Ай бұрын
7 ай бұрын
6 жыл бұрын
6 жыл бұрын
6 жыл бұрын
6 жыл бұрын
Пікірлер
@drpainjourney 2 күн бұрын
Many thanks for your honest review, you just saved me from using $2000 + tax !!!
@miguelcuevas2976 10 күн бұрын
You are the only other person I have seen talk about bambu data theft. The printer is a Trojan horse.
@makerscorner93 8 күн бұрын
I'm sure you saw all the "Bambu bros" jump in to defend their beloved company. Haha.. It boggles my mind how people are so willing to just blindly defend a company that doesn't care about them at all, just their money. Don't get me wrong I do like and use Bambu Lab products, but I don't trust the company at all. People need to realize you can like and respect a product, without being a drone for the company that makes it.
@MoonWind32690 13 күн бұрын
Thoughts of buying now? Most of the issues shaken out or is this still like buying into a beta?
@makerscorner93 8 күн бұрын
I have spoken to a few people recently who have been getting good printers from them now with less issues than most of the pre-order units. That being said, they go on sale quite often it seems, so I would probably wait another few months. Peopoly is actively working on changes and upgrades. I actually just received my upgrade kit last week. Just haven't had time to install it yet.
@cordawg89 15 күн бұрын
I think the technology is good and will make it to future printers (less moving parts always a plus). The execution is still in beta stage. At this point I’m more interested in how the motors perform compared to belt drive as down the road some company should have a solid implementation
@makerscorner93 8 күн бұрын
Agreed. I am excited to see where they take the technology moving forward in their next attempt (assuming they even decide to make another FDM printer)
@tasa4904 16 күн бұрын
The biggest weakness of this printer is definitely the load cell. The numbers that it reads can vary a lot when it's probing. I still get decent first layers and the prints stick, but I feel like it could be more consistent instead of varying between too close and a bit farther away. I think the second is that it uses some specialized parts. Like the load cell. Or the cabling. If the printer goes down, you need to get the replacements shipped instead of pulling spare parts from your other printers. They ship quickly, but it still takes time. I had two things fail on my printer and it took a week each for the replacement parts to arrive. I find it weird how I don't need pressure advance. Every time I try that test, I don't see a difference big enough to warrant setting this value. So it's been at zero ever since I got the printer. You do need to pay attention to the filament that you buy. The printer advertises amazing speeds, but I've found that if you don't use filaments designed for high speed printing and you try and push the limit, the filament starts blobbing like crazy once the printer goes overdrive and then the blobs start ripping the print. The y-axis has some nasty vfa on my printer. I plan to use the instructions on the peopoly wiki to tune it but I haven't tried it yet so I don't know how successfully I can remove the banding. That being said, I believe that the linear motors should be capable of this since I have no vfa on the x-axis. Overall it's a fun printer and it's my main one right now since I have some bigger prints to make and this printer has a larger build plate than my Voron.
@oleurgast730 16 күн бұрын
It is interesting all of the issues seem having nothing to do with the linear motors or it´s drivers. Imho Peopoly should have sold a XY gantry with drivers to replace the gantry a Voron 2.4 350, Trident 350 or/and Vcore 3.1 500 instead releasing a complete "beta" printer. It would have not only been cheaper, but also much more intersting for the still big group of tinkerers. You could combine you favorite bed, bed kinematic, printhead etc. For load cells: They have a massive temperature drift. I do not know how klipper handles it, but a few years ago I have seen a github project were a microcontroller sampled the load cell very often (about a thousend times a second) and constantly updated the middle value. The controller gave a signal on its output the moment the measured value deviated from this middle value for a certain percentage. A quite simple solution, if I remember correctly it was an ATiny chip. It´s quite good to use a seperate microcontroller for such real-time task instead using a multitasking OS. Sadly I do not find the github project at the moment. But I think the problem isn´t the loadcell itself, but the way the values delivered are interpreted.
@mrnukeduster 19 күн бұрын
What complicated belt tensioning have you had to do on the Bambu? Curious, I have over 5000 hours on my x1c and have only had to tension belts once, and it was like 5 minutes to do so.
