whats a thermester?

I just had a 60 gallon indirect installed, do I need to flush it 2 twice a year?

you forgot to vent the filter at the end

Are these made in USA now?

It would be nice to see a quick walk through of the boiler configuration webpage.

Ngl did that with basically every measurement i took, you will not believe how much that helps especially when problems arise later

Thank you!

Pros?

How about a system you can do side exit so you can bury the whole thing and not have to worry about the exit line being so close to the surface?

Hi,when yo start clean tf1 filter you need turn off all system?

Amazing demonstration. Thank you

Excellent demonstration of how the system works!

Hello ,,what about when the unit is not operating ?? Can you push the charged lines back into compressor any other way ? With a vac pump ? Or is that sucking only and cannot push , gas back unto compressor ??

Cap is great!

You need to be EPA type 2 not necessary to be EPA 608.

All I have is a digital guage set, no vacuum guage. 16:00 is amazing advice, thank you!

Of course they use a Dunkin’s cup! You guys know your stuff.

Looking good Eric!

Mantap

Won’t buy

Going to be changing the main control panel this week, how do you get into setting up the parameters for the new control board?

Well understood thank you.

Thank you for a very good explanation of a device that I have and never knew what it was... Home was built in 1979 and I need to do some research on the drain and it's discharge and ensure that I am not getting any sewer gas returned to the house thru the trap...

A++ VIDEO

How would you do a pump-down on a multi zone mini split?

Good thank you

That wasn't a tiny release of refrigerant... That was venting... Your the trainer??? WITH NO GLOVES...

Yeah, how do you connect to it? Nobody helps me. It would be nice to know what the error code is. This boiler gives me so much problems in the 1 1/2 years I've had it

Great video!

Is the blue gauge closed or opened?

I just installed a new one of these for a pet supply store because the one they installed a few months earlier cracked flooded their supply room. The new one immediately started leaking from where the light grey bottom connects into the black head of the unit. It won't stop, did I just happen to get a second bad unit from the factory or is there a common cause for this?

Do set it for cooling when doing the retrieval of the refrigerant back ???

This is going to be big in the energy efficiency game! A must have for any energy efficient building!

How about the app! How it works?

I have had my Superstor -40 for 23 years. Great piece of equipment. I’m just having a hard time finding any literature on it. Like does it have an anode rod? I dug out the plug and foam at the top but there was nothing there. Knowing How long it should last and how to service it would be great!

I still have a leak after cleaning my filter 😬

Is this compatible with new yorker boiler?

The idiots who installed my boiler in 2006 did not put it up on blocks or anything to even allow access to the drain on the bottom of the unit. The drain line runs on the floor to a drain about 2’ away. So maybe 1” of drop from point A to point B. The drain is in cement that goes 3’ over to a sump pump and basin. How can I get a condensate neutralizer in this setup?

Thank you

We install a ton of these tanks all around the South Shore and they are great! Typically installed in an apartment with 1 or 2 bathrooms, and 1 hydrocoil for hear (we add the hydro kit). These are perfect for those situations. Mark is a great guy and really knows the HTP products. He is always willing to help out if you are having issues and can't get a hold of HTP Tech Support.

Dear HTP Management- I am writing this as I sit here with NO HEAT AND NO HOT WATER once again... I am currently on my 3rd HTP on demand boiler in the past 5 years - yes, I have had 3 units installed in just 5 years!!! While I appreciate you replacing these pieces of garbage under warantee, I have had to pay plumbers to install 3 times and also pay "restock"" fees at the plumbing supply house each time - I am into this for thousands of dollars. This most recent install was done in June 2023. It hasn't even lasted 6 months. I am disgusted.

will this pump 140 ft with not much lift?

Recently installed this unit with a incoming Caleffi PRV set to 25 psi on the Inlet, Pump runs CONTINOUSLY, and the Outlet Watts Water Pressure Gauge states 80 psi. Cannot get the Pump to Idle and illuminate a SOLID Green Light. Thus far, Franklin Electric Service Dept. can only say clean the Flow Piston, pump works well, but it just wont stop running and set idle. This is a new construction build and only three fixtures are opened thus far, Shower, Toilet and Hose Bib, nothing is leaking, using Uponor AquaPex.

Can you add system inhibitor through the TF 1 ?

Many thanks for such an informative video. What some of the other videos on here fail to mention is that the black screw cap at the bottom of the device is also the drain handle. Thank you so much for that part of the video particularly. I cleaned my Fernox TF1 this morning and also replaced the O ring. Many thanks again, Nig, England

Why do Americans drone on and on, taking hours to tell us what can be explained in minutes.

How do you increase the pressure, by turning the screw clockwise? Mine is at 10psi, I need to get it to 12-14psi. Also, what do I do with the quick fill lever while adjusting the screw?

But, you didn't make it compatible with the #1 thermostat in the market, the Nest 3rd Generation.

I thought the oil in the vacuum pump is to lubricate the vanes. Yes some types of oil absorb moisture. tho I don't see how that affects the air pressure or vacuum suction, and the valves are closed.

Haha why leave the compressor running when you have both service valves closed? Pull disco then close suction service