How to connect additional poco controller for more zones (more changes ) but controlled by one display
@LumitecLighting17 күн бұрын
The Poco Modules are independent of each other and cannot be connected together. Therefore multiple Poco modules cannot be connected to the same display at the same time.
@Jassman353628 күн бұрын
Looks good on that 23 Albury brothers.
@luisgverdiales1227Ай бұрын
Need to replace an defective Quattro 2 color how to remove old screws if stripped?
@LumitecLightingАй бұрын
Your best option is to drill the old screws out with a bit smaller than the diameter of the screw. As the screws are made of bronze a standard screw stripping tool may not work effectively. On replacing the lights remember not to use power tools with the bronze screws. Use a hand screwdriver to fasten.
2 ай бұрын
Do they need to be mounted below water line to keep cool? or can they be mounted out of water?
@LumitecLighting2 ай бұрын
They are designed to be used as an underwater light where the water regulates the temperature. They can operate above the water line but reduce power and output when they get too hot as a safety feature. We have other above-water products available at lumiteclighting.com
@juliettfernandez81702 ай бұрын
What is the difference between spot and flood light?
@LumitecLighting2 ай бұрын
The Spotlight has a narrower beam pattern and will project further than the flood option. The spot is ideal for a forward-facing light to detect markers and obstacles in your path. The flood has a much wider bean pattern with less range. It is perfect for an aft-facing light to illuminate the deck and area around the transom of the boat.
@scdrescher13 ай бұрын
Way more than I needed but absolutely worth the watch. Thanks for sharing!
@troyalstead14713 ай бұрын
The Poco 3 is useless, definitely not worth the money. If they ever add a timer / scheduling capability, it will be worth considering. But not until then.
@ar50004 ай бұрын
will it break if you force the light down as a result of hitting a dock roof or something rigid?
@LumitecLighting4 ай бұрын
If the impact is sudden and hard it may pop the release allowing the light to fold but if the movement is slow and progressive such as backing slowly against a garage overhang then it will most likely snap the shaft.
@williamchamberlain44415 ай бұрын
What is the recommended drill bit size for the 3 mounting screws?
@LumitecLighting5 ай бұрын
The size of the drill bit will depend on the thickness and density of the material you are drilling into. The typical range for fiberglass will be from 5/32 to 3/16. Do not fasten the bronze screws with a power driver but rather use a hand screwdriver. There is a sizing guide supplied in the instructions with the light.
@reddodge44238 ай бұрын
If the light draws 2.1 amps wouldn’t a safety factor be close to 3 amps if it’s 2.1 X 1.4.
@Z-Ack9 ай бұрын
Screwing fiberglass sounds painful..
@jemdost67249 ай бұрын
I can control connect any universal RGBW light that has the RGB wires and control them without limitations correct?
@LumitecLighting8 ай бұрын
I'm sorry for not getting back to you sooner. Simple answer NO. Poco is designed for a 2-wire system and uses a single-wire connection to the module to command the lights. You need to use Lumitec PLI-enabled lights to get the full functionality from the Lumitec Poco module. Third-party RGB or RGBW lights use a multiple-wire connection and are not compatible with the Poco system.
@Tigermeg8169 ай бұрын
Hoping these will work with Humminbird Solix soon
@ivanusztics8272 Жыл бұрын
Pictures at night??
@StinkyTeal Жыл бұрын
So without exposed fasteners, how can you remove it?
@LumitecLighting Жыл бұрын
It is just held in with spring loaded buterfly clips fastners and possibly a bead of sealant (optional). Break the bead of sealant , if used, and wedge a flat edge behind the lip of the light and as you pull forward the clip tension will compress and the light can be easily pulled out of the mount hole.
@SouthernSpeedVideos11 ай бұрын
Just pull it, the springs will straighten and it will come out.
@StinkyTeal Жыл бұрын
Even on your website you don't have a list showing which lights are PLI, so frustrating.
@LumitecLighting Жыл бұрын
Apologies! Under the "All Products" menu for all product categories, you can filter by PLI products. Also, in the specs of any product you may be interested in, it will state if it is PLI compatible. We are currently working on improving our website to make it easier to search for PLI (Poco Compatible) products. Thank you for your feedback.
@AnthonyCelata Жыл бұрын
I just bought 9 of these. Very Disappointed that I have to do this whole process every single time I turn on these 400 dollar lights. If there is a way to lock on a single color every single time it should be mentioned in the packaging. The comment below suggest there is a way but is written so poorly that it still leaves many questions. "No it is a manual process. However if you connect any compatible RGBW light to our Poco digital lighting control module you can pre-program the light to come on it any color or intensity you wish."
@LumitecLighting Жыл бұрын
Hi Anthony, sorry for any frustration this has caused. There is a way to reprogram the factory default setting to allow the light to come on in a set color or remember the last color selected. It is too much information to list here in the answer section but if you reach out to our customer support they can provide documentation to walk you through the process. Alternativly you can purchase a Poco module which will allow you to program your lights and control the color via a compatible display or through your smartphone using the app (not compatible with Quattro lights). Please reach out to our tech support for more assistance. www.lumiteclighting.com/contact/technical-support.html
@leandrozerbo8034 Жыл бұрын
good advice! I'm installing name lights on a 50+ million dollar yacht .. So im soaking all of this in like a sponge !!