@makerscorner93 18 күн бұрын
Some people have had relatively good luck fixing the belt tension, but spend enough time in various forums and you will find that most people have a very difficult time with it. The instructions Bambu Lab provides tends to give very mixed results. My P1P is almost always printing 24/7 so I have had to do it a few times already. It really is a very hit or miss process. That being said they are very good printers that I personally recommend to most people when they ask me what to buy for their first printer
@joecullen1120 19 күн бұрын
Awesome!!
@makerscorner93 19 күн бұрын
Thanks!
@chargerman426 Ай бұрын
I guess I'm lucky as I haven't had any of these issues. I do have bed mesh set to run just for the print area before it prints and I had the clicking from the extruder (Peopoly sent me a new extruder and its been great). Its been the most plug and play printer i've ever had.
@makerscorner93 Ай бұрын
Really happy for you that you got a good one. I finally had mine working pretty good and was getting ready to make a follow up video, but unfortunately I had a new problem pop up with my 24v psu. It's working again, but I absolutely do not trust this machine to operate unattended anymore.
@xXKisskerXx Ай бұрын
I have had some first layer issues, but, I know for a fact my belt tensions are perfect. At present time - I am upset that I seem to be accounted as a "Beta Tester" when my unit wasn't a beta unit- but a mainstream sold unit. It's good I get similar support, replacement parts and the like - but it's horrible if you .. want to print and there is an issue, after all - spending hours disassembling and then replacing parts or reassembling screws, is timely and pretty frustrating. (at current time, I am awaiting the new loadcell version as well as a Y-motor, as my print issues have just.. been horrific.)
@makerscorner93 Ай бұрын
Yeah you have the most cursed one! Definitely worse than mine. Been following most of your struggles on the discord.. Peopoly should really just send you a new one at this point!
@NoMercyFtw Ай бұрын
the 3 brands u recommended at the end , i have 1 of each lol
@makerscorner93 Ай бұрын
I bet they all wok pretty good! haha
@NoMercyFtw Ай бұрын
@@makerscorner93 yes they do
@makerscorner93 Ай бұрын
Hey guys my cooling modification for the electronics is finally finished. Here is the link to the files and parts list over on Printables! www.printables.com/model/911028-peopoly-magneto-x-electronics-cooling
@protec2869 Ай бұрын
How is the hotend Performance?
@makerscorner93 Ай бұрын
I wouldn't say it's horrible, but I also wouldn't call it good. It is solidly just "meh"... I can usually get 28 to 34mm/s of volumetric flow with the standard melt zone (which is way better than most other printers on the market), but it struggles to actually get the flow started. Peopoly is working on a new revision so I'm curious to see how well that one performs. On top of that there are multiple groups within the community that are working on custom solutions to replace the extrusion system on the Magneto X. I can't really give many details on either one just yet as I'm not sure how much I'm allowed to share, but what I can say is while these things usually take a bit of time, there are a lot of really smart and talented people working on it and they are actually making some pretty solid progress so far.
@protec2869 Ай бұрын
@@makerscorner93 so the new machined which will drop soon will be updated?
@tempacc9589 Ай бұрын
With a printer like that you should get some B-Roll to dub over. Not nearly enough sexy magnet footage in this video.
@makerscorner93 Ай бұрын
Unfortunately not enough footage of the machine actually working yet lol. I have my machine finally in a mostly functional state now (after a long 2 months of troubleshooting) so I plan on doing a follow up video with a lot more footage of the actual machine. I mainly wanted to get some information out there since Peopoly is now selling to the general public and I wanted people to be able to make an informed decision whether or not to purchase it.
@theVariedLife Ай бұрын
I was wondering where the Magneto X went. Lots of hype but it basically disappeared. When they couldn't get a working printer to trade shows that was enough for me to write them off. Thanks for the review and all the work and info you put into it.
@makerscorner93 Ай бұрын
If I remember correctly, they had originally started showing it off back in August 2023. It was supposed to have been released sometime in November or early December but they quickly realized that they had a lot more work to do than they had initially thought. That's why we really didn't hear much from them after September. I think the main problem just came down to Peopoly not having the required experience in FDM to produce something as complex as the Magneto X. The overall building blocks of a good printer are there, it just needs a lot of little tweaks to get everything working as it should. Given how complex the Magneto is, I think Peopoly did an overall decent job, but they really should have done more internal testing rather than dump that job on the pre-order customers. Thanks for watching!
