Chris N' Cars

Пікірлер

@AmusedSketchpad-mh1qz 20 сағат бұрын

The others touched on it already but the push rod is hardened , and brittle metal breaks easy. Go gentle on that longer bolt. DONT CRANK IT!

@JoeSmith-pd6ck 4 күн бұрын

So Chris, this was posted a while ago, but indeed seems a nice, concise addressing of the subject. I do have a question though (if you know), I am working on my '57 Chevy Bel Air and it seems I do not have the hole... OR those 2 holes (on the 283 at least) are used for the front engine mounts. I'm guessing that perhaps the block didn't change when side engine mounts were done, but not sure. My real question though, if you know, is if the upper front engine bolt is this same bolt you are showing.... seems ill-advised to remove and engine mount bolt (when the engine is mounted in the car)... but I'm curious if anyone has done this. Near as I can tell (very crowed in there when engine installed) there are 2 bolts for the mount, so removing 1 might be OK.... just looking for feedback.

@ChrisNCars 4 күн бұрын

@@JoeSmith-pd6ck as long as you get the engine mount bolts back in and torqued properly I don’t see a problem. You got to take the engine out to work on it sometimes, removing one bolt won’t throw it off alignment or anything.

@JoeSmith-pd6ck 3 күн бұрын

@@ChrisNCars Thanks Chris for the quick reply. My question though was if these engine mount bolts are the same you are indicating as holding the fuel pump rod/plunger.... seems it could be, but not sure

@ChrisNCars 3 күн бұрын

@ oh, yeah I think so but why not run to the hardware store and just grab a long bolt? I say the thread pattern.

@LField-uf7qf 4 күн бұрын

Hopefully still see this cuz video old I’m confused I’ve got 18gks450 and I’ve done everything you said and all made sense however light is on so when I researched it everything says the rotor completes the circuit not cut it and tying wires together is completing circuit can you please advise. Sensor’s on back order

@ChrisNCars 4 күн бұрын

Hmm I’m not sure on that model, sorry this didn’t work for you. You can try that car side of plug or check you do not need to reset a service interval

@LField-uf7qf 16 сағат бұрын

Thank you for taking the time to respond back to me even though the post is old. So even though every a i you ask or Quora or just google says your method is wrong. States ur method creates a circuit and that causes the light to come on I had faith in you. I rechecked my work and had not noticed that the wires had a cover on them that had to be stripped. They are so small and so clear I couldn’t tell. So I stripped them and guess what happened. Yup no more light. I really appreciate your help. Also goes to you that no matter what people want to think a live human being will always be better than A I or google over all. Thanks my friend and I hope the anoucement tomorrow sits easy with you 😁

@ChrisNCars 15 сағат бұрын

@@LField-uf7qf Nice! Yeah the stripping of wires can get you some times, ha! Glad it worked out in the end.

@jonhdoe9623 4 күн бұрын

It did help. Thank you for the video.

@timothygarza3699 6 күн бұрын

Thank you for making this video. I’m more convinced to buy one now. How did the fans hold up? Did they ever go out? Again thank you so much.

@ChrisNCars 5 күн бұрын

@@timothygarza3699 I sold the truck a few months ago but they worked great up till then

@marcorodriguez4436 7 күн бұрын

Nice buddy

@basiliogonzales4099 8 күн бұрын

Let me know please thanks

@basiliogonzales4099 8 күн бұрын

After changing the brake pads and rotors, do you need to install the computer in the car or is it normal like any other car?

@ChrisNCars 8 күн бұрын

@@basiliogonzales4099 no computer. You can go into the vehicle service settings and reset the brake pad change notifications.

@kat0197 8 күн бұрын

No no no. I don't have a xenon light just H4 Bulb like yours and I got Sensors Level for them. One on front and one on back.

@marco-fw7nx 12 күн бұрын

Salut combien rentre t il huile exactement merci

@jeffbrock4705 12 күн бұрын

Thanks for this. I would've piddled around with it for an hour on my 2017 Q7 before figuring it out (yes, the 2016-2019s have the same setup). Had to replace it because the plastic main support with the vanity mirror wire, which is on the other side of the visor, broke in half, as most of them do. As it turns out, my T20 bit on the end of a magnetic driver couldn't get to the screw because of the diameter of the hole, so I ended up breaking the bracket to get to it. I replaced all the Terrible Ts with Phillips head. The biggest flaw with Q7 twin visors is that Audi designed a "trough" into the plastic main support that has the vanity wire mirror. This trough runs completely from side to side and is about ½ the thickness of the already-thin plastic. That's where those plastic supports always break, which means that Audi designed them so that we would have to spend $650+ replacing them. Planned obsolescence. Dirty. In addition, once that breaks, it usually breaks the plastic clip-in section at the back of the support anchored to the roof, which is something you can't easily remove. So you're left with having to secure the entire weight of the twin visor with one screw unless you want to pay an additional $650+.

