do you still have that tool available

Don’t try to pull them out, instead push the bit a little bit center and up using your thumb.

Out of interest, why did you give up the airgun market ?

Hi Nice to see you still around and doing ok You tuned my R10 it was in the last batch you did before shutting up shop. Ive still got it has had the normal seal changes and it's still going strong . All the best .

I have the GVS Shadow, very happy with it, I use it at three storey gutters👍

Looks like a good bit of kit..

Gutters are a nightmare to clean, but this machine you have seems to do a great job of cleaning them. Well done and any chance you could pop round and do mine? LOL Take care and stay safe, Joe

I would call that a 'success' Darrin, even doing it by hand it's a tricky undertaking .. 👍 The rain should clear out the remaining little bits .. 😉..😅 atvb t ..

I have BSA R10SE high Power.I want to lower the power to sub 12ftlbs can they be done without changing the regulator

That end does not come off that easy so this BS. That cap has been off previously. I've heated it and even hit the Stanley blade with a hammer to drive it in. Not a bloody chance. Instead of making this easy to video why don't you show the difficulties encountered as in REAL life.

The rule 'any available commercial pellet' changed quite a while ago. Judges ruled your gun can only be tested using the pellets the user had with them at the time. It was ruled absolutely impractical to stick to the law as laid down. Commonsense actually prevailed.

You're doing a review aren't you? If you're interested in seeing what happens when you drop it, then drop it and let us see.😅

Thank you for your help 🙏 with air gun videos, your videos help so many people and helped me much, good luck with your new direction wish you all the best

Neff require a minimum 40mm space on either side of the plate. Is this just for pan handle space? I ask as our units have an extra thick section for installing a hob but it’s the same width as the proposed new Neff induction hob. There is space at either side but it’s lower than the thick section. I emailed Neff but got no reply.

Can you do a bsa r12 video

Darrin, is that proper paint, or the water based shit?

Maybe send it back. It doesn't looks like it's that hard to get the bits out in the other videos I've seen. (Update just got mine and it's so easy to take them in and out. If you're pulling the bits straight up. Not out and up. And even if you don't put them all the way in. The magnet will close it anyway.)

Good stuff Darrin. Could you sneak the odd airgun episode in, if you ever get the time? Thanks Pete..

It’s a shame you’re not doing the Rifle videos anymore I learnt such a lot from them but love your other work to maybe one day you’ll start doing the Rifle videos 👍👍

It’s a shame you’re not doing the Rifle videos anymore as they was brilliant and I learnt a lot from them and maybe one day you’ll bring them back but love your other work too 👍

Looks like Wiha got the hang of charging a premium price, just not the making of a premium tool.

Very helpful video, thank you. I’ll be doing this job later today

Sadly , the pocket max isn’t out in North America yet ! Do want !

I got one 2 months ago. It gets used daily as the "pocket driver. Pull the bits out from the thick end! It's much easier. Bits are not Pozi, BUt Philips! Also, annoyingly, all the other,Wiha bits are too long to fit in handle, a bit annoying BUT it is well,worth it

From bsa r10 regulator to mud flap installations. What do you do for a living now

Nice clean job! Always interesting to see these DIY projects… Thanks for sharing it with us!

Good stuff Darrin. You spotted 3 more meteors than I did in Essex. It was pleasant sitting in the garden gazing at the sky, and slurping a bottle of wine though..

My Electrical teacher in college made himself one of those with conduit for the handle and axle and a cylinder from a former cooking oil vat from the canteen. Filled it full of cement and bobs your aunty!

I only see one idiot 🤷‍♂️🤣

A good job well done. But for anyone in the UK (and likely Europe) at the moment it is not, IMO, a good idea. If on a gas supply there will be no energy outages this winter, but leccy could be restricted at times. Any gas outage would require all affected properties to be checked, on re-connection, to avoid any disasters, so a ‘gas black-out’ is very unlikely. Apart from the above, thermal energy (gas) is far, far less expensive than electricity. Both are spiralling in cost at the moment, but even if gas usage on the hob was only 50% efficient (it is much better than that, I believe) it will still be less than half the cost of doing the same job with an induction hob (that also has efficiency issues over even a halogen powered hob?). At the present time gas costs less than a quarter of the same amount of electricity during the day-time.

Thanks for the truly honest assessment, I had watched delboys garage big this stuff up but thought he was paid to say how good the stuff was, tbh the blood made my mind up!!

Love it. That work surface should have an air rifle on it, and one of those screwdrivers should have a 'Pokey' thing. 😊

Miss you work on the airguns 👍

Good luck with your new venture. I know you have closed your air gun store. Just wondering if you had a spare air arms s200 reservoir removal nut that you could sell?

Just wanted to say thank you for the air gun videos, they were an immense help for me when I had issues with my R10 - glad to see you're okay and look forward to some good old sparky content :)

Just a big thank you for your BSA videos.

Hope it all goes well Darrin. Good to see you back.!

ДОБРОГО РАНКУ! ТАК ДЕРЖАТИ

Nice one, good to see you back. Appreciate all your past postings, I've learnt a lot from them thank you

Great to see you back again on KZbin! Your info on airgun tuning was so valuable to me. Thanks for sharing all this knowledge to the rest of us... Wishing you all the best with your electrical business.

Good stuff Darrin, but miss you fixing PCP airguns.

Wish you had time for both! Your videos helped me tremendously thank you from the USA 🇺🇸

Good to see you are making out ok Darrin, looking forward to see just what you are tinkering about with now 😉 .. 😂 .. 👍 get posting real soon. atvb t ..

Best of luck Darrin..

Hi mate ..miss your videos and your voice..still watch the old videos with admiration.. good luck with everything and look forward to seeing and hearing from you soon...

Another Worcester lad says good luck, enjoy your videos.

Welcome back

Great to see you back online. Your airgun videos have helped so many people including me with your amazing BSA Ultra strip and tune vids

Great 👍🏼. Your contents are very useful. Best wishes.

nice to hear your alive an well wb