@theVariedLife Ай бұрын
@@makerscorner93 I agree its not ready and with the high price tag that tends to leave a bad taste in peoples mouth. This might have been good 10 years ago when tinkering to get printers working was ok but know the standard is 15 minute setup and producing quality prints quickly. They have a lot of work to do.
@No0o0o0o0o0 Ай бұрын
$2000 and it isnt a consistently functional product. 🤦 Thank goodness for testers, volunteers, and lets be honest , suckers who dedicate their time, money , energy and labor to fix a multimillion dollar companies products. This is one of the strengths and flaws of the 3d printer community. These financial juggernauts are offloading R&D, testing, safety, labor, liability and other costs to the users instead of shipping a fully functional product.
@makerscorner93 Ай бұрын
Glad to be one of those "suckers" so others don't have to be! lol.. Honestly Peopoly jumped the gun on this one. They really needed more time to smooth out all the rough edges. Hopefully this will be a learning experience for them, as much as it is for us. Thanks for watching!
@No0o0o0o0o0 Ай бұрын
@@makerscorner93 When this this is finally complete it will be a beast. Thank you for your service. 🪖lol
@pretzel_tfg Ай бұрын
Just saying, they're not a multi million dollar company. I think there's about 6 employees aside from people doing the assembly, and even then I think that's only 4ish more people. It's a small team that doesn't have a ton of profit, especially as currently they are sending out upgrade/replacement parts free to current magneto owners, which is really great of them, but they're no prusa or bambu in scale
@infowolfe 25 күн бұрын
we didn't pay $2k on preorder
@ashleys3dprintshop 25 күн бұрын
@@infowolfe Whether it is 2k or 1.4k does it even matter at this point? Do you have a fully functional product for what you paid?
@skysi Ай бұрын
an amazing review. big youtubers should take note. everything i have seen from them about this printer was super bad. you earned your sub and like for sure. good job mate, keep it up
@makerscorner93 Ай бұрын
I really appreciate the compliment. I haven't done any video work in a long time and was a bit all over the place during recording and editing. Definitely not "like riding a bike" haha. The Magneto X is in a bad place now, but the community is making improvements almost everyday! Even Bambu Lab had a few hiccups when they first launched (although admittedly not as bad as Peopoly). Give us a few months and I'm sure this printer will be worth it! Thanks again for the support!
@AwwwSnapperz Ай бұрын
6:21 "unlike other popular 3d printers out there, that basically force you to upload all your files to their cloud just to start a print" It's been 2 years since Bambu lab first launched in 2022. You have NEVER been forced to use the cloud to start a print. Sd card, lan only , even sending files over local FTP is an option.
@makerscorner93 Ай бұрын
Yes there are other options however SD card is a pain in the butt and means no remote starting of a print, LAN only mode as I had mentioned in the video is not as secure as most people think as Bambu Lab has been caught in the past still scrapping data from people using that option, and while FTP is an option, it is not one that many people are even aware of. I used to use FTP but found it to be slow and generally unstable. Don't get me wrong, I love my P1S but I will never blindly overlook obvious flaws just because I like a particular machine or company.
@AwwwSnapperz Ай бұрын
@@makerscorner93 I have to disagree. When the printer is in LAN only mode it does NOT leak/send out data. I have run checks both at the router level as well as wireshark. You can check it yourself. Heck if you are extra paranoid you can disable net access from any modern router at the client level. I dont blindly believe any company or any person who hasn't shown proof of their assertions, so I ran my own tests. Whether you are on a Vlan, normal router or one that is completely disconnected you can run Lan only mode. I frequently do it at local trade shows with a pocket router with no net access. There was a ytuber saying much of the things you mention and he was incorrect but he did it on a site that knew he was nowhere near an authority on the subject. and he could not answer let alone prove anything as network traffic can be at the very least monitored even if you cant view its contents. Even the crew behind x1+ who had access to far more of the inner workings confirmed what I already knew. You can run the printers without Net access, it does not send out data unless the user initiates it, and you dont need the cloud for it to work.
@No0o0o0o0o0 Ай бұрын
You are speaking into the void. that cloud thing has circled the globe and back several times and even after evidence showing it is 💩 people double down on false info.
@Manimal747 Ай бұрын
Paying to beta test is always rough. Solid review.
@makerscorner93 Ай бұрын
It has been a painful and expensive journey being a "paying beta tester", but hopefully in the end it will be worth it!
