Will he ever learn....?

Carburetor tuning is such a lost art and it's really sad that so many have no clue on how to do it.

Available for the 83-88 Bronco II / Ranger?

Excellent video for your bumper mount Need a video one just like this for your hidden winch mount for an early Bronco

We’re all waiting for that video

Would like an actual installation video would help because black and white pictures on the installation instruction are terrible

would like a better step by step explanational video showing prep and installation of each component

Quality show

Thank you. Great video and most helpful. Any updates on the in-depth gear video?

Hello could you leave a link for the gears& true trac ,thanks already suscribe jorge.

You should have advised to check that the pitman arm is parallel with the centerline of the vehicle in case some knucklehead had installed it off a spline, or two, or more, when rebuilding or replacing the box, or the pitman arm. I've seen it happen and the steering gets really screwy. Otherwise, thanks for the video.

Just got done with the 2.5 lift kit. Getting ready for the heim joint steering system as well as the adjustable track bar end. These videos really help out, thanks

Had a great time! Can't wait until next year.

Some sweet rides there. Looking forward to next year as always!

I moved to Texas, so I am a little closer than I use to be. Hoping I can make it out next year. On the bucket list to make it there at least once. Looks like a blast!!!

Wow! This video made me pay attention to my suspension, yes I need these shocks and will probably get them, but I hate everything being black under my Bronco and wish y’all could offer them in white as well.

It was an amazing show.

Are you guys ever going to do a video on your floor shifter??

how did you get wipers on the bottom

Excellent job on explaining and adjusting steering…alignment has always been a sore spot for me.

Just installing mine now. Both calipers required a bit of grinding before they would fit into the caliper brackets

It’s huckel bearer which has something to do with carrying a casket

Does the seat sit higher than stock with this bracket?

I just finished mounting this and have a few thoughts to pass on - first off it is a seriously stout and well built product. For anyone considering a purchase be prepared to make some adjustments prior to all parts fitting together (it is hand-made), and seriously, do this before considering applying any paint. I spent some time grinding down sharp areas, and trimmed a section of the fuel tank skid plate for the hitch receiver to fit. Mine’s a ‘66, with a straight-ended bumper, which didn’t fit through the area intended near the pivot, so had to order an updated bumper compatible with ‘68 onward. The new bumper required some mods to align with all holes, plus I had to pound on the frame horns to allow it to slide into place. Hard to say how many times I took carrier and bumper on and off to get it right. Sounds like plenty of work, but now I have a tire carrier you could probably strap four spares to.

Bought the hood struts, wish you had the install video, I’m bad at paper directions.

Sigh...I love that smell!!

*buys stock in whatever tires company you buy from

Good product!

This was great. Definitely a James Duff commercial though. 😂

how many quarts of power steering fluid did you use total?

Congratulations! Awesome bronco! Loved the whole process put together. I just have one question. Where did you buy it from? I think I know the old owner.

where are you guys located?

Amazing!

So which is better,this or the duck tuff?Is the duff tuff more for off road compared to this one?

I’ve got a fever…. And the only prescription is more bronco! I’m bored without new videos. 😂

I have just completed my James Duff suspension lift on my '77. Getting ready to install the new Heim steering now. I will watch this a couple of times to make sure I have the steps down. I truly appreciate the videos here at Bronco Garage.

How far do I put the needle bearing into the spindle? Do I bottom it out?

Good work

I've struggled aligning Bronco doors on several Broncos over the years. This video saved me so much time. The rod thru both hinges is BRILLIANT. Thanks guys!

Nice video

My fullsize bronco has a 6” lift. How do I measure to get the correct draw length? Tganks for the video. Im ordering them as soon as I make sure I have the correct length.

How hard would it be to add hydro assist to this set-up?

I installed a 2.5” lift from Toms and unfortunately I didn’t grease the radius bushings no mention of it in the literature either … this pisses me off

Anyone looking for a bronco I have a 1975 that has been cut with rust but has 302 and 3 speed converted to floor from the tree. Hard top, hard doors, all glass. Rutherford County TN for sale. Let me know we can exchange info I have plenty of pics. Has clean TN title.

Bronco Whisperer? Seriously? Who was trying to kiss that guys butt! More like Bronco Procrastinator, Breaker, Dunce whatever you call him but he is not a whisperer. LOL

good end product. seems to have some quality control issues but its a good base to start with.

I'm looking forward to the EFI installation. Will you be using the dual tanks? I'd be really interested in seeing how you run EFI with the main and auxillary original style fuel tanks.

You haven’t ever tried a Quadratolet or also known as a Rottenchester? I have never had a problem at all off reading them. You can run them with the top off on a running motor. I had my rig running on its side only to have to shut it off because no oil on the top side. You will never find one better!

yall gonna start an OF?

So is the magnaflow the quietest? Which one would I choose if I wanted my 74 bronco to run quieter at all times? At idle, at 20mph and at 70mph? Just all around quieter. Right now it is incredibly loud. I know some people prefer that, but I do not. It wakes the neighbors in my apartment building when I start it and it sets off car alarms when I just drive by in parking garages. Thank you!