@nevamind68t23 16 күн бұрын

Thanks 👍🏾

@Miketrees-j5g 17 күн бұрын

had to thumbs up the vid... mario kart in video awesome... best game ever was super nintendo mario kart.....yes i know his was n64 kart i believe...

@tekka8771 21 күн бұрын

I unfortunately broke the purple part from the antenna connector. It still seems to connect fine and I think it’s a separate piece so hopefully I could get a replacement if needed.

@johnparker1477 22 күн бұрын

DONT HAMMER ON YOUR SOCKET WITH A STEEL HAMMER! Otherwise good video for DIYers trying to work with what they have. Thanks.😊

@DismalWoodworking 22 күн бұрын

Love the video. Getting ready to do the same on my Silverado.

@Obscure_Climbing_and_Fitness 23 күн бұрын

Amazon claims that this piece "Genuine Audi Accessories 4L0055305U 7-Pin Towing Connector" does not fit a 2015 Audi Q7. This is the same part and the same vehicle as in this video though, correct? I've tried several off brand adapters and the brackets do not line up properly, so securing it into the vehicle is a hassle, requiring attaching a new bracket to secure the Hopkins brand connector. I'd rather pay triple the price for an Audi specific one, I just want to double check the part number and vehicle prior to purchase.

@ChrisNCars 23 күн бұрын

@@Obscure_Climbing_and_Fitness 4L0055305U is what I used on my wife’s 2015 in the video, it should work.

@eddychance4860 Ай бұрын

Your video was very helpful as I installed one in my 72 C-10 yesterday. Having your wiring diagram was very helpful. Thanks

@ChrisNCars Ай бұрын

@@eddychance4860 thanks for the comment glad it helped.

@bertjesklotepino Ай бұрын

Chris, i have a mini from 2009, and the heater inside the car does not heat up. The fan also keeps running after the car has been switched off, plus it starts running when the car is cold and just on ignition. I replaced the thermostat, and now the heater inside the car works fine again. But now the fan does not start up anymore. I have seen a video where the symptoms i just described show the fan has also gone bad. What do you think? How to test if the fan indeed has gone bad? May it also be possible that by switching around 2 of the connectors to the sensors on the thermostat (the 2 connectors that you can actually switch around), this prevents the fan from starting? Any ideas would be much appreciated.

@bertjesklotepino Ай бұрын

btw headlights going up and down following the road..... as a Trucker in the Netherlands i am not so fond of this new tech. Because you sometimes think the other person is driving with the high beam on, but they aren't. And so, to warn them about it i often signal them, but it means i am signaling people who did not have their high beam on. Still, their headlights blind me from time to time. On a high way it is not the biggest problem. But a country road where we pass next to eachother, it can be very irritating. Plus blinding. So: To be honest: NOT the best idea.

@benkneisley3001 Ай бұрын

Simple easy video, thanks. I also like to wipe out the filter housing with a small microfiber that has been sprayed with Isopropyl Alcohol before reinserting the new filter.

@ChrisNCars Ай бұрын

@@benkneisley3001 solid add, thanks for sharing.

@sarahfranssen Ай бұрын

Great video. All these awesome features are thanks to BMW. Most are standard on BMW’s. Also worth noting the there is a cigarette plug in charger located in the trunk (good if you’re camping). Not only does the seats move up and down but so does the steering wheel. Also comes with umbrella clips in the trunk.

@peacepoet1947 Ай бұрын

Having a rough time getting the pin to move back to install my new fuel pump on my 72 Chevy El Camino.

@ChrisNCars Ай бұрын

@@peacepoet1947 the pin jammed?

@peacepoet1947 Ай бұрын

@ChrisNCars I'm aware of the issue, but I'm not sure how to get it unstuck. I learned that you can remove one of the fuel pump bolts, and there is another on the front of the engine by the fuel pump. You remove that shot bolt and replace it with the longer bolt to hold the pin in place before removing the fuel pump. It's easy taking things apart, but sometimes not so easy to put back together!

@ChrisNCars Ай бұрын

@ the bolt that holds the rod I could see getting stuck but the rod itself? You can try taking the timing chain cover off and getting it from the top or drilling and taping threads into the bottom of the rod? Timing chain you have to drop the oil pan a bit and it’s a pain to reseal without pulling the engine.

