Пікірлер
@Programcnc2412 2 жыл бұрын
Hi, i have a problem of 5 axis milling machine failure or mcode. Can you advise or solve it for me. Thanks so much!
@Programcnc2412 2 жыл бұрын
kzbin.info/www/bejne/jqXIdnmHmtqApa8&feature=share
@Programcnc2412 2 жыл бұрын
MAZAK VARIAXIS 730-5X II
@Programcnc2412 2 жыл бұрын
drive.google.com/file/d/1IK78zpb--XLf5_9YuCyMPqwmRrcw2WNz/view?usp=drivesdk
@smo3241 3 жыл бұрын
Can you make a video about tool length offset setting and programming?
@mateuszsiwek108 3 жыл бұрын
Roughing speed to high for this long tool assembly, but rest is looking great:)
@blackpanter8795 4 жыл бұрын
onzin zon ding kun je kant en klaar laten gieten beetje nawerken klaar
@gabewenaas677 4 жыл бұрын
The machine control/buffer cannot keep up with nc code! Try that same program in my MAZAK I 300 AWC w/ smooth control and same minutes!
@Thorhian 3 жыл бұрын
Dude, that's one of my dream machines for a business I want to get going down the line. How is it treating you these days? Did you go with HSK or Capto pallets?
@sofienguesmi7205 5 жыл бұрын
Belle mazak
@lumpygasinavacuum8449 5 жыл бұрын
Nice work.
@tanglaw9832 6 жыл бұрын
Like it …
@MultiMegawatts 7 жыл бұрын
Awesome demo, thanks.
@S.N.A.J.P.E.R. 7 жыл бұрын
dobre parametry łamie wiura
@caseylandis3561 7 жыл бұрын
100% rapid. Way to beat up your machines. Just because my truck says it'll do 140 on the Speedo I'm not gonna hold it off the limiter all day.
@gredangeo 7 жыл бұрын
100% Rapid is perfectly acceptable. Mazak has already limited the maximum rapid for you. If they felt you could go faster, they would have.
@dnm2795 6 жыл бұрын
If you don't run 100% rapid on production runs good way to lose your job.
@Cara.314 6 жыл бұрын
they are designed to constantly operate at those speeds. your truck is not.
@danm726 4 жыл бұрын
That rapid looks slow compared to some of bigger mazak the horizontals. And that tool change process is painfully slow. The door doesnt even open until the tool is sitting there waiting for the tool and then it even has to travel into the magazine still. Cool machine, but i disagree that the use of 100% rapid is "hard" on it.
@CNCSKILL 7 жыл бұрын
In a CAM program was written by the system to handle this part?
@baledefence1308 7 жыл бұрын
CAM Program was written using GIBBS CAM.
@lumpygasinavacuum8449 5 жыл бұрын
@@baledefence1308 I dont know gibbs. I wanna know gibbs. Thanks for machining porn.
@douro20 8 жыл бұрын
Do they typically machine those from solid?
@baledefence1308 8 жыл бұрын
Normally a Tee Piece like this would be cast and final machined if Required. As this was a specialized part and a small number was required, it was more economical to machine from solid. The added advantage is that changes can be made very easily if required and you are not stuck with the original shape from a casting.