@1288832 Ай бұрын
I am waiting for my pre -order, problems at customs when sending to the European Union:) nice review
@makerscorner93 Ай бұрын
If I remember correctly, the last blog post said they almost had everything sorted. Hopefully you won't be waiting too much longer!
@snapo1750 Ай бұрын
Would love to see Peopoly selling the Magnetic actuators directly without having to buy the whole printer 🙂
@makerscorner93 Ай бұрын
Unfortunately I doubt that will ever happen. They are a printer manufacturer, not a hardware manufacturer
@stratos7755 Ай бұрын
as far as I am aware, bambulab does not send anything to anyone...
@hawtdayum Ай бұрын
It's odd that creators are still trotting out that lie even to this day when it has been debunked for a couple of years. AWS is in the states but even then you can use it fully offline or lan only.
@LincolnWorld Ай бұрын
That sucks you went through all those problems. Every printer I have purchased over many years went like that. Except for the X1C. But I did wait to get the X1C until after it had been out for a year. I don't think I'd ever be an early adopter on any 3D printer again. Too annoying. I just want to print. Thanks for sharing your experience. Maybe in a year, the Magneto will be "worked out" enough for me to get one. I do love the idea of what they are going for.
@makerscorner93 Ай бұрын
I normally don't like doing the whole early adopter thing, but I wanted a larger format printer, and couldn't resist the pre-order price. I feel sure within a year the Magneto X will be in a much better place. Considering Peopoly has never made an FDM printer before, the problems we have been having so far are a bit expected. Working on this printer has brought up old nightmares of dealing with my Tevo Tornado! Not a pleasant experience to be reliving!
@dudea3378 Ай бұрын
Seriously, the X1C is the only FDM printer I've had that worked perfectly out of the box, and I also waited a year after release to buy it. I'm afraid that by the time the Magneto gets the kinks ironed out, a new large format printer with tool changer will be available. Hopefully Bambu's upcoming XL printer will have linear rails and a tool changer....
@russbarrow Ай бұрын
Seems like a lot of startup issues that can get cleaned up as orders increase. I think this printer belongs into the large format space somewhat justifying the price. I am curious who the manufacturer of the linear motors. I thought Peopoly mentioned the potential sale of these motors in the future. That would suggest that they are the manufacturer (which seems very unlikely). any ideas?
@makerscorner93 Ай бұрын
Some people had asked if they would consider selling just the motors. The response they all got was the very corporate "we will take your suggestion into advisement". Translation, probably not gonna happen.
@russbarrow Ай бұрын
@@makerscorner93 Do you see any markings or other insight into another manufacturer?
@grasstreefarmer Ай бұрын
I was worried about this. I wish they had just released the linear motors in some common sizes and let the community have their way with them. Releasing a whole printer just risks tarnishing the whole system or killing the company because of simple mistakes. I dunno maybe that wouldn't have worked but this is less than ideal.
@makerscorner93 Ай бұрын
They were a little too ambitious considering this is there first attempt at making an FDM printer. I feel confident that they will solve most of the problems over time
@filar3d Ай бұрын
review?? you literally showed like 10seconds of the printer on screen....sorry, but I don't wanna see your face for 20min on a product review, I wanna see the product.
@makerscorner93 Ай бұрын
You are correct, there wasn't much showing the actual machine. I've had this printer for a few months now and unfortunately don't have much footage of the printer actually working. For that matter, there isn't much footage from anyone of the printer working due to all the issues we have been having with it. Peopoly recently opened up sales to the general public and I just wanted to get some actual information out there for people to be able to make an informed decision if they decide to purchase a Magneto X. I have two more videos planned for the Magneto X in the coming weeks which will have much more footage of the actual printer.
@iceberg945 Ай бұрын
It is interesting my printer arrived in May and has be very reliable and robust. In an industrial setting sending data to a cloud isn't an option. It appears the washers were not on my load cell no clicking or under extruding. The only issue I have had is not being able to get abs to stick however my enclosure just shipped so hopefully that helps that issue. If peopoly did make changes and push them out that quickly it would be impressive.
@makerscorner93 Ай бұрын
Peopoly has actually been pretty good at making changes in a very quick manner. It would not surprise me if they did manage to make changes and push them out that quickly. I did not have any clicking from the extruder in the beginning. It happens over time from the vibrations causing the set screw to come loose. They may have already started adding thread lock to the set screws before your printer shipped out to you.
