Are you able to fix a toy like this that isn't loud enough, OBNOXIOUSLY loud? I want to make my My Singing Monsters singing maw figure as loud and as obnoxious as possible.

you sell it?

Do you sell it?

If you were going to build this now, where would you get the propeller and mounting hub?

I get no sound from my Miata after my new double din any help?

Would a higher hp motor equate to more speed?

how to connect two cables for the antenna if the switch has three inputs, I did it and it doesn't work, how do I connect the third input

Hi what is the yellow block for smoothing the paint can you use this for any painted parts were can you buy and what do I type thanks

Thank you! I'm about to replace my factory radio & tape deck with a "modern" double-din. I especially appreciate the how-to with the antenna switch! Thanks again.

be very careful when using the screw driver on the apu, as u may scratch of a trace.

This video is so old I’m not sure you will even see this but will this work for drilldozer on gba as well?

Thanks for the video I'm thinking of putting a new head unit in my 10AE also.

UH-0H

Muito interessante

Waste of $$$$ purchase a real one!

Would love to see more of that project.

So I installed a Sony head unit very similar to yours but it’s the 1000 model not the 100. And It worked fine. No bypass or anything. But now the Bose speakers have failed and I suspect it might be because of the head unit and the amp working together, so I was confused why so many people were talking about bypassing the amp when mine worked just fine with everything plugged in… So since the factory Bose speakers are now shot then now I actually have to install speakers and I think the Bose amp sends a 5ohm signal to the speakers and most aftermarket speakers are 4 or 6 ohm not 5 so it makes sense now that you would want to bypass it… However my question is. Can you actually just skip the amp and play the speakers off of the head unit? Does the head unit have an amp built in?

Parking brake wire does what?

good video good job and thanks for refreshing my memory on this. but just FYI you have the jumpers pined out of phase

So you got it built, got it up on the air cushion, even verified that it would move. Why not climb in and run it?

Nice to see somebody using an antistatic mat and strap during a tear-down. I cringe at all the others that use no protection for the sensitive components.

Great video! I have an NB1 and installed the exact same AX1000 Sony head unit. I am using the factory Bose speakers so I connected the blue HU(headunit) wire to both the power antenna (blue) and amp (blue/white) on the metra wire. I have the shorty antenna but to get the signal boost it needed that power. Also for the ground, I ended up using a end plug with an o ring and grounded it to the metal frame on the inside. Is that okay? I didn’t even think to find a spade connecter to use that factory ground wire.

my one x keeps freezing on loading screens with audio buzz in mxgp and supercross games and kicks me back to the home screen,the xbox is super loud when this happens,but why only in loading screens? gameplay always fine

Did you have any problems with the way you wired up dimmer and illumination?

Thank you so much for this video. Your method of jumping the BOSE amp connector is far more convenient and posterity secure than simply splicing the wires. I did this on my 2000 Miata LS. Now time to run an amp! Thank you so much :)

Thankyou your video gave me the confidence this morning to do the same to my xbox 1 x scorpio edition.took me 4 hours. But it runs so smooth and quiet.thanks;)

Nice

I always put a tiny dab of thermal paste onto the pads aswell works wonders

Thank you! Your video is very helpful. I will try out what you did this weekend.

Great stuff! I dont have a loud fan, but I have hard crashes with NO overheating messages. I also dont believe the exhaust temperature is unreasonably high. I'll give this a go and see what I get. I cant find substantial evidence pointing to power supply issues with the internal supply models.

Re the oxidization, I have seen this on almost all xbox one motherboards.

The heat sink was supposed to be liquid filled. Not sure if they ever were though.

I think your's is the first video I've seen where Anti-static gear has been used. Well Done. One tip is to use a plastic scraper NOT a metal screwdriver to remove the old thermal paste, also an old toothbrush works with IPA. HTH

What do you use to clean the cpu?

Any issue with wind noise while top-down, Isaac?

Not sure if it helps anyone doing this in the future, but......If your worried about how much thermal paste to put on: Put a pea/bb size drop on the chip Keep the board elevated, place the heat sink on the board so it rest on the chip using just the weight of the heat sink Take the heat sink back off Use a q-tip to remove excess paste around the sides of the chip Put the heat sink back on and secure with the clamp Another tip. You’ll notice the thermal pads might have indents on the corners instead of evenly spaced because they aren’t centered over the components. Take the pads off the heat sink and place them centered on the components before you place the heat sink back on and secure with the clamp

Any chance I can just use bubble gum to connect the contacts? Hopefully there's some truth to these cartoons.

I changed the thermal paste on mine as well but it was still overheating. It's out of warrant so sending it to Microsoft is out of the equation, the country i am in doesn't have a service center anyways. What I did instead was disconnect the pulse modulation pin from the fan connector and that seems to have done the trick. It's super loud yeah but I have not had any issues since. The air is now cool even after 2 hours of gaming with a 4k hdr game.

Does any know how thick those blue thermal pads are? 2mm 2.5? IDK

hey guys my xbox one x overheated on fortnite last year and i took it out for repair and it got fixed and then this summer 1 year later it got overheated again on warzone power drained it then played warzone for the next 2 months now its overheating inthe pregame lobby should i send it to a local technician or a official ?

Great walkthrough! Question, I am going to replace my thermal pads soon but should i also get a new wireless card? My controller/headset will start struggling to stay connected when the console fan has been on for awhile.

Arctic Sliver 5 thermal paste works way better than Arctic MX-4. My consoles run about 4° cooler with Silver 5 then they did with MX-4

1 year later and the Xbox is still going strong. Haven't had a single shutdown issue since. Here's a great teardown video that goes into a lot more detail on how to remove the heat sink: kzbin.info/www/bejne/j5DCo2uLn7upsLs

I just use toothpaste 🥴🥴

So I’m going to try to fix the Bose “midrange” speakers to hold up a bit longer before replacing. That said, what is the downside or plus to keeping that Bose amp plugged in after a new head unit is installed? Any help would be greatly appreciated!

Mine is overheating and turning off after i start a game i did replace thermal past but still same problem noisy fan and turning off after 2 minutes of starting game

I recently replaced one of these, using a motor from Digi-Key: www.digikey.com/product-detail/en/jinlong-machinery-electronics-inc/C1234B016F/1670-1085-ND/9974297

I’m going to have to embark on this journey with my Xbox one X as it is a late 2017 model and experiences overheating issues similar to the ones that you have experienced. I’ve never conducted any sort of repair like this before so please wish me luck as I’m very nervous going into this, regardless your video has given me confidence and I must say thank you for your hard work.

I love how the title of the video is the one thing that isn’t in the video. The unit magically appears mounted in the location . I’m having trouble finding clips to secure it tightly, the adapters my unit came with are too narrow so the head unit is loose

My Xbox gets loud on all 4K games but doesn't shutdown or overheat. Would this work to make it's quieter?