They say not to spray water on hot bearings n parts, blow leaf blower or compressed air

Thanks for the demo and good/bad report. I see one of these on FB market for $1350 with 16 hours on it.

How’s this holding up? Looking at a used one.

Ive had my WM-8H about 6 years now. Pretty much every plastic handle on any lever has vibrated off and disappeared. Also the plastic covers over the bearings. And the threaded rod on the F-N-R lever HURTS when you back into it to dodge a limb and theres no handle. Prolly my biggest complaint is they should have used round-headed bolts like a carriage bolt in the feeding chamber, cause the square edged ones snag limbs _constantly_ forcing me to stick my hand in to pry them loose, and since I mostly chip hedgeapple, its like reaching into a gigantic medical "sharps" container thats also full of pissed off electric eels; and if you are lucky, it doesnt slice you to ribbons (or worse drag you in) when you break it loose and it takes off again (you cant switch the feed into neutral to do this or it will simply re-hook when you take your hand away and you wont have gained anything), also the thorns hang up on the lip of the feed chamber and its always on the other side from where I am standing. I definitely wear thick leather work gloves (plus goggles and earmuffs), yet still had so many glove perforations from thorns I couldnt use my left hand for a day, but thats the wood's fault not the chipper's. The spring loaded handle on top to let you raise the feed gear for large items bounces around like a madman while its running, be very careful not to be within its sweep especially with your head. Also the feeder loves to flail the wood back and forth as different elbows present themselves to the feed gear, this is also very dangerous with thorn covered wood. Basically stay forward of the opening (ie towards the tractor) as much as possible and wait for the action to die down. But having said that, I am very happy with the chipping once I can get the stuff into the chamber. It would be downright fun to use if I had skinny straight wood like in this example, pine or something I just just push in and walk away to get another. I dont know how many hours I have on it, guessing at least 50, the hour meter no longer displays anything; but it is starting to jam up in the discharge chute (4 times this week) so I think the knife has gotten dull, I also noticed the chips are looking more like long soggy strips like pasta now rather than small square-edged chunks like they originally did. Planning to change sides on the knife, which is why I am looking at chipper videos. I wish they had some sort of (optional) chute I could add on to direct the chips down into a trash can or something to make distributing them easier. I tried various sized drain tile with no success. So far the only thing I have successfully captured chips in is the 90" wide bucket on a fullsized backhoe, which works really well as long as you have a spare backhoe and a 30' x 15' space free beside your chipper to park it in, but most of the places I chip I can just barely get the chipper into, frequently have to dismount from the wrong side of the tractor cause theres no room on the step side.

Lightweight is good and what did I use it for it’s a lawnmower kzbin.infoUgkxTPN04aT-Qdjr_KS3ql7ng8wnU3wwsCqk also recommend Yes it is lightweight so hence not as robust as our old one. But if you take care it does the job really well.

Manual feed? Are not they all?

Thanks

Ran one of these on some black cherry a few weeks ago. One person running the controls and the other loading wood.. as fast as I could load wood on the splitter, it would be split and ready for another log

who gives a shit about your gloves

That’s how I use me front end loader too! I want a kinetic, so nice!

You said it's manual feeding and you didn't want the automatic feeding. Then you said it self feeding. I'm confused?

This is an older post but I think it’s very important to let everyone know it is very dangerous to place one’s hands on the ends of the log, sure the operator has to have a hand on the lever to throw piston but it’s always good practice to never load a splitter with hands on the ends of the log, was difficult to watch his hands in potential danger so often, if your hands are never on the log ends they can never be crushed by machine.

Sounds pretty much like it splits what my little WEN Electric 6.5 ton does. But like with that one, there are problem woods, esp anything with knots or odd things like that. I do have to say I hate splitting elm.

I'd there an electric version of the 34?

Manufacturer comment about we don’t tighten bolts because we want customer to become familiar with all bolts is BS… what other manufacturer makes that claim??? Think about Ford making that claim…..lol…

awesome video thank you sir.

How you reckon this would work on dead bodies? Asking for a friend ....

Quality control needs a kick in the nuts!!!

I got one of them and for the life of me I can't figure out why they still use a manual belt tensioner! Nothing but trouble! All they have to do is remove the engine pulley and install an electric clutch like all new equipment has done. I burned up so many belts I put in under my tractor shed and never used it again. I'm old and can't change it anymore. Luckily a friend asked if he could try it and it caught on fire and burned completely up along with four acres of his horse pasture! I would like to get one with a remote control box, electric start and a ELECTRIC CLUTCH THAT CAN BE TURNED ON AND OFF WITH THE REMOTE CONTROL BOX THAT CAN BE MOUNTED ON THE TRACTOR! but until they make some changes I'm not gonna be getting another one!

Thanks for this video. It would be great to see a video of replacing the three knives if you get a chance.

