dollar buy in, but I have.. 😆 🤣 😂 on , coin pusher R1
@fredysmith4790 2 ай бұрын
I can’t get to read lots of airbags on different vehicles not even show or it will say not available. Or ABS.
@camaromodschannel 2 ай бұрын
I don't think that one does airbags.. thanks
@ron-v2x 2 ай бұрын
Thank you for posting this up.
@camaromodschannel 2 ай бұрын
Thanks for watching
@MiamiTalk 2 ай бұрын
I’m running into a issue. Car has a big subwoofer from previous Owner, how in the world do I take this sub out?
@MiamiTalk 2 ай бұрын
Similar to yours in this video
@camaromodschannel 2 ай бұрын
Yes its a tight fit. Just take out the sub woofers first, to make it easier to move around. And just work with it and cut wires and pull it out. Thanks
@MiamiTalk 2 ай бұрын
@@camaromodschannel ahhh so maybe that’s it.. subs gotta come out and then the box?
@camaromodschannel 2 ай бұрын
@@MiamiTalk yes.. any time i had to take out the box i had to take out the subs first. yes a pain in the you know..where
@adriantellez9786 2 ай бұрын
Como puedo calibrar el cuerpo de aceleración de mi camaro 2010 v6??
@camaromodschannel 2 ай бұрын
you have to have a scanner that can do that. or take it to a shop. Thanks..
@isaacelliott6841 2 ай бұрын
Very helpful for my repair, thank you!
@camaromodschannel 2 ай бұрын
Awesome, great to hear. Thanks for watching.
@josephhrytzay997 2 ай бұрын
Never showed how to adjust air / fuel mixture!
@camaromodschannel 2 ай бұрын
Should be other videos on that. It ran good as is..
@Cannones 2 ай бұрын
What are some extra tips you have on getting the valve out? This thing is really battling with me
@camaromodschannel 2 ай бұрын
Wd40, or some kind of oil. Thanks
@Cannones 2 ай бұрын
How long should let the wd40 stay on it for before trying to pull again @@camaromodschannel
@camaromodschannel 2 ай бұрын
About an hour. Thanks
@Cannones 2 ай бұрын
@@camaromodschannel you're 100% certain that the 2013s let you remove the valve? Iv tried so many times and even spray wd40 on it and no results. It's almost getting to the point where I'm damaging the actual value because I keep clipping at it with pliers.
@camaromodschannel 2 ай бұрын
@@Cannones mine was a 2012 don't know if they changed it or not..wow never heard of one so hard to come out..
@melissaavila9253 2 ай бұрын
Is this in the rear tires?
@camaromodschannel 2 ай бұрын
No. Front only. Thanks
@marcusking29 2 ай бұрын
If a sloth was a person
@camaromodschannel 2 ай бұрын
And I'd be good at it!! 😆 🤣 😂 😹 😆 🤣 😂 😹 😆 🤣 😂 😹 😆 🤣 😂 😹 😆 🤣 😂 😹 😆 🤣 😂 😹 😆 🤣 😂 😹 😆 🤣 😂 😹 😆 🤣 😂 😹 😆 🤣
@xnvyo.o1347 2 ай бұрын
What if i wanna install a wing, how do i cover with the holes?
@camaromodschannel 2 ай бұрын
Small bolt, rubber washers, on top and bottom, then nut. Thanks
@7need.A.trophy 2 ай бұрын
what fuse controls the tracking on the car?
@camaromodschannel 2 ай бұрын
40 and 43 under the hood. Thanks
@7need.A.trophy 2 ай бұрын
@@camaromodschannel okay appreciate it just subscribed
@7need.A.trophy 2 ай бұрын
@@camaromodschannel and camaros and also corvettes usually have multiple fuse boxes correct?
@camaromodschannel 2 ай бұрын
Yes. Thanks.
@camaromodschannel 2 ай бұрын
Your welcome, thanks for sub..
@7need.A.trophy 2 ай бұрын
what fues controls the horn relay?
@camaromodschannel 2 ай бұрын
Terminal 30, thanks
@youtubeFirstGrowTips 2 ай бұрын
Your video quality is very nice to see! When is the new video coming?
@camaromodschannel 2 ай бұрын
I don't have a product Review right now, and it may be another few weeks before I release another on solar panels ground mount. Thanks
@youtubeFirstGrowTips 2 ай бұрын
@@camaromodschannel Your video is very good but why so few views
@youtubeFirstGrowTips 2 ай бұрын
Hello, how are you Hello, I am a regular viewer of your KZbin channel! I like your videos, when will I see your next video? I can find out !!
@camaromodschannel 2 ай бұрын
In a few weeks, thanks
@user-ym9oc7jh6m 2 ай бұрын
Jesus fucking Christ read faster omfg