Excellent tutorial!

I have almost the same forklift I found changing it to propane was the best. There is a kit that is about 500.0

19:41 All cheap built trailers have 24 inch roof and luan wood to give strength,like you said they put screws in it,should use 3m double sided tape and 16 inch roof with no wood,and one piece rolled roof

I'm not interested in helping the Chinese buy their next aircraft carrier, so I work to not buy Chinese products when I have a choice. I bought the Aloris.

Brings back great memories getting that thing running! Nice to see it in its new home!

How do you size the 3 phase on switch at the beginning and the momentary on switch for the start capacitor? What amperage are they rated for? Can you put up part numbers?

need to do the same! thanks

Why not use a T or i section stock that way we won't need any drilling and tapping and a flat stock.

DIY cnc after 6 years when? 😄

You can use an oscillating micro-tool with a wood with embedded nail bit to remove the screws.

Wow, best instructions on phase converters I ever saw. Thank you.

Great work.

I just watched your Linear Slide Bearing video from years ago. I was wondering, do you think the linear rail provides a smooth enough slide for camera work? Or would V slot plate and track be better? I really just need to construct a vertical track camera rig for ascending and descending shots. And I don't know the first thing about cnc.

Good job

can i use this setup on mig welder 350?

Good job exactly how its done

Would this work for 3 phase transformer charger?

Up north where I live they get economy trailers with fiberboard in them which is heavier and worse than plywood even! They are charging $10,000 for the size trailer and it is a piece of junk. I personally ordered my trailer from Georgia and spent $6,000 and got upgraded 16 on Center framing everywhere extra height and poly core siding for 40% less money. The trailer Market is very deceptive in you have to watch out it is a very tricky Market to navigate. Great video! There aren't many videos on KZbin showing the build qualities of these trailers in the differences between the manufacturers.

Hat post wall studs and Z post tops are the cheapest and worst quality parts. If they use those I would stay away from them. The tube are much stronger and better quality.

Polycore is the new way to side a trailer. 4 times thicker siding. All the Georgia companies in 2024 all have dual electric brakes on their axles. I have looked at the cheapest economy trailers and cannot find any that do not have dual electric brakes anymore. You also need to look at frame cross members because some of the more expensive trailers have cross members every 24 in on Center and the cheaper ones are actually 16 on Center which is stronger and a better build quality. You really have to do a lot of research nowadays because you're overpaying for less quality with some Brands and you are getting a much better deal on others paying much less. The bottom line is you really have to do your due diligence and learn what you are purchasing when it comes to trailers!

Just get in touch with the company and replace the offset bearing for an on-size bearing.

Make sure to put all the start capacitors in when you do that portion of the build. I saw working up with the run caps and thought I was supposed to do the same for starts. The reduced amount caused a catastrophic failure of the caps.

Is the motor an induction motor?

I have a LeBlonde Regal lathe too. How wonderful to see such similarity with your setup. I just purchased an Aloris set. I was using the original tool holders that came with the lathe for some years and found them to be difficult to work with at 60-70 years old. Anyway, I did not have to mill my own T-nut. I purchased during their August 15% off sale. I had nothing to loctite. All the set screws were SAE and properly fit my hex wrenches right out of the box. I will never regret my purchase, having looked at how the Chinese support this or that on the international stage. Yes, the Aloris was much more expensive. Freedom, is however, not free.

Doing the same thing on mine right now, this will help me, thanks!

So, did it work? Sorry for the language, I'm Brazilian and I really liked your idea and I developed an identical one, but I haven't tested it yet.

Great vid. How do the rails attach to the aluminium backing plate? Are they screwed in?

No sealant at the screw holes? Water will find its way in there.

I know it is a 2017 video_clip but the link to the "Document I followed: www.practicalmachinist.com/FitchWConverter.pdf "doesn't work anymore. Do you have a link for the Document I "that does work. Ty

Great video, very understandable, thanks for making it

Been looking into making one of these for a While and this is the first video that makes it make sense. Awesome video!

Thank you for the short, and on point, video. Much appreciated. I have a quick question. I am making a system where I will lift an empty bead to get it out of the way. Do you think it would be possible to put two rails in series, to increase the length, and have the wagon cross to the next rail? Not much precision in my project, so I guess that helps.

I have a 2320 mini tractor and i took my tank out clean it and it was fine for awhile then i had the same thing happen again so now i just shoot some compressed air through the vent tube and its fine.for a bit

That’s a 32k trailer new in Canada

Does it matter if you use more capacitance that is needed? I slapped 240 uf(all I had laying around) on my first legs and it balanced within 1v.

Very smart idea. Im thinking to do the same on my cnc. Does it overheat after eg 1hour running cnc spindle?

Perfect 👍

I tried to turn over a 10 hp 3 phase motor with single and a pull-start. It would hum, not attempting to speed up, until blowing the 10 amp breaker. What do you think is causing this?

Thanks, I'll check out the rest of your channel and see what else you got that will be helpful for my build

Nice work and great vid. Great the straightforward way you 'simplified' the process. THX!

Thank you for the video DO you think that work on a setup that like the cross-cut set up the cross arm ties on one side

Thanks for explaining the adjustments, mine are loose. Tempted to add another two grubscrews to spread te load.

Can i use a NEMA 42 to rotate a screw feeder in food dispensing with an 18mm diameter screw shaft? My load is 25kgs.

Could you run a 3 phase welder using this rotary phase changer maybe?

How did you size your conductors, devices and fuses

Its not a ground wire , its s bonding conductor

Solinoid - contractor - motor starter Solinoid has a magnetic coil when energized performs a mechanical task ( door latch, valves, bell, ...etc) Contractor (relay) has a magnetic coil when energized performs a mechanical task of closing electrical contacts( switch or switches) Lights, control circuits, motors( if HP rated) ...etc. Motor starter has a magnetic coil when energized performs a mechanical task to close electrical contacts and also has an intrigal motor protective device incorporated with it. Some are resettable if tripped and have interlocking contacts of their own to interrupt the starting circuit

It's a motor rated relay. A motor starter contains some sort of additional motor protective device

you know what might be a sweet project to do in aluminum, some end caps for that square tubing. I think that thing is sweet though, good job for sure.

The bar lock is the upgrade from the RV latch and an extra charge for all of the trailers that I've shopped. As for your awning and porch light ... you will exceed the legal width limit for all interstates and a lot of state roads too. I doubt they'll give you too a lot of crap for it but they can.