Bonsoir ou trouver le croissillonspour le meuble ?

I hate IKEA

How do you replace pop-up drain on these types of sinks?

Thanks for the video. I used this method today and it worked great. Great idea.

What do you do if a hump goes 90 degrees across your support frame 2x4s?

My ikea pipes are NOT 1-1/2. Much smaller. Less than 1-1/4, even. Don’t know what to do.

What a mess!

what do you do about the countertop? it's narrower(25.6") than the panels(26").

Thank you for this video

i guess, the cabinet support was installed incorrectly, Following Ikea instrcuction is very important. each cabinets should supported by 1 horizontal and 1 vertical support brackets (and each could be share with other cabinets) , the bracket needed to prevent cabinets move to all sides, the plastic footing only able to support the weight only, your one long bracket only protect the sides, but not front and back, if somebody kicked the cabinets from front , the cabinets will fall apart to the back and breaks the footings. the height of the support bracket is also too high, it should be the same or slightly lower than the height of the plint (8 cm). Why ? this will be a minimum adjustble height of your cabinet, you can't adjust the plastic footing lower than that. Cabinets don't need to sit on the support, but need to be screwed to the support, that screws prevent the movements. the weight of the cabinets supported by the plastic footing.

Very useful. Cheers.

I was looking for something exactly like this. It seems they discontinued the Omlopp though. Will this work with the MITTLED?

I need help putting in my wall oven. It is the same set up you have. Does it just sit on bottom of cabinet?

This information isn't in either the godmorgon vanity instructions or the sink top instructions. I feel for plumbers trying to plan ahead for this. You really need the parts physically on site before rough in begins

Great techniques and tips ! ... thanks so much for taking the time explain all the steps, you obviously have a ton of experience assembling these ikea islands, i'm so glad i watched your video, im confident that i can assemble my island thanks for sharing

the finish back panel should have the wood grain horizontal, so it look perfect, for that you may have to use two pieces.

You are the man!

I'm having trouble making straight and clean cuts in ikea material (melamine). What is your method and type of saw/blades you are using ?

You are an absolute LIFESAVER. Ive been building my kitchen island for about three days and I was getting real frustrated!! Came across your video and finished up CONFIDENTLY a few hours after that. “That things isn’t going anywhere!” 🙏🏻😂♥️

any particular reason you did not attach the sleeper to the floor ??

Most drains protruding out the wall is 1 1/2

How was the back panel attached to the 1x4?

Thanks for the Video! Over all it is very helpful. But one question remaining. Is the sleeper base screwed to the floor? How do you prevent the whole Island from tripping over if drawers with heavy goods are all pulled out?

Just the information I needed; I wasn't sure how to install a vessel sink with overflow. Thanks so much!

Is it possible to install Ikea water trap with a Duravit sink?

Very good instructions. Thanks.

Whats too high and what’s too low?

Is there a video after it’s done?

Thank you

Do you need to anchor beam to the floor? In case it’s moving?

Question or maybe I missed it, how exactly did you cut the back panel with the floor being sloped? Is the cut edge down facing the floor? My floor is very out of level but we used as much self leveler as we could and it's still out of whack.

Great video and detailed explanation. Thank you!!

After some planning I installed two lights connected to the driver and buried it all down the side and on top of the cupboard. But I'll be damned if was was to leave all that wiring under the cupboard. Yuck.

So if my wall pipes are say not perfectly aligned do I have room withing the unit to reroute some of the piping? I'm gonna install 2 Godmorgan side by side for a double vanity as the existing is a single vanity but with 2 sinks. I just wanna ensure it will work out due to limited space from left to right.

Hi, where did you get those 90 degree metal reinforcement corners for the middle section? I need those since I don’t have the back panel attached to my sektion box

Nice camera work and explanation! Great job!

Thank you so much - been losing sleep thinking about how I was going to do this!

Great vid - thanks! One quick question though, if I am installing cabinets on an island back-to-back, would I use two widths of 1x4 to maintain the right spacing for the side panels?

Thank you for the info. I'm saving it in case there's an issue with our install. We kind of panicked when we saw that the drawers would not accommodate our existing plumbing (and hadn't opened sink box yet to see that Ikea included their own pipes).

you are looking at this problem wrong. the t has to connect to the trap. you never address how to drain the far sink to the trap. i think you'll need a 90 degree left out of the wall. not ideal but i think you could make it work.

Where did you get your backsplash from? Thank you!

Question: Do you have a Video where you show exactly what you do after you cut the cable? Further, is it possible wire the cable directly into the transformer by skipping transformer plug/cable?

Thank you for the video. I see that you had trimmed off the top on both side of the oven cabinet. What kind of cooktop did you install? We are doing the same configuration with induction cooktop. Will I need to trim off the oven cabinet like you did?

I have looked all over the internet. I want to wire from one AC puck to another to account for varying distances in a closet. The shelf above will be in use so I thought I might be able to route the wires straight back to the wall to protect the wire nuts and connections. Can I wire from puck to puck like I saw on a van build using DC pucks? What do you suggest to protect the wiring on the shelf? THANK YOU so much!

Thanks so MuChhhhhhh my husband was going crazy with this installation and this helped a lot!!! We were about to return this because could not figure this out! Thanks agrian

Any chance you have an extra remote? Ikea doesn't make them anymore and my batteries leaked and I can't turn on my lighting anymore.

Basically you cut the plug and did a hard wire. Where the tips and tricks in this?

Who puts Teflon tape on compression supply lines?

What made you think you can get away with all that bulk wiring under there. That junction box looks like a fire waiting to happen.

Are you installing the Fixa brackets on top of the cabinet to make it flush with the other two metal support bars? This is so the countertop is supported everywhere.