@ChazEdgar-ik9fr Ай бұрын

Ty for keeping it common sense simple. I was truly amazed at other videos that were trying to explain same exact thing, but they were all over the place and difficult to even watch let alone learn from. So again ty for your help and the intelligent way in which you do. I'm a new subscriber, looking forward to future content and maybe making some of my own in the best future. Totally different category of content for me,but yeah. Lol hagd

@ChrisNCars Ай бұрын

Thanks! Try to make videos that are educational and entertaining to watch, glad you enjoyed and thanks for the sub!

@reckless_livin1852 Ай бұрын

Way to go I’ve seen so many people forget to hold up the caliper and break the lines😂

@ChrisNCars Ай бұрын

@@reckless_livin1852 haha!! You know how we do.

@Roomba321 Ай бұрын

This video made me realize I was missing the push rod bolt entirely on my 305 lol It was just an open hole

@danielver4484 Ай бұрын

Nice fix, thanks!

@brandongonline1432 2 ай бұрын

Good Video

@eddychance4860 2 ай бұрын

Great video I like that you got right into what you were doing. So many people talk for a hour before they tell you what they are doing. I have a 72 C-10 that I'm going to install one of the into thanks for sharing the video.

@ChrisNCars 2 ай бұрын

@@eddychance4860 happy it helped! Worked great till I sold the truck a couple of weeks ago

@johnboy4161 2 ай бұрын

Just be aware this is not for all small block Chevys. I have a GM Performance crate 350 and that hole is not drilled into the fuel pump rod passage. I have t use the old shim trick.

@1968Beetle 2 ай бұрын

Going out in the garage now to fix it! I've been putting it off but almost have everything else fixed on this old 68 bug I've had for three years now. This looks easy peasy. I'm getting ready to change the swing axle boots using a floor jack, jack stands, and a spring plate torsion bar tool. Never have before. Hairy scary. I don't want to get squashed like a bug by a bug. All the other vidz are either on a lift or with the engine out. I heard jack one side, set a jack stand, then jack the hub level and go under the car to replace the boot. No way. That's probably why there are no videos showing it either. Getting in there will be tough but I have to do it. If I had a camera I'd make a video. Excellent video on the speedometer. Just what I needed to start my morning (retired 65 yr old wrench turner).

@bikramjitubhi4141 2 ай бұрын

Did you disconnect the battery at any point during the process?

@ChrisNCars 2 ай бұрын

@@bikramjitubhi4141 usually always do

@gilbertsepeda257 2 ай бұрын

Awesome! many blessings

@brendafolk9907 2 ай бұрын

Simple, quick and without buying a kit! Loved it!

@richardhusman3650 2 ай бұрын

Thank you

@Shawn-s8t 2 ай бұрын

You Might As well Show me ALL of the REAL GLOBAL TOP Secret SUPERHERO and SUPERVILLAIN SHIT while we're here in NYC ASAP Infinity Symbol. C.I.A. and All TOP Secret Underworld and Command SHIPS Supremacy whatever... I wanna see ALL OUT C.I.A. WAR in NYC all the Superman SUPERVILLAIN SUPREME MILITARY COMMANDER NYC. Police MP Police Fire Department Ambulance EMT all STAR WARS Supremacy Commanders ETC. ALL OUT NYC Civil WAHR = The Cat's Already FAR Out of the BAG

@Shawn-s8t 2 ай бұрын

@tobe4141 2 ай бұрын

Didn't know about the bolt, but I jus put grease on the rod

@UncleFjester 2 ай бұрын

*$25 air tag for recovery, $3 Killswitch for prevention*

@stevethebaldyone 2 ай бұрын

Great video thank you for doing it and sharing it on you tube it’s very useful to me as mine is lose

@ChrisNCars 2 ай бұрын

Happy it helped

@MAtangan0418 2 ай бұрын

Do you have to do this to all 4 sensors or just 1?

@ChrisNCars 2 ай бұрын

@@MAtangan0418 All 4

@cliffolivent7901 2 ай бұрын

Love the flip flops😂

@ChrisNCars 2 ай бұрын

@@cliffolivent7901 you know!

@johnchampagne2247 2 ай бұрын

is it possible to change the rotor without removing the caliper? It seems like there is plenty of room after removing the brake pads. I am going to change my brakes this weekend and just trying to minimize the amount of work. Thank you for the video!

@ChrisNCars 2 ай бұрын

@@johnchampagne2247 unfortunately no not enough room