Awesome used on a n old clicker remote I found abs craftsman’s
@raygolf19 ай бұрын
Things I learned the hard way. 1. Chamberlean, Sears Craftsman, LiftMaster, Master Mechanic & Do It Manufactured 2005 to present with PURPLE smart button is ID: 3 Problem 2- When putting in your 4 digit code hitting # THEN id NUMBER (IN MY CASE NUMBER 3), THEN entering # YOU Have 5 seconds to do this or start over. Problem 3- Don't attach the Keypad to the outside first- rather, have the key pad in your hand 2 feet from the garage door operner unit. Also, Start the set up with the GARAGE Door DOWN. Hope this helps. This is the little stuff that went wrong with me before it worked.
@obeid2 ай бұрын
I couldn’t find that opener id anywhere. You’re amazing
@markmulligan571 Жыл бұрын
Why isn't there an energy efficient remote clicker? Wind up, solar, recharge, like an emergency radio? Are battery manufacturers subsidiaries vertically integrated with electronics corporations? So every remote control is wired to eat up batteries fast?
@barbarasmart-mendoza9065 Жыл бұрын
I don’t have the clicker id or instructions. Where do i find id number to reprogram?
@davidbraun1404 Жыл бұрын
Thanks for solving this for me!👍👍👍
@EJSDesign2 жыл бұрын
The potato you used to record this should be retired.
@wesvyverberg95172 жыл бұрын
followed instructions but it would not activate the opener.
@wesvyverberg95172 жыл бұрын
took clicker out of package, can't get the cover to slide off to even begin programming. love the comments on this thread, in particular the one about burning down the garage or the one about rolling over clicker with the car to solve the problem. Anyone got a hot tip on how to slide the cover off. Maybe a crow bar?
@wesvyverberg95172 жыл бұрын
butter knife to the rescue may need to grease the channel on this sucker
@aslamalalo90832 жыл бұрын
Cute and accurate
@johncraig53722 жыл бұрын
Thank you! The only glitch was user error!! Otherwise - all good.
@PatrickSalisMEDIA2 жыл бұрын
THANK YOU for the excellent knowledge transfer.
@theleroyshowkid8395 жыл бұрын
Thanks for this video, worked perfect!
@rfahlsing5 жыл бұрын
Much better quality video from the manufacturer: kzbin.info/www/bejne/gZfZgHiCqKlrsLc
@ranstu66235 жыл бұрын
You are showing a how to do video with such lousy quality video. Redo.
@slimslida5 жыл бұрын
I don’t have the owner manual to the remote how can I find the code
@cherylnespor88616 жыл бұрын
My original 2-button remote is lost. How do I program the gate to my community without it?
@amandaerwin89346 жыл бұрын
Thank you. Worked perfectly the first time.
@laforgia16 жыл бұрын
Thanks
@edmashmann75877 жыл бұрын
My pin did work but now it does not. I tried to enter a new pin but the pin doesn't work. And I tried to restart the process but the keyboard does not stop blinking. What do I do?
@ajshomemovies53027 жыл бұрын
I need to buy one---but how?????????????????
@bv40987 жыл бұрын
Thank you sooo much for this video, this really helped us out. :)
@aimeesnow9437 жыл бұрын
I just bought a new home that has this - does anyone know how to RE-program it with a new code???
@RobertLeachman7 жыл бұрын
It seems there are a few different models and they all look the same as near as I can tell. For sure the different models reprogram differently. After tearing mine off the wall to get to the model number (on the back only) and determining ours is a KLIK2 version I found the KLIK2C instructions worked. This model's reprogramming was distinctly different than the (random) one I found from the first Google search. When the thing was remounted I stuffed the relevant instruction in the battery compartment for the next owner. The happy news, with the correct instructions in hand it was a snap, good luck!
@marcbouge87027 жыл бұрын
Robert Leachman
@supermoistdeluxe7 жыл бұрын
ended up burning the garage down after much frustration
@ofalllife878 жыл бұрын
I have a Genie garage door at the house I just moved into recently, and I can't seem to get this to work at all haha. I'm sure I'm doing something wrong. I got basically all the steps to work (or so it seems) except getting the genie to link with it. Does the door need to be closed? should the keypad be close to the receiver?
