Bought one, tried to make it work for an hour, dumped it in the trash where it belongs. All that is left are bad memories and a hole in my work bench.

To each their own, but I removed the "lip stop" with the 2 small screws. I line up the cutting edges to be vertical and parallel to the wheel's side, by eye. It's one less "figity" adjustment I need to make. The bit rolls easily in the "V" groove to line it up. I've sharpened hundreds of bits this way on my old Craftsman and a newer identical version off Amazon, my spare! I do a lot of drilling in metal, even stainless steel, are real bugger to drill. I just finished drilling two 1" diameter holes in 1/4" mild steel plate. I started with a 1/4" pilot, then a 1/2", next a 3/4" and finally the 1" diameter.

Those titanium nitride coated bits are not intended to be sharpened. The coating is what keeps the bit hard.

I have a chrome 12 volt model on my '46 Dodge flatbed truck. People love it, (especially children) at car shows.

Great video. I watched this before setting up my sharpener and was very pleased with the results. Thank you!

What are you using for the gasket material? I hve about a dozen of these horns of different manufacture that I will be refurbishing.

Did you remove the coolant diverters from the block cuz they’re not in place. There’s two rubber strips per side that push into the water jacket to force the coolant to circulate around the cylinders and not just directly from the inlet to outlet. If those aren’t there it’s guaranteed to have overheated. You could pull the intake port covers off to see the rings and piston skirts from the side also.

Where is the water in-flow source? If you don't find it and fix it, it will just get water logged, heavy, and rot out again.....

Excellent!

Looking good!

What you need to finish the dashboard restoration on your boat is a dashboard hula dancer figure from the 60’s 💃

I’m amazed at how much you have done already!

Very satisfying

👏👏👏

Congratulations 🎉 looks like a great project. Hope you have fun.

Need a wheel designed to be used on sides

That's not how you sharpen a drill. That's completely the wrong geometry. 🤦‍♂️

In your recomendations of it, might I recomend posting a link to the tool?

Thank you for the great tutorial, great teacher.

❤Дякую!!!

The side of that grinding wheel is not to be used for grinding - only the face is to be used. It creates a very unsafe condition if you start removing material from the side of the wheel.

Maybe you can tell me too, please, how you adjust the 2 screws in front and with the piece of thin sheet from them lifted up . I wanted to send you a picture, but I don't know how

Did this ever have an update?

Nice video! What background music did you use?

great job !

So, sharpen drill bit, then dull it by using it as a pointer,

👍

Looks amazing!

thanks . same as craftsman 6677 or general 825 . after watching some vids , and some trial and error , i'm well pleased with mine . i advise to install a locknut (the thread size on my general 825 is 1/4 coarse) on end of threaded rod , to avoid losing the lower thumb wheel . the indicator can , in some instances , hold the bit from laying (lying?) in the trough correctly . adjust it to just barely touch the bit , and tighten the bit clamp securely .

Excellent video, you really hurt your fingers a bunch hope they healed up ok.

This is unrelated, but, your channel name is perfect

"Sealey SMS01, General 825, Picador no 9 Drill bit sharpening jig. WHAT YOU MUST KNOW!"

@i'll be in the garage, where could i found one similar? What are the specifications of the one you bought?

No need relay to install? For 12 volts?

got one of these ,thanks for showing me how to use it ,very helpfull

Just saw this. So great!

hi do you have some other videos on the cement board and how big of a wheel you can do

Ooh! It came out beautiful! The flame bulb really adds a nice effect to the light 🙂

The black pointer is a position indicator to get both edges in the same place

Give me price

Sorry, more bad advice from someone who does not know or have experience with this tool. Thumbs down.

Excellent explanation. Would you mind tell me which are the dimensions of the base sharpening drill? Greats from Honduras!!!

Excelente, me encantó. la restauración y como suena.desde Colonia Uruguay

It seems like this product works well but I have two concerns. First, grinding on the side of the grinding wheel seems like a safety issue unless the wheel is made for it, secondly, after some time the side of the wheel would develop a groove or a concave wear pattern and I'm not sure how that would change the sharpening pattern. How would you then true up the side of the grinding wheel.... ?

that is so cool i wanna put one of these on my bike

Con más cuidado que le arruinaste el costado 😢

Those drum brakes have brake shoes, not calipers. Calipers are on disk brakes.

I hope you folks attend the 2023 Old Car Festival and make some new videos, even if you just document cars in motion. You certainly have the knack to supply quality videos.

really nice job