Hello sir we want pc400 software how to get it..

Simple and correct explanation for understanding float meter method. Thank you, sir

Simply perfect...

Hi! I plan on doing this some time next year with an ourtdoor social group and would love to get ahold of the documents you had posted. The website is no longer up. Thanks!

Sir thank you for the video. I want ask about how to using the average of velocity in this equipment?

So I'd like to ask. If a person put bolders let's say roughly 10 feet on each side of that exact spot how would it affect this whole equation.

This is right time video for me thank u so much

Why 0.85 for velocity adjustment

Battery life is good(this one ran roughly a decade) but when it fails sending the thing in for service to replace the battery is over 1/3 of the cost of a new one. Currently they have a supply shortage and service is impossible. So we replaced the battery instead. The split location is the seam line around head. This one has a short interior flange that sticks down from display side inside the lower half with a bead of sealant around the bottom edge. Because I went looking for tabs to unlatch and there were none I cut part of the flange off while getting this one apart. There are no tabs and no alignment notches in this one so 2 potential strategies to try getting it apart. A really strong twisting motion might separate the cases by breaking the sealant. Alternately I would try gently flexing the plastic of the display side in with a pair of slip pliers to break the sealant in localized locations. Repeat till worked far enough around to get the sealant loose. The halves separate and 4 screws hold the display to the case house. Be sure the meter is face down while you do this as there are 4 tiny metal pins that extend exterior buttons to the interior buttons that are incredibly easy to lose. If face down they will stay in their plastic holders. The battery in this one was a solder in that any good electronics person should be able to change with a battery cost of a few bucks(vs over $450 to service it)(freight will cost you far more than the battery) The battery in this one was CR-2354/HFN. Since we needed it fast we subbed with a CR2450 because they are commonly available here and only 10 mA lower max draw. 560 mA max draw orginal vs 550 mA max draw for the 2450. We fudged a holder together with epoxy and edges of a windshield wiper blade that will work for now.

Thanks

Does any float go downstream at the same speed for example like a rubber duck or a peice of paper would? does mass matter

Amazing video. Thank you

Thanks from Brazil

Nice explanation

Thanks for the simple and understandable explanation and application of discharge measurement

what if it is a waterfalls?

This is good as it measures an actual flow - thanks

We have to of the EZ-Flume (Nu-way) flumes in our ditches of the 7 CFS size for ditches with 3 CFS and 2 CFS water rights that are working well. We have another location that is a 1/2 CFS water right - do you have any suggestions? We have switched from the ditch approach to pumping with a collection of ram pumps at the above location. Pump meters are expensive and probably won't work with our low pressure low volume pumps anyway. The only thing I've been able to dream up is to first measure the output from the stream with a flume and then drop the water into the drive pipes for the pumps. There are a lot of ditch water rights in Colorado less than 1 CFS and measuring devices are being required on all ditches - any suggestions?

Thanks very helpful.

Thankyou very much .. most in depth I've found so far

Perfect demonstration for this topic because, it is easy to understand perfectly and simply....

Good job

Thanks a lot for doing this video🌟 I have a small Doubt for the 0.85 roughness value. how will you actually calculate it on what basis

Thanks for saving our bums for geography class with your clear explanation and steps. 10/10

Error writing one or more files

sir i really thankful for such a good explanation so for

How about for open channel sir, Is there any method or approach to measure flow? The open channel is trapezoidal with possible sedimentation. Thank you and God Bless.

0.85 sir

hello a question, I would like to know how is the right of the windlass elice, against the current or in favor of the current?

hello a question, I would like to know how is elice's right?

Great video, but you should always stand downstream of the depth stick for accurate measurements.

Is surface speed same as underneath? Obviously not. But is it neglectable?

I loved this. thank you for the clear demonstration

Thanks for sharing and please upload another video to calibrate it...

Is there any effect of depth to measure velocity of water by global water flow?

www.inmtn.com - we have many options for monitoring flow in rivers, streams, canals and pipes.

www.inmtn.com - Please visit our website to learn more about how we can help you select the best monitoring system for your project needs.

www.inmtn.com - we have many options for monitoring flow in rivers, streams, canals and pipes.

www.inmtn.com - we have many options for monitoring flow in rivers, streams, canals and pipes.

Go to www.inmtn.com/water/water-flow/flow-sensors/ We can help you to create a complete open channel water monitoring system.

Thanks for your videos. G

You can also use the Flow Probe as seen in this video. kzbin.info/www/bejne/oIqce6ubZbNooK8

the lecture is interesting and colorful.after doing this and the like we can find stream discharge.but what the problem is how to find the daily flow having event based flow like the following measurement. 4/12/2017 at 6:00 we have 0.2m3/s ,4/12/2017 at 18:00 we have 0.15m3/s, 4/13/2017 at 5:30 we have 0.3m3/s,4/13/2017 at 15:00 we have 0.25m3/s ,4/13/2017 at 19:00 we have 0.5m3/s etc .use spread sheet. "[email protected]" thank you for doing this.