Tiny Machines 3D

Пікірлер

@Memes-jn2sf 6 сағат бұрын

I thought this was auto leveling not manual

@henrip4097 3 ай бұрын

Is it possible to get these fan duct files somewhere? I had them damaged in the heat from hoten without sock.

@alpscraftshack599 4 ай бұрын

What has happened? You have gone silent. Are you still around, or did COVID get you, like it did to a few other 3D Printer Channels I used to watch?

@pires53 7 ай бұрын

What is the improvement on this?

@goldenfox334 10 ай бұрын

well i just learned the tevo tornado uses the exact same mount lol

@tonyja-lb3sm 11 ай бұрын

I recently purchased crx model but the micro sd card is not detecting Please help for this problem

@ArhitectoR Жыл бұрын

уважаемый где модели stl

@jdakid156 Жыл бұрын

What motherboard is this? Where can I purchase it?

@firstnamelastname7756 Жыл бұрын

Can I install a CR Touch with this new mother board? If so, how hard is the programming? I’m comfortable with installation of many things, but programming always gets me

@dontbeje11y Жыл бұрын

Just put my firmware on. Noticed none of the numbers are displaying. Anything that is a value doesn't seem to display. Any ideas?

@normanziegelmeyer7693 2 жыл бұрын

Does the autoleveling on/off box in the printer leveling menu need to be checked for any of the meshes to be applied? I have a g29 in start code and printer probes the bed, but unsure of effect of the on /off function in leveling menu. Thanks

@pawpatina 2 жыл бұрын

Running latest firmware on ender 5 plus with silent board and dual Z... tried to change x and y offset for nozzle, now G34 fails and all zero's during bed mesh until it completes...

@xxxxzorroxxxx 2 жыл бұрын

Cr-10 pro v2 installing: Do I Remove creality Sticker bed plate off (clean and so on) do The procedure of installing cording to video and I’ll be good? Thank you William M because video don’t show that.

@jared6326 2 жыл бұрын

Can ANYONE help me update my firmware on THIS type of board? I can't find ANYTHING to make sure I'm doing it right.

@drakeblackk 2 жыл бұрын

5:13 the problem is, my z is not even starts to move... WTF

@tinymachines3d778 2 жыл бұрын

This video is for customers that purchased through Tiny Machines 3D. If you'd like to try our firmware, contact us at [email protected]

@drakeblackk 2 жыл бұрын

@@tinymachines3d778 Gladly i fixed it but thanks! :)

@paulfinch2539 2 жыл бұрын

hi where buy it in europe

@tinymachines3d778 2 жыл бұрын

www.tinymachines3d.com We ship to most countries besides UK right now.

@AndrewAHayes 2 жыл бұрын

What advantages does a V6 have over the standard Mk8 hotend.

@7kortos7 2 жыл бұрын

this has the same feel as "How It's Made"

@Mett-wt3xj 3 жыл бұрын

Clean install. Nice

@danz409 3 жыл бұрын

so... magicly have the mounting harsware?

@makerus 3 жыл бұрын

It's a dog, not a pig...

@MTEric 3 жыл бұрын

Great video, do you have firmware for the CR6 Max yet please?

@RabbitsInBlack 3 жыл бұрын

I think my printer doesn’t go down out of the box. Z goes up but not down.

@jeepmanxj 3 жыл бұрын

Does this firmware easily allow me to adjust esteps?

@ruanvanderwesthuizen2379 3 жыл бұрын

Yes

@roguerrerocr 3 жыл бұрын

Install perfect but with my CR10, pla+ filament don't adhere to bed!. Any Advice thanks.

@michaelmartin2565 3 жыл бұрын

I’m thinking we may need to scuff the PEI sheet with some fine grade Steel Wool.

@Explore531 3 жыл бұрын

lol thats I have done hitting the space bar when I was watching this video it helped me alot putting those wires back on thanks for this video

@thefender0327 3 жыл бұрын

What do you loosen in order to adjust both sides?

@cameronford6645 3 жыл бұрын

You probably shouldn't have to loosen anything, just twist the z-rods.

@vojtechjanjurecka7285 3 жыл бұрын

Hold up you dont have to do anything in the software of the printer?

@luislopes8404 3 жыл бұрын

0:30 You have nothing plugged on the add fan plug! This is the same as me. I had my extruder fan not moving, and thought it was because i had nothing plugged there... does your extruder fan (front fan) work?

@gabaktech 3 жыл бұрын

useless video my menus are not even close to that

@landfallstudio3482 3 жыл бұрын

Do you even have the correct printer? This video isn't useless to those that have this specific printer..

@emanuelcalderon 3 жыл бұрын

does any one have the fans stl?

@JaviBLENDer 3 жыл бұрын

i wish it goes like that easily but, it´s no like this. Because when you move the left part of the axis, the right axis, moves too at the same time some micrones or milimetres! may be in other way?

@iconoclast485 3 жыл бұрын

anyone have a link to the leveling gcode I can't find it anywhere

@TitoPopoy 3 жыл бұрын

G29

@AirMaxAtzeKtb 3 жыл бұрын

More ads pls

@MrRalliartevo 3 жыл бұрын

I'm new to this channel. What firmware is this?

@DrStoooopid 3 жыл бұрын

Your music is way too loud, I have to turn up and turn the volume repeatedly

@hockeyguy820 3 жыл бұрын

If your left and right Z rods can turn so much that the X axis gantry is so non-level (as you show in your video), it means you have some bolts loose. Check the eccentric nuts on the roller wheel assemblies (both sides) and check to make sure that the metal plates of those assemblies are firmly tightened into the aluminum extrusion of the gantry. When you turn only one side it should be stiff and make the other side want to turn almost immediately.

@hockeyguy820 3 жыл бұрын

I used the Creality branded CR-10 dual Z upgrade kit on my Ender 3, and the procedure is almost identical as for the CR-10 except for the orientation of a couple of bolts. I had to increase the Z stepper Vref. The two stepper motors were too weak at first and would skip. The original Z Vref was 0.55 volts and I doubled this to a bit over 1 volt on my v4.2.x driver board. The new stepper motor and wiring also caused the LCD display to get scrambled and messed up due to electrical interference, including random button presses. I fixed this by isolating the display from the metal frame where it is screwed on, using the plastic spacer found here: www.thingiverse.com/thing:3077155 I also replaced the two M5x8 bolts with smaller self tapping screws and plastic drywall anchors for electrical isolation. This totally fixed the scrambled LCD display. You could also use M5x8 nylon bolts. Update: I realized that part or all of the electrical interference problem may be due to the grounded metal case of the power supply having to be removed from the frame in order to position the second stepper motor and lead screw. So another possible solution is to ground your frame to the power supply using an extra wire but I have not personally tested this to be sure it fixes the scrambled LCD display.