How sharp of a blade are you using. Everything I tried laughed at cutting, Nothing as nice as yours.
@KnifeKits3 сағат бұрын
We use a fresh razor knife and recently sharpened scissors. They work like a charm and will give you super clean cut edges.
@alexshaw28238 күн бұрын
What kind of foam is that inside your taco press
@KnifeKits7 күн бұрын
Hi Alex. We use "Maxx" form for the base layer and "Xtreme" form for the contact layer. You can see them here: www.holstersmith.com/vcom/molding-presses-foam-molding-foams-c-548_524_810.html
@georgemoomaw943710 күн бұрын
Drop the loud obnoxious background noise. Along with what I learned came a pounding headache.
@georgemoomaw943722 күн бұрын
Perhaps a better title might be “How to Use a Belt Sander? I thought that useless segment would never come to a conclusion.
@anwatsadat6786Ай бұрын
Can you explain why the thickness is important? When would I want a thicker piece of foam and what would dictatate using a thinner foam? Thanks..
@KnifeKitsАй бұрын
Hi Anwat. The thicker the item is, the thicker the foam needs to be. For example, if a handgun is 1.5 inches thick at it's widest point, the foam on both sides of the press should be at least 1 inch thick (2 inches total) to allow them to completely wrap around the gun's contours on both sides when being pressed. This allows them to push the heated thermoform plastic into the various recesses to fully cover (form around) the item. Let us know if you need more help!
@nak2048Ай бұрын
Do they Ship to Canada?
@KnifeKitsАй бұрын
Yes, we can ship it. 🙂
@FrancoisDeWet-jz9fdАй бұрын
Good👍
@FrancoisDeWet-jz9fdАй бұрын
Good👍
@FrancoisDeWet-jz9fdАй бұрын
Good👍
@FrancoisDeWet-jz9fdАй бұрын
Good 👍
@Edwardemeus2 ай бұрын
What foam did you use?
@KnifeKits2 ай бұрын
We used 1" Xtreme Form foam on the outer and 1" Maxx form for the inner. Here's a link. Let us know if you need more help. www.holstersmith.com/vcom/molding-presses-foam-molding-foams-c-548_524_810.html
@seraph...447326 күн бұрын
Heres a tip most channels dont mention. If your gun came with a plastic carrying case, sometimes they have foam in them, just flip the foam over to the flat side and use the carrying case as the press. Makes it very easy. Sometimes the case isnt big enough, but usually it is.
@KnifeKits25 күн бұрын
Be careful trying something like this. Most carrying case foam will melt to the heated Kydex. Also, a thin plastic carrying case will deflect too much when you press it. If you're going to make a homemade press, use a minimum of 1/2 inch plywood to eliminate deflection. We use 3/4 inch on our wooden taco press. Read all about foams and presses here: www.holstersmith.com/vcom/tools-molding-presses-foam-c-548_524.html
@seraph...447325 күн бұрын
@@KnifeKits Definitely true. Ive made about 6 holsters with carrying cases, another dozen with a nicer press. Never had any carrying case foam melt on me, but theres a massive amount of variance in that foam, and the carrying cases certainly do flex.
@ClantonCombatives2 ай бұрын
What urethane resin is it? I have some weird/rare allergies.
@KnifeKits2 ай бұрын
Hi Matt. It's a proprietary formula.
@ClantonCombatives2 ай бұрын
@@KnifeKitsunderstandable. Thank you.
@ClantonCombatives2 ай бұрын
@@KnifeKits the stuff I use for my trainers is terrible for holster making. Trying to offer some minimalist holsters along with them. I’ll support you guys ordering these as durable as they seem. I’ll wear gloves to be safe.
@benfernandez6912 ай бұрын
Man that was rough
@plwill40cal202 ай бұрын
Very nice holster nicely laid out, cut, drilled, riveted and belt sanded, sanded, sanded and did I say sanded. I've seen paint dry quicker than that. Edit out about 6 or 7 min. Of belt sander and you have a WINNER!!!!!
@authentic42253 ай бұрын
Where buy the vaccum press lol
@trevorbeckett32483 ай бұрын
How about rubber gloves 😅😅😅
@KnifeKits3 ай бұрын
:-)
@sportsandcomedywithconnorc9363 ай бұрын
Why doesn’t the kit come with the template? Is it just assumed we’d scratch our guns?
@KnifeKits3 ай бұрын
You won't scratch your gun if you take your time with the prep work and molding. If you're only making a single holster, a live weapon is perfectly fine to use. If you're doing several holsters for that model, we recommend a molding prop just to be safe.