'Made in the USA' meant something different, back in the 50s. #CutFromDifferentCloth

own a 7 ton hydrolic and a 8.5 ton rapid splitter.. main difference . constant 7 ton vs peak of 8.5 ton. when you hit a harder part your tons drop fast with a rapid splitter. i only use my fast splitter for pine wood types. i am busy with a diy splitter. i am using a 7.5kw motor. what is ofcourse really high power. i calculated with a stroke of 2 seconds over 50cm the pure engine power delivers only 2.8 tons.. i am planning to go with a 4 seconds stroke so i have at least 5 (5,6ton) of constant power. i am using a flywheel of a boat to have some extra peak power the idea of the high kw motor is that i can add extra weight on the flywheel.

You’re splitting perfectly clear ash, try putting hickory through it.

Why after the first split do you not put the halves back together and split it into 4 in one shot?

I'd suggest chipping off some of the paint around that support strut, and using a standard stick welder to close that topside off. I think folks have gotten a wee bit spoiled with the mig welders.

Use air not water to wash !

its great, but looks like it is not high up enough to clear large rocks.

What does this model cost brand new? The reason I ask is because I am looking at a used one for sale for $2500 and I don’t really know if that’s good or bad it looks to be in good shape he says he’s only used it about 20 hours and he’s done with it hard for me to believe that somebody would buy a piece of equipment like that knowing that they only have about 20 hours of work but that aside I am curious? also would like to know anybody’s opinion on buying this type of equipment used? Or should I just buy one new? Thanks any help on the matter would be appreciated

Trail means it follows behind the tractor or it must be towed.

Still have this mower? I have some questions about it I just bought one that’s in some disarray

Another good tip is have a pallet crate waiting and you can fill it and move with pallet fork.

You called it a "manual feed" -- I think you meant to say "mechanical feed". I've read some posts saying that the feed speed on this unit is too slow compared to the Woodland Mills hydraulic feed, but IMO the speed is perfect. Thanks for your excellent review.

Definitely needs guards removed somewhat regularly for cleaning

I have one of these mowers... Works very well... I have had mine for over 15 years. I've put mine through it all. Even heavy brush. Takes multiple passes . Just go slower..

Good job👍👍👍

Double U not Dubba U Manual not manule Notheen???? Checkeen????

Love mine. already have done 12 cords in 2 years. did some hackberry trunk pieces were 28 to 30 in in diameter. So huge I needed the laoder tractor to get them to the right height. at times you might have to 'hit' and retract the arm a couple of times but it powers through all types of wood, wet or dry. True Beast

Hey there 8 in is firewood 6 inches is firewood have a good day

Thanks for taking the time to make this video. I am likely getting the 8H model. Not to be critical of your choice, but my reason for the "H"... I have a lot of varied wood from a wildland fire to deal with. On the ten acres, most all of it burned over. I have some pine along with oak and manzanita. Burnt, dry manzanita is a very hard wood. The variable hydraulic feed speed on the 8H will allow a slow feed for the hard wood and a faster speed for the soft wood. The slower feed also reportedly makes smaller chips. The fire took my home, and in the garage I had, among a lot of equipment, the Woodmax DC-1260. I had some problems with it and their customer service was excellent. My wife and I have both worked extensively in customer service and we know good service when we get it! Why not another 1260? I have a 40HP tractor now.

Yes!! I agree with the comment below, FCLC Mankato . . . this is an awesome video, and very helpful too!! Quick and to-the-point! Thank you very much!

Good video, thanks for the tip on the switch.

mine starts but when i go to engage the blades it wont engage them.

I just bought one, it is being shipped in about a week. Are you still happy with yours? I've got tons of pine trees that need chipping..

I had to remove the 2 side plates. Whenever I stored it mice would somehow get in and make a home. I haven’t found any problem running without them. Great tip on the safety switch, I’m going to try that.

Nice demo of splitter.

Looks like that belt pulley is already starting to rust because of bad galvanizing. Goes to show just because it has Made In USA on it doesn’t mean it’s going to be great quality. That steel was probably made in India or Pakistan. They should start putting Assembled in USA on there.

OK, glad I watched because if anyone offers me a sycamore tree for firewood I will decline. I’ve never seen a log so small that gives so much resistance to splitting. Obviously, this would be challenging to a large hydraulic splitter as well. The true test of any purchase is whether you would purchase it again after using it and I have had this splitter for Many years and I would definitely purchase it again. Having the large table area is a definite asset.

I have had the hydraulic model for over five years and have around fifty hours on it. I don’t remember having to tighten anything, other than the belts. Maybe the Chinese have forgotten how to tighten bolts and screws. I always run it at full rpm and blow it out prior to storage. It was locked up when I went to use it the next time.

Split a few oak logs at side branches and show that.

I believe the instructions say to set the machine slightly lower than your PTO at an angle not to exceed 15 degrees.. looks like yours is set up slightly HIGHER.. Is there a reason for that? Your stiff leg is almost too short as a result.