@brynnagminalis7477 Жыл бұрын
I have 4 on my Yatch I use it as my main lighting control through out the entire vessel and have lots of lights hence the need for 4 of them, currently we are using iPads in different areas just selecting the poco device on wifi of the area needed, is there any way to connect them so they all show on one controller in one interface to control all units or is this not possible ? I really don't want to switch to something else but its incredibly frustrating if there is more of a demand for individual channels than one unit can provide having to switch between units in settings each time I want to control a different area.
@LumitecLighting Жыл бұрын
Ideally, you only want to use one Poco module on your vessel and spread the lighting load across all channels. Lumitec lighting with our PLI technology can be on the same channel yet receive separate commands from the Poco module, thus behaving differently, allowing them to share the same physical circuit.
@brynnagminalis7477 Жыл бұрын
@@LumitecLighting So basically no, if someone wanted to use your great product with that one drawback they would have no way of setting it up on lets say a mega Yatch that wanted to use your product because they would be limited by the easy to integrate through software function, of linking command actions to be sent across multiple IP's on the network.
@Floridaboatinglife11 Жыл бұрын
youtube.com/@Floridaboatinglife11 I love your videos. It has inspired me to start a channel. I have a long ways to go but I enjoy making the videos. Thanks again.
@LumitecLighting Жыл бұрын
Thanks, good luck with your channel.
@williamgleaton2992 Жыл бұрын
Lights draw fish, fish draw sharks so no swimming but alot of fishing. Unless your just a fresh-water fisherman.
@bradballard2068 Жыл бұрын
I'm not sure, but I don't think a pontoon is a ocean going vessel.
@seamanvlogsqatar Жыл бұрын
I always recommend lumitec
@Beenthere2xs Жыл бұрын
This was excellent advice! I had to drill holes in my fiberglass ladder to attach extension legs and the countersink bit was exactly what I needed. Thank you!
@beaud44742 жыл бұрын
Can you mix the the spectrum lights by having a lower lumen full spectrum and a higher lumen on the same circuit and control them together ?
@LumitecLighting2 жыл бұрын
Yes you can! As long as both lights are spectrum (quattro and X2 for example) you can place them on the same circuit and control them via our TTP technology (toggles of the power switch). Our spectrum lights share the same color cycle and will change color in sequence, however the Quattro is not a PLI light meaning it is not compatible with our Poco lighting control system and this setup will not work if you plan on installing a Poco module. TTP only.
@LumitecLighting2 жыл бұрын
If you intend to use lights that include PLI technology (Typhoon, X2 and Javelin) then you can use a Poco system. However at that point there may be alternative ways to wire and control the lights. You can check with our tech support line for more advanced methods.
@LuckyBuff49492 жыл бұрын
What works for me. Drill two sizes smaller than the screw size.
@JakeLemon2 жыл бұрын
Dear Lumitec, Do your Poco modules connect with Furuno MFDs? Thank you.
@LumitecLighting2 жыл бұрын
Poco compatibility for the more recent Furuno model will be available later this year.
@ryanwalsh53052 жыл бұрын
Need an actual video of it on at night shining out infront of the boat.
@zackworrell2 жыл бұрын
This is so helpful because West Marine does no justice to explain this, neither do other retailers
@carldensman40992 жыл бұрын
The beer wow it’s a deal what a sales pitch!
@blcouch2 жыл бұрын
Damn cool tip!
@LumitecLighting2 жыл бұрын
You can watch the full video here. kzbin.info/www/bejne/oZDceZ5-e5llfqs
@socalchaos7142 жыл бұрын
What push button switches did you use
@LumitecLighting2 жыл бұрын
For the purpose of the video we used a basic illuminated momentary switched from TE Connectivity. www.digikey.com/en/products/detail/AV1910P724Q04/450-2262-ND/6043749?itemSeq=375998740
@DavidWilks2 жыл бұрын
I want to add these to the Topper on my Marine Transport truck!!! AND of course on my boats as well. So often I am picking up or dropping off a vessel at a ramp or Marine Dealer after hours and the rear spreader light with be so amazing to assist with loading/unloading.
@LumitecLighting2 жыл бұрын
David, the Razor will run on a 12vDC system and can be dimmed from a standard switch. Available in flood or spot configuration but in your application I would recommend the Flood option.
@DavidWilks2 жыл бұрын
@Lumitec I filled out the Pro Staff form and think there's an entire industry your product would have remarkable success within. If you follow my Channel, you'll note I travel all across the USA to marinas, dealers, and marine manufacturers to haul their boats. If I had @Lumitec lighting in my marine trailer and the peace-of-mind, my lighting would be functional in all conditions... as well as the safety, there simply is no competition in this sector.