@Mr_Redact3d3 ай бұрын
Can’t thank you enough for this video!
@paulbrooks35513 ай бұрын
I am looking to get into making my own holsters. Can you do a video on the retention jigs i see them in alot of videos but no videos on just those jigs
@KnifeKits3 ай бұрын
Hi Paul. Thank you for the suggestion. We get questions on creating retention all of the time. I'll add the video topic to our list. If you need any help using one right now, feel free to call us and we'll walk you through over the phone.
@mhager0173 ай бұрын
Thanks for the video. I just made my first kydex sheath and it turned out pretty nice overall. The one thing I had some difficulty with was getting the right retention. If you could make a video demonstrating where the retention comes from on a knife and how to adjust it, that would be awesome! Thanks for the great products and content.
@KnifeKits3 ай бұрын
That's a good idea. It's not as straight forward as it seems. I've added "knife sheath retention" to our future video list. That's a topic that we should definitely cover. Thank you!
@TommyCoKnives3 ай бұрын
What size eyelets are needed to fit the 1/4” post?
@KnifeKits3 ай бұрын
Hi Tom. Use the #8 (1/4) inch diameter eyelets for those. If you're working with 0.080, use the #8-8 length, and with 0.093 use #8-9 length, etc.
@georgehewitt35163 ай бұрын
Can you take in off and will it mess up your holster?
@KnifeKits3 ай бұрын
It can be removed, but it may leave adhesive residue behind. Once you put it on the holster, and it has some time for the adhesive to semi-cure, it's pretty stuck. If you're going to remove it, do it sooner rather than later.
@DisgruntledVet3 ай бұрын
I haven't even watched two minutes of the video and it is already more informative than the SDI video I am going off of. That is why I'm searching the web for better videos. I'm so stressed out over this class when it should be fun.
@Icephamtom3 ай бұрын
If I sent you my holster could you wrap it for me ?
@robg84334 ай бұрын
Recently ordered a 12x12 mc. Will let you know how it goes in application to my holsters and gear..👍🏼🎯👈🏽
@itsjake19904 ай бұрын
What size post and screw are you using?
@KnifeKits4 ай бұрын
It's a .250 post (www.holstersmith.com/vcom/slotted-post-steel-black-oxide-finish-pack-p-3722.htmland a .4375 screw (www.holstersmith.com/vcom/phillips-oval-head-4375-300-1ea-p-6704.html) Let us know if you need more help!
@josemariasilveirazacarias71544 ай бұрын
Os pinos poderiam ficar mais perto do molde. No video me parece que esta a 2,5 cm e com 1cm e ate 6mm ja é suficiente. Obrigado pelo video
@noshillgunreviews4 ай бұрын
Question, what does supercam nightstalker look like? It appears to have a slight blue/grey coloring to it.
@KnifeKits4 ай бұрын
It's mostly medium gray tones to deep black in color mix.
@TheCaptnHammer4 ай бұрын
Nice Stache. I highly approve good sir. Making my first holster today! Full kydex followed by hybrid if it goes well. I have only done full leather thus far so this will be exciting!
@seadevil265 ай бұрын
Great Vid!! very detailed
@knightshousegames5 ай бұрын
6:29 This is good advice in situations outside of sheath making as well
@soundsnags20015 ай бұрын
What's that white junk your drill press is smashing?
@KnifeKits5 ай бұрын
It's cutting board material. You can also use a block of wood to backstop the assembly.
@GTK33925 ай бұрын
Can you show how the washers and screws go? I’m new to all this.
@KnifeKits5 ай бұрын
They mount with 1/4 inch holes through your KYDEX holster or sheath, similar to the FOMI clip on this video. kzbin.info/www/bejne/n6nVZn2rrbqke6Msi=luUtM4MudRoFniHk If you still have questions about installing them after watching the video above, reach out to us at 877-255-6433 and ask for Robbie. He can walk you through it on the phone.
@MD-1736 ай бұрын
can you provide me with a 12"x12 500D Cordura with poly in Ranger Green? Your site only offers 6'x12"
@KnifeKits6 ай бұрын
It's half-way down this page. www.holstersmith.com/vcom/edc-wrap-sheet-material-c-546_1057_1061.html Let us know if you need more help!