@bradnemeth1364 Ай бұрын
Great review. Printer with lots of potential. 5 great prints. Then problems start. Link to peopoly discord gives an invalid address. Can you -please post a link to a reliable discord? Thanks!
@makerscorner93 Ай бұрын
This link worked for me peopoly.net/blogs/news/join-peopoly-discord-community
@monkeywrench1951 Ай бұрын
Great review, I am actually looking at this printer as an option still to replace my X1C (I want a larger frame and not have to send my files over the other side of the world). However, I need reliability as even after a year 3D printing by myself, my tech skills only go as far as changing the nozzle/printhead.
@makerscorner93 Ай бұрын
The foundation of a good printer is there. It just needs a bit more polish. Thankfully the problems are slowly but surely being solved. I'm hopeful that between Peopoly and the community working together we will have Magneto working beautifully soon!
@AwwwSnapperz Ай бұрын
This dude needs to drop his talking points and actually give accurate info. Cloud has always been an OPTION but never required to print.
@makerscorner93 Ай бұрын
@@AwwwSnapperz I should have worded that better. It is true you aren't forced into using the cloud, but the majority of the people using those printers aren't aware of that. The overwhelming majority of people are very basic users who might not realize there are other ways to start a print. I will be more careful in my wording next time.
@SuperSchmudi Ай бұрын
Thank you for this review. I believe in Peopoly as well and together with the great community the X will be a very fast, reliable and unique printer in future.
@makerscorner93 Ай бұрын
I agree 100% it may take a bit of time, but we will definitely get there!
@SkateSoup Ай бұрын
Oh you're the one working on the cooling thing, I'm really looking forward to that because <redacted> that 48v power supply fan noise. A solid covering of the highs and lows so far. I've been good after replacing my load cell and toolhead board, but haven't printed a lot that isn't calibration prints since that. Hoping to do a bed mesh at my normal PLA bed temp and printing some other actual things this weekend. Once I've got that baseline I'll definitely be looking at some of the .cfg updates that folks have put together. Also will see how changing probe accuracy to .025 goes. It really seems a bit hit or miss with the QA on units that have gone out. As you said there's been plenty of people with issues, but some folks have been having a good time with theirs. Other than the possibly self-inflicted loadcell sensor probe issue I've been okay, fingers crossed that holds. I have my corner screws tight until the springs weren't springy any more, I'll keep your tension tip in mind if binding issues show up as I print taller things.
@makerscorner93 Ай бұрын
Yep I'm that guy! Haha. I am hoping to print and test my "V2" design tonight. If all goes well, I will post links to where you can download the files. The .cfg video will most likely be coming out next Friday. Want to make a few more tweaks to mine before recording that video. QA on the Magneto X has been super hit or miss. I agree there are a few lucky ones that got printers with zero problems, but the majority of us were not as lucky. Heck I'm thankful that my problems are on the easy side of things! There are some people who have had to completely disassemble their printers multiple times already!
@MarkMalley Ай бұрын
I also have my screws clamped down, as that's what the instructions (still) say.
@jmsether Ай бұрын
I think I fall into that last category of being able to fix this printer. I have done a number of mods and so far I am loving it. My mods still need a ton of polish before they are ready for the public though.
@makerscorner93 Ай бұрын
Yeah you definitely have enough knowledge to fix some of the problems we have been experiencing. Weird seeing you outside the Discord haha 😂
@hm5348 Ай бұрын
I've been waiting for a good review of this thing. Thank you.
@makerscorner93 Ай бұрын
Glad to help. This is the first time I have ever tried to make a review video so I apologize for any lack of quality or weirdness in it. I am not super comfortable in front of the camera! haha.. Thanks for watching!
@ellisgl Ай бұрын
Way better than my videos.
@NikLindsey2050 2 ай бұрын
As a video idea you could scale this up and make it into a side/coffee table
@makerscorner93 Ай бұрын
That's a pretty good idea. Maybe even hide some wireless phone chargers in it too? Thanks for the suggestion! I haven't been active in creating new content for quite a while now but I am getting ready to start up again soon. Already have my camera equipment out and setup for a few videos coming soon!
