kzbin.info/www/bejne/foDVYmx5nqmFh6csi=ZkSYdR71YRZQsSAb

this has to be one of the worst tool demonstrations I've ever seen 🤣🤣 like, what is this? were you going for the "stop motion" effect? lmfao ... I'm almost certain you're supposed to show the tool being used, not skip through to different points of the progress 🤣🤣 ffs ... I think I know now why you bought the tool

Can I come

No.

Yep, thats me! It was on the street because we were moving in. Doka and van moved with us. Will be around on Saturday if you want to stop by.

@@MattofManyTrades Cool. Welcome to the neighborhood! I’ll try and swing by at some point. My Son is a fan of the Doka and spotted your truck and your channel sticker. Don’t see many here despite this being the VW bus capital. Sorry if this seems sorta stalkerish. Totally unintended. Guess it’s a VW guy thing. Haha.

@@ocavant not stalkerish. It is a VW thing. I super get it.

Your doors are probably inch and 1/ quarter inch and a half thick. I used three-quarter inch screws that were into three-quarter inch material so untruth only about a quarter of an inch protrude into the door insulation. What holds the racks to the door is not substructure or insulation it’s the sheet metal. Tap a little pilot hole and use sheet metal screws. Not self tappers. Don’t over torque. Just tighten them until they’re snug. These were up in my old shop for two years and the door went up and down every day. They’re mounted in my current shop on a 14 foot high rollup door that goes up two or three times a week there hasn’t been a single pull out or failure.

Probably. I had an auto focus issue with my camera and had a couple videos that I shot complete and just had to go with the footage that I had already shot.

Nice!!

Same. I know people complain about government oversight, blah blah blah, but it’s more efficient. It burns less wood and heats bejesus out of my house.

@@MattofManyTrades so true

I don’t, but it depends on your paint. A SW exterior house paint is thick as putty and would have to be thinned. I sprayed with a quality interior trim paint that is fairly thin - Ben Moore Advance.

I had something similar in a house years ago. That was a single story ranch. And it worked great. My current home is a bi-level mid-century, and I also have duel Heat pumps on each level with head units in each bedroom. The fans in them are super efficient and when I have the fireplace on I almost never turned the internal fan on in the fireplace, because it is a little energy inefficient. Instead, I’ll turn the fans on low in all the units on and open the doors and the heat circulates all over the house levels. Works great. I stayed in an A-frame once that had an 8 inch tube/duct that ran to the very top of the peak to almost floor level that had a fan that drew the hot air in the peak down. It made it super comfortable and fix the issue of the main area being comfortable and the sleeping loft being hotter than the fifth level of hell. The fan on the duct seem to have been a large DC computer fan, so I’m sure that it was just sipping pennies a day as well

The country where you get an inversion later in the air stagnates in winter, the only way that you can legally buy a woodfired heat source (stove insert, regular wood stove, pellet stove, etc..) is to have one with the catalytic converter, installed to reborn the particulates in the hot instead of venting. Most cities have passed similar ordinances from New York to Chicago to Dallas to Portland. if you live in an urban area, you can’t use grandpa’s potbelly stove that was in the cabin for 55 years. It makes it a little more complicated to light, but my home growing up was heated solely on wood heat so I have some experience and I will say that stoves and inserts with the catalytic converter I have longer burn times and I use less wood in them so they are more efficient and a better use of . I don’t like how much more expensive they are, and I think that the expense is directly reflective of the fact that they mandated by law, but the return of investment in comparison is only for five additional years and a good woodstove will last you for your lifetime. With the newer models, you may after 10 years have to replace the catalytic brick, but on mine it costs $250 is fairly easy to get to and I bought an extra with the stove and it’s on the top shelf of the pantry just in case I need it in a decade or so.

@@MattofManyTrades You must be in Canada. Wow. Even got the wood stoves. Ridiculous.

@@chrisragan9766 Nope. Oregon. Same rules in Seattle, Chicago, St. Louis, and even Dallas. Any major urban area.

Thanks Mason! See you there next year!

I wouldn't have even thought of not including it! Your photographed inner demon is full of love and generosity!

Thank you

Thanks. There are commercial options available now, but my home-built ones are still working great and are not plastic. Send a pic when you build yours :-)

Cinder blocks and boards are old school. IKEA is the new version.

you could, but would HAVE to add a face frame with the shelf biscuit joined into the back of the face frame. Done for reinforcement. If not, the shelf WILL bow.

I did not. That would would flip me out as I would think that it would have a reliability issue connected to the sensor. I would call SawStop TOMORROW!

Nice! Yep, the Engine stand Method is the way to go. I just sold this bender (not the dies) to a local guy and I and upgrading it a little and will build version 2 on the engine stand.

Thank you. No, I have not had that issue.