@MD-1736 ай бұрын
@@KnifeKits Thank you. Just created acct and purchased. Also Subbed. Question: I bought a Safariland 6354RDS in what they call "Ranger Green" which is actually 100% without question OD Green. So my intent is to disassemble the holster wrestle off their cordura wrap and install yours. Any tip on the removal? I wish you were in south Florida, I'd have you do it. Thanks again.
@KnifeKits6 ай бұрын
About the only way I know is with a heat gun. However, with medium-high heat, you risk deforming the holster. I wouldn't add much more than low heat to soften the adhesive. Thank you for your business. Welcome to the addiction! Alex 🙂
@MD-1736 ай бұрын
I think a heat gun on any setting is not good. @@KnifeKits
@johnbrouillette86336 ай бұрын
You didn't have a white chalk pencil lol jk
@adrianlouviere76506 ай бұрын
Very nice instruction. Thanks for sharing your wisdom.
@JSmitty333496 ай бұрын
Will it make that click sound when the gun goes into the holster? I'm not sure what in the process causes the holster to have that. I ordered one that doesnt do that but most of the ones I've ordered do.
@KnifeKits6 ай бұрын
That "click" sound is something that we all love. In order to get it, you have to create "retention points" in the holster shell. As an example of a retention point, when you look at the video title image on this video, you'll see an indention within the trigger guard area of the holster. This is generally found on both sides of this type of holster. It is created there by design (by the foam pressing the thermoform material into the cavity caused by the trigger guard), and this creates one of the major retention points on all handgun holsters. The kit comes with adjustable retention assemblies that allow you to tighten (or loosen) the "pinch" along the holster seam to create additional friction on the handgun. Don't worry, once you make your first one, it'll all make sense. If you follow the video steps, you can't go wrong. Let us know if you need more help!!!😃
@Treasuremonk6 ай бұрын
This is like watching one of those hostage videos where the kidnappers make the hostage say things under duress!😂
@lostagain29926 ай бұрын
How in the world do you do iwb horizontally?
@KnifeKits6 ай бұрын
Ha ha, good question... It should be pointed out that we're using the IWB straps to create an OWB horizontal carry setup. Thank you for pointing that out.
@tripletholsters3956 ай бұрын
Very nice. Just bought both of the ASM handcuff molds.
@bctruck6 ай бұрын
Is there a certain measurement between the grommets to match the holes in the tec lock?
@KnifeKits6 ай бұрын
Tek-lok's have a square mounting grid pattern. Each hole is 0.20 inches in diameter and 0.75 inches on center. As long as your eyelet hole spacing is a multiple of 0.75 inches you're good to go. This diagram shows it best: www.holstersmith.com/vcom/images/bld-tch_tek-lok_cad_1500.jpg Let us know if you need more help!
@bctruck6 ай бұрын
Was that a scotchbrite wheel that you used to smooth the edge of the sheath on?
@KnifeKits6 ай бұрын
They're not scotchbrite...exactly, but similar. 🙂Here's what you're looking for: www.knifekits.com/vcom/sandingpolishing-flap-wheels-c-1072_1004_1005.html
@bctruck6 ай бұрын
@@KnifeKits thanks. Ordered the 400 and 800 grit wheels.
@KnifeKits6 ай бұрын
Thank you for your business. That was a good choice of grits. One to remove stock and one to satin polish! 🙂Nice!
@rickluchtenburg81666 ай бұрын
I don't see the green ones on the site , just the bright orange. So do i assume it's just the color that was changed and not the material it's made with?
@KnifeKits6 ай бұрын
Yes, they only changed the color. The material they make them from is the same. They still had some green models left when the color change was made. They're on sale here: www.holstersmith.com/vcom/specials-c-916.html
@flyflung6 ай бұрын
What kind of pencil is that? Thanks for the video.
@mitchelperkins67236 ай бұрын
Looks like a soapstone marker
@flyflung6 ай бұрын
That is what I thought. Thanks
@jonathancamm6 ай бұрын
Howdy from Senoia. Thanks for the vid. Your vids and Iggy’s at FalTac are very informative. Hope to bend some soon.
@user-qf1en4wc5t6 ай бұрын
Do you have a video on how to make the press?
@KnifeKits6 ай бұрын
Here's everything we have: www.holstersmith.com/vcom/tools-molding-presses-foam-c-548_524.html
@jayrichey29266 ай бұрын
The taco press is genius!
@alpalmieri86446 ай бұрын
Great video need those straps for my knives.
@wiesejay6 ай бұрын
Wondered what the dowel that came with mine was for 😂
@geraldomoraes-fu5qo7 ай бұрын
What is the brand of the vacuum presser, or was made by you?