@NikLindsey2050 Ай бұрын
@@makerscorner93 I like woodworking and things like your channel this video just popped up in my suggested feed and I watched it you could possibly recreate some of your og creations now that you have had more experience. I have wanted to get into this to get money I can't find a job right now but in my area there is not a lot of people who would pay for things like this or other woodworking
@georgschmitz8690 2 ай бұрын
I'm looking forward to see something about the magneto x
@makerscorner93 2 ай бұрын
I wanted to have a review video out a few weeks ago, but there have been issues with my unit. Took a while to troubleshoot, but it is finally printing reliability now. Need a little more time to get some prints completed, so expect a review video within the next 7 days.
@makerscorner93 Ай бұрын
Review video is officially out! Feel free to watch it whenever you have time
@user-sg9re6cq7z 7 ай бұрын
Great job decorating with the projections and music 🎵
@makerscorner93 7 ай бұрын
Thank you. This was my first time attempting anything like this so I'm pretty happy with how it all came out
@accordingtoabe2211 2 жыл бұрын
how well did the epoxy hold the acrylic to the wood? i want to use this process to make coasters for my bar
@makerscorner93 2 жыл бұрын
The epoxy has held up perfectly over the years. Haven't had a single issue with it at all. Sorry for the late reply. Unfortunately due to life being hectic over the past few years I have had to step away from the channel. I have a number of projects coming up soon so be sure to subscribe for when I make my return.
@catzbest8050 2 жыл бұрын
This is super duper cute! I am making a bunch of these to give as presents for Christmas! THANK YOU!
@makerscorner93 2 жыл бұрын
That's awesome! They are so simple to make but are a lot of fun and very useful especially when the weather gets cold! Be sure to subscribe because I have a very big project coming up soon and I will be recording it all! It's going to be a fun one!
@vivekvarghese 3 жыл бұрын
What are the dimensions? Great video :)
@makerscorner93 2 жыл бұрын
I don't remember what the dimensions were but you can make it to whatever size you want. Completely up to the person making it
@maryjones5843 3 жыл бұрын
When you put it in the sink it looks like it's set into something, a can maybe? What is that? Is it for something?
@makerscorner93 3 жыл бұрын
It's just a cut down can to set a pot on top of with holes around the top edge to allow for some airflow. Hope you enjoyed the video.. It's been years since I have been active with the channel, but I'm hopefully getting ready to start back up again. Have some cool projects lined up plus one VERY cool (and quite frankly advanced) project in the works so make sure you are subscribed so you don't miss it!
@maryjones5843 3 жыл бұрын
@@makerscorner93 Thanks for getting back to me. I fell across you when I was trying to figure out how to build a tabletop indoor fire pit. There's a lot to learn if you're starting from zero. Alcohol doesn't burn like you'd think (or like an indoor city girl who' never done anything even remotely like this would think). I learned a lot from you. Thank you.
@kp-pi2zo 3 жыл бұрын
Badass
@makerscorner93 3 жыл бұрын
Thank you! I haven't been active on this channel in a few years, but I'm getting ready to start back up again soon! Make sure you are subscribed because I'm going to be doing some really crazy cool projects here very soon!
@packerjock 3 жыл бұрын
I love this, and made my own concrete bowl, however, the flame from the chafing gel fuel can is not strong enough to be seen. I removed the stones above the can, but the flame still does not rise enough. Does anyone have any ideas? Thank you.
@midlife_crossroads 2 жыл бұрын
You can use isopropyl alcohol
@makerscorner93 Ай бұрын
Sorry for the super late reply. I haven't been active on the channel for a couple of years (finally coming back to make content again). While I don't remember exactly what I had used to make the flames in this video, I am planning a newer version of this project and I will be sure to include what I use for the fuel source. Thanks for the comment!
@bloff2448 4 жыл бұрын
How did you get the flame so high?
@makerscorner93 4 жыл бұрын
This project was so long ago that I honestly don't remember what I used as the fuel source. Living in Florida, I don't use it very often. Sorry I know that wasn't the answer you were looking for. If I have time this weekend I will try to see if I can figure out what I used!
@Ghostridergt 5 жыл бұрын
Can we get a parts list an links maybe?
@makerscorner93 Ай бұрын
It is just wood, acrilic, and LED strip of your choice. No specific "parts"
@efsyoo 6 жыл бұрын
Nice video Ken!