There is no way to get a consistant density. Your wing will be unbalanced.
@Totallynottrusted5 ай бұрын
Idk why the thumbnail looks so delicious 😂
@charlieryan86249 ай бұрын
Stick a gyro in there with just AS3X
@ademcelik6659 Жыл бұрын
Almanya’da sıtroba ile köpük nasıl yabılır
@jeffswope1511 Жыл бұрын
Like your process
@ahmadfouadassaf6856 Жыл бұрын
gut
@godorzsolt9451 Жыл бұрын
I tried and tested like this for 25 years ago. After a week, the finished wing twisted.
@Pro100Zigmun2 жыл бұрын
Когда работаешь на стройке и пены хоть жопой жуй.
@terminsane2 жыл бұрын
what is the weight consistency like?
@mfs54932 жыл бұрын
Why break up the excess foam? It can be carved into nose cones etc.
@eclipsetoys65512 жыл бұрын
Cool model great flight but geez expandable foam ugggghhhhhhhh I would pick nearly anything but that....feaking nice job on the 2mm veiws
@tombouie2 жыл бұрын
Well-Done
@SanthoshKumar-mr5ss2 жыл бұрын
Did u use polyurethane foam?
@moonscrafts89872 жыл бұрын
The best ❤️
@juliocesarmonsalvo74423 жыл бұрын
Excellent techniques
@wk7133 жыл бұрын
It's polyurethane ?
@DarcyWhyte3 жыл бұрын
is it normal to want to eat it?
@makewhatyoulike1193 жыл бұрын
very cool but I'm sorry, I don't understand what propels it forward. Is there a propeller not shown?
@diegoherrera22343 жыл бұрын
feicitaciones desde Chile yo quiero hacer uno grande
@rcbuildmaster61924 жыл бұрын
What's the weight of this rig
@ahmedrc89864 жыл бұрын
kzbin.info/door/MJL01LKzRqRZ6-dz8lnPaw
@vigicon4 жыл бұрын
10 times wastage of the material
@blainsmith30974 жыл бұрын
super cool bro !
@stolaircraftsuyanto97284 жыл бұрын
Hallo.mahan_bahan what should be prepared. Thank you
@evgeniynikolaevich61454 жыл бұрын
Это очень плохое решение для летающей модели.
@timexironman100m4 жыл бұрын
A lot of work goes into making the molds.. making the wings looks easy part....
@bdrw80324 жыл бұрын
You have CORRECTED me , Sir! I tried this when Expanding foam first came out...and failed so bad I thought it was a "dumb" idea, LoL!
@soufianeelouafi45094 жыл бұрын
ما اسم هذه المادة؟
@burnerjack015 жыл бұрын
Couple of possible improvements: 1) Put down cling wrap on table to aid cleanup. 2) Maybe embed servos and electronics in wing before foaming or using cling wrapped blocks to make exact voids in foam for electronics. All that being said, great process, great results. Well done.
@jimmytiler55225 жыл бұрын
Wit till you see my easy peasy way to get the perfect foam wing.
@matrox5 жыл бұрын
4:15 So..he baked some bread??
@tastelikechinahadababyandn99284 жыл бұрын
or turtles
@JB-pt6kd5 жыл бұрын
I used expanding polyurethane foam from a can to prevent strong winds lifting corrugated steel sheet on my workshop roof . (This had been laid over a flat felt roof which had begun to feel its age and started to leak). A one-second squirt into each of the raised metal corrugations. Worked fine, the wind did not lift the panels any more, but the foam just kept on expanding at a very slow rate for about a year until it was stable. Concerned that a wing section may change unless kept in a jig for a long time to stabilise.
@factdesignbr5 жыл бұрын
Where do u live brother? Nice hill
@ahmadattar73355 жыл бұрын
🌿🌿🌿
@farmers26305 жыл бұрын
Very cool.
@ConsertandoTudo5 жыл бұрын
the wing resistance is greater than Extruded polystyrene (XPS) ?
@ExstrimHouse5 жыл бұрын
идиот,такое крыло струной можно нарезать за 10 минут
@jimmytiler55225 жыл бұрын
That material your using should mean your use of foam is mute.
@slavas92005 жыл бұрын
Unusual way, but not the most simple. I would not try.
@guntherultraboltnovacrunch52485 жыл бұрын
I hate when a video starts off with a a still. I can't tell if I hit play or not.
@incubusfan42115 жыл бұрын
I have used this method for creating "nerf" footballs. Great job. My wallet thanks you.
@jelleterpstra655 жыл бұрын
Great master
@alighane55465 жыл бұрын
trimming is difficult due to weight. tail would,ve be good
@jeffreybail3535 жыл бұрын
the earth is spinning 1000 mph no need to fly just hover and wait for the spin
@adoreslaurel5 жыл бұрын
What is "expanding glue"?
@ZacLowing5 жыл бұрын
3:58 poke poke poke touch touch doink poke pokypoke pooker poke poke poke POKE POKE tap tap tappy tap poke
@davidowencoxon5 жыл бұрын
Nice, but there's a lot of waste.
@hakapik6835 жыл бұрын
Stupid idea. White foam block, make a foam cutter from nichrome wire, VERY easy to build. 2 plywood templates the shape of the wing root and tip glued to foam block, cut the wing core and then use 3M spray adhesive to glue outer skin to foam core that you made. Very easy to make as many wings as you want or need in very little time with no mess or screwing around like what you did.
@ThePostal675 жыл бұрын
Just a thought, were does the waste go.... Can you eat it so it not wasted?