@RobertLeachman7 жыл бұрын
See my comment above. Doesnt' seem to matter if the door is open or shut.
@SirTalksALot018 жыл бұрын
Thanks for the video
@davebuskirk8 жыл бұрын
This is no help . Should have included a screen shot of the referenced user guides...
@thomasraven8 жыл бұрын
I have an older Genie Intellicode. I followed the directions but the clicker still won't work. I can see the LED flash on the Genie when I press the remote button but it doesn't open the door. Looks like this thing simply doesn't send the correct code.
@davidhuff29399 жыл бұрын
Instructions were correct, you have to know which ones apply
@13brakeman9 жыл бұрын
Worked when I unplugged overhead unit and plugged back in then pressed learn button. After that I did the steps listed in manual. Hope this helps someone having issues connecting like I was.
@juliocabrera30539 жыл бұрын
Hi, How could know if my clicker is compatible with my opener? I have a Merik opener and I have programed a chamberlain remotes with out any problem Thanks for your help
@aaronrademaker19399 жыл бұрын
I was able to program my craftsman to open the door but for some reason it wont close the door. Any helpful tips?
@tamika79328 жыл бұрын
Did u figure this out
@marcelinobernardo33435 жыл бұрын
I got the same problem
@susand76399 жыл бұрын
Thank you Thank you to those knowing the instructions for the Genie Excelerator 1 up 2 up all others down works!!!
@jhernandezjuarez9 жыл бұрын
GOT IT!!!! THANK YOU SOOOOOOO MUCH!!!!
@leearmentrout42689 жыл бұрын
I bought this remote and now that it is programmed the one remote that I had doesn't work anymore. Is there anything I can do without buying another remote?
@t.j.leitch43119 жыл бұрын
Will the other remote work when I program my new one. I want both of them to work.
@mtvillageva10 жыл бұрын
Boy I sure feel like a dumbsky cuz this ain't working.
@glorialoflin194810 жыл бұрын
Please help me
@glorialoflin194810 жыл бұрын
I got the door to open but it won't work to close it
@Itsbillkaduru10 жыл бұрын
thanks
@juanluna331010 жыл бұрын
I purchased this item and it appears not to be compatible with the Marantec M4500 Garage door motor? please advise is anyone knows? thanks
@TherealDeltaEcho10 жыл бұрын
We have had ours for almost 8 years. Working two doors and in and out dozens of times every day in 100 plus Arizona sun. Never a single problem except you have to be patient if you hit the wrong code so the unit can reset. A little tough to do at midnight with coyotes howling! But just now we are having a tough time getting it to reprogram after changing all the door codes? But the video really helped. thx
@MariaRomero-zm3mb10 жыл бұрын
@MariaRomero-zm3mb10 жыл бұрын
@kemolud10 жыл бұрын
Thanks. This video was very helpful
@swankdogg10 жыл бұрын
I just ordered an 877Max for my Liftmaster!
@thevigilante30310 жыл бұрын
This video was very helpful I was able to set this up in about 20 minutes with NO help from anyone.
@danese16369 жыл бұрын
I spent 2 hours with no luck :(
@36811199910 жыл бұрын
It worked for me very easy to follow
@davidolsen881110 жыл бұрын
I bought one of these today for my post 1993 model Chamberlain (Type 4), and tried programming it to no avail. The opener wouldn't accept the new remote, and would wipe out the existing remote's codes so that it would not work and would need re-programmed. My house was built in 93', so I am wondering if my opener is maybe in a "grey area" in technology? The remote that came with the opener when we bought the house a year ago works, but I am having a devil of a time fining a second opener that works for this unit.
@swankdogg10 жыл бұрын
The Hell with that clicker! Return it!
@davidolsen881110 жыл бұрын
I plan on just replacing the whole works this summer, and get something with much newer technology.
@charleshaynes134710 жыл бұрын
I have a KLIK2 and I've misplaced my manual. With my new garage door I will need chart #4, which is a Liftmaster opener. Can you tell me the entry ID code, which is step 2 for programming. Thanks