I want this presentation to show that gt8 is the better option
@CooperMiranda-t4x21 күн бұрын
00211 Heidenreich Flats
@CharlesAllen-m2h24 күн бұрын
Terrance Ways
@FoxMilo-r5g25 күн бұрын
Weimann Shoal
@EdithLawrence-s3f25 күн бұрын
0427 Terry Drive
@SheilaSouthmayd-w1z26 күн бұрын
Walker Brook
@EmilyThacker-j8f26 күн бұрын
8391 Alfreda Walk
@KatharineLorraine-l9pАй бұрын
Eli Estates
@BryceBrandonАй бұрын
22939 Fadel Village
@OwenLance-l3nАй бұрын
Quigley Club
@PullanKerwin-i4zАй бұрын
Mustafa Bridge
@NelmuArinaАй бұрын
98562 Moen Port
@WilliamLopez-z8eАй бұрын
680 Batz Island
@HankRotundo-b1hАй бұрын
Brown Circles
@Yohannesmengesha-hs6rmАй бұрын
The manual in discription is gone when i entered the page throught the link there is nothing.
@Mary-Gonzalez-b9jАй бұрын
Vance Bridge
@Nikola__K2 ай бұрын
Grate job Came! Can you get a suggestion over to the team in IT? Add a option for automatic closing after opening + after the obstacle sensor has been triggered! Not just auto close after 10second, but auto close 3 seconds after sensor has been triggered and cleared! If you enable that option for lets say 3 or 5 seconds only after sensor has been triggered you can set the previous F19 and F20 option to a longer duration lets say 20 or 30 seconds maybe more. This makes it so if you exit the gate early the gate will close right behind you instead of waiting another 10 or 15 seconds. And you can set the previous settings F19 and F20 for a longer interval so you don’t need to rush, but when your car or bike clears the sensors the gate will close in 3 seconds after it has passed it, if you come back to the sensor it resets to the start of the 3 seconds again so not to damage your car if you are towing something or a truck is passing through, but if the sensor has not been triggered it will wait for the time specified in option F19 and F20 lets say 15 seconds before auto close.
@kieranbrown15063 ай бұрын
I have ground stops on the fully closed and fully open sections of my gates, when doing the travel calibration and the gates hit the stops will the board learn where the stops are located on the run?
@chrishunt2343 ай бұрын
Great video, thank you for taking the time to record this., it been really helpful
@akhterali87096 ай бұрын
How to configure came G4000 barrier left to right open
@luclecastor8 ай бұрын
Trio
@Asifonline-ig8mp10 ай бұрын
Thanks far information
@akshayrnair261111 ай бұрын
It is showing that the keycode is already in use wt can I dooo
@atheraliChoudhry Жыл бұрын
Gud job sir
@R.NavaneethaKrishnan-l6f Жыл бұрын
How we can configure master slave
@lisandracastilla5621 Жыл бұрын
This is a great video!! The only thing I could find online. I hope you had more. Thank you!
@TomaszChanke Жыл бұрын
it looks good!!!
@luismanuelperezmatos5491 Жыл бұрын
Buenos dias cómo le aumento laveloida para k gire mas rapido
@johnconnolly2424 Жыл бұрын
Excellent explanation thank you
@sharafyasp8475 Жыл бұрын
Why came board er7 error comming ,how to solve???plz reply
@jodicobb63822 жыл бұрын
This is how I've done life after the 1St. Fight with a Bully! Wanna play in my Yard? 💪😫😱⚡️💯✅🤜
@gege88462 жыл бұрын
Hello. What to do in "add automation", when i have supported control board, but not "gate+board". Do i have to do this via input/output configuration? My control board is ZL65, my "gates" are swing by ATS.