@LumitecLighting2 жыл бұрын
Thank you for your interest in the Lumitec Pro Staff program. The application process usually take a few weeks to review.
@DavidWilks2 жыл бұрын
I totally have to install these lights on my Boat, Trailer and the truck!!!!
@manbeefcake2 жыл бұрын
Professional af!
@slyr12 жыл бұрын
Lumitec Javelin 600X LED Underwater Light is this complete with a device to change collars? Also when are you going to have a install video on what it costs to install one of these are they the most Lumens? or is there stronger more Powerful units ?
@LumitecLighting2 жыл бұрын
The Javelin underwater light contains our TTP technology built-in which allows for color selection without the need for an external controller by simple off/on toggles of the power switch (see TTP operation link below). For more advanced color control you can add our Poco module, but not required. TTP Video: kzbin.info/www/bejne/ZmenoHVoist_qtU The Javelin and SeaaBlazeX2 our our highest lumen surface mount lights at 6000 lumens each. We also offer a through-hull SeaBlaze Typhhoon underwater light at 10,000 lumens for larger non-trailer boats. Installation video will be coming soon.
@sacredcreationz2 жыл бұрын
Worst product video I have ever seen. 80% had no lighting even being shown.
@LumitecLighting2 жыл бұрын
This is more of a new product line awareness video than a product information video. The link below provides some more technical information about the Javelin product than this video and when the product goes on sale in late December there will be more focused product videos available. kzbin.info/www/bejne/iZjRgIyFptx9qNU
@azoreandronefanatic2 жыл бұрын
My favourite lights! I’m converting a Ram Promaster into a campervan and I’ll be using nothing but Lumitec lighting throughout the van. That will include ceiling pot lights, perimeter lights, courtesy and step lights. I love the quality built and lumen output of these lights. The light is evenly distributed and above all many models are available in dual or WRGB colours and many are dimmable that tops it up for me on being the best lights on the market.
@owengerig3 жыл бұрын
not sure how to calculate bit size. (50% of major minor doesnt really make sense to me)
@D3nn1s Жыл бұрын
Basically the average. So if the threads are 5mm and the solid core of the screw is 4mm youd use 4.5mm
@mfawls96243 жыл бұрын
Didn't answer my question...but...gave me the necessary caution as far as simply drilling into fiberglass and chipping. I'm trying to attach a porch railing to a fiberglass (I think composite and fiberglass) column. Pulling off the railing chip the column and I've repaired that with Bondo but don't want further damage.
@iz74953 жыл бұрын
Hello. What is the life expectancy of these lights? I plan on buying two of them, the sea blaze Quattro.
@LumitecLighting3 жыл бұрын
All Lumitec products have a 3-year warranty. Actual life cycle will depend on use conditions and may vary, however our products have a strong reputation of well exceeding the warranty by many years.
@hepper73 жыл бұрын
I want to screw a 1/2 “ piece of plywood onto fiberglass. I was told to use a # 8 countersink bit first. What kind & size of screw should i use to secure it?
@johnpettit47573 жыл бұрын
Can this be raised and lowered with One hand or or are two hands required?
@LumitecLighting3 жыл бұрын
If the Anchor light is fastened to a surface it can be raised and lowered with one hand. The example in the video is sitting on a base plate that was not fastened to the table.
@louie44453 жыл бұрын
I want to add new chrome trim moldings to my cloth top on my Lincoln town car. What tools will I need exactly? That way when I go to Home Depot or Lowe's I can just have a list ready.
@LumitecLighting3 жыл бұрын
Luis, sorry but we have no experience with Lincoln town cars and therefore can not suggest which tools would be required for your project.
@C3c1l3 жыл бұрын
I need 2 but i live in Croatia, do you sell this im Europe?
@LumitecLighting3 жыл бұрын
Yes, We have a distributor in Croatia - MACA dba Elektrocentar & Nautic Shop. Ulica Knezad Trpimira 5, Trogir, 21220. maca-elektrocentar.com/ +385 98 49 7010
@ricardoanjos1693 жыл бұрын
Meu sonho um dia vai ser meu
@pitt56743 жыл бұрын
florida
@LumitecLighting3 жыл бұрын
Yes, Lumitec products are manufactured in Florida.
@bigg4903 жыл бұрын
idiot
@mikesobera52043 жыл бұрын
Great video and advice! Seeing all of these Lumitec videos have convinced me these are the best lights to purchase for my boat. Awesome customer resources to help DIY'ers.
@drainer4993 жыл бұрын
What is this song?
@LumitecLighting3 жыл бұрын
It's called "New Grounds" and it is from a stock music archive, don't recall which one.
@seamanvlogsqatar3 жыл бұрын
how i will install poco app in garmin mfd
@LumitecLighting3 жыл бұрын
Poco is compatible with the 8400 and 8600 systems and is configured into the OneHelm software at Garmin. If your system is compatible with OneHelm you will need to update the Garmin firmware to get the Poco app. If your system is not compatible then you can still access the Poco module via the mobile app thought a connected smartphone.