6 жыл бұрын
8 жыл бұрын
8 жыл бұрын
8 жыл бұрын
8 жыл бұрын
8 жыл бұрын
Пікірлер
@ytboombox Жыл бұрын
very informative and instructional
@trentbever1370 2 жыл бұрын
Thanks William you saved me money and time in building mine. Yea it may take some effort in getting it in place but I think it is doable without the saw horse. My yak had to be a little narrower from scupper to scupper. I just took a little bit off maybe a quarter of an inch. I got a perfect fit though and glued most of it together. It fits perfect behind the seat an is low profile.
@mmunoz5875 3 жыл бұрын
No clue required?
@trentbever1370 2 жыл бұрын
Yea you are good to glue the vertical pvc as the threaded rod holds the bottom together.
@bryanstanislawski9439 3 жыл бұрын
It works!! I just built one.
@breauxp 3 жыл бұрын
Nice video! Do you still have the same setup? Any issues? Thanks
@ocuscaln6121 4 жыл бұрын
Awesome thanks 4 D upload i appreciate it much stay safe god bless👍
@arturomoreno4911 4 жыл бұрын
With a higher seat, do u see or feel that your stability effected? Great idea.. awesome
@Manuel_Z_Kayaks 4 жыл бұрын
Next video: How to repair broken scupper holes...That's going to put too much strain in the scupper holes especially if you are going over rough terrain and with a loaded kayak. I want to see it in use and want an update now that 2 years have passes in Dec 2020.
@bloodOntheStep Жыл бұрын
Exactly
@williamstorey5024 4 жыл бұрын
Did u glue altogether or just leave it as is?
@justwhoiam3726 4 жыл бұрын
May I suggest using schedule 80 pvc, thicker than the standard stuff, few bucks more, but I think it will end breaking issues.
@dougmarlow9466 4 жыл бұрын
$5.00 wheels, get real. Not likely pal.
@coreyw7131 4 жыл бұрын
4.99 harbor freight pal. Look it up
@brendaspencer698 4 жыл бұрын
It’s for real. I saw it myself at Harbor Freight this past week! 06/2020
@trentbever1370 2 жыл бұрын
I bought them today for that much, I really couldn't believe it but yep 5.00 a piece! At TSC they are upward of 20 a piece.
@dougmarlow9466 4 жыл бұрын
Tell u what, try mounting your kayak to the dolly outside WITHOUT your saw horses. U neglected to let viewers know how difficult it really is by yourself
@Manuel_Z_Kayaks 4 жыл бұрын
DO NOT RAISE YOUR SEAT IN KAYAKS LESS THAN 30" WIDE! I see the video is from 3 years ago. That kayak is too small for you and if it didn't happen (yet) a small wake from a boat hitting you from the side will roll you because you're way too high in that yak for your size... I was on a 13 ft yak and not that high and was rolled by a tiny wake that cost me over $1000 in equipment and electronics.
@steveokoren4059 4 жыл бұрын
Great idea save some money
@llEverydayCarnivorell 4 жыл бұрын
For the money you’re spending on your diy yak ruiner, you can spring for a neat strap down kayak cart😂
@williammorales7924 4 жыл бұрын
I spent less than $20 on my DIY Kayak cart
@coreyw7131 4 жыл бұрын
I did a Similar one. My cost was 18 dollars in total. Great video!!
@williammorales7924 4 жыл бұрын
I spent under $20 on the DIY the strap down is over 30 close to 40
@trentbever1370 2 жыл бұрын
Actually it doesn't cost as much and it stores perfectly in the same holes on top of the yak. I did have to file the scupper holes a little and shorten the horizontal pieces and it fits like a glove 😁
@1FishinAddict 5 жыл бұрын
Got one of these and the pvc will break eventually. Also removing the wheel after it’s in the water is a pain. Best way is buy a $30 kayak wheel from amazon or eBay, don’t waste your time building this.
@scoot6Tx 5 жыл бұрын
thanks for getting straight to the point with no 😒 intro 👍🏿
@sherndon1000 5 жыл бұрын
William, I am bought the same Yak Gear outriggers , how did mounting up front work out?
@williammorales7924 5 жыл бұрын
It worked fine as long as the water was nice and calm but when it was choppy didn't work as fine
@williammorales7924 5 жыл бұрын
It worked out okay as long as the water is calm it would probably be better if I had placed it in the back instead.
@sherndon1000 5 жыл бұрын
William Morales I mounted mine in the front and it’s working good so far. Thanks
@williammorales7924 5 жыл бұрын
Glad it worked for you
@williammorales7924 5 жыл бұрын
Just be careful on choppy water
@rm709 5 жыл бұрын
Do YOU KNOW though.....? Goodness that hurts the ears.
@Beykoz1 6 жыл бұрын
kayak carts and dolly's are $30-$35 on ebay, why mess with it!
@traviswhitworth6506 5 жыл бұрын
I guess if you didn't want to put the dolly back in your vehicle while you are kayaking? This type of dolly will fit in the kayak well when you get it on the water.
@INTRUDERVTWIN 5 жыл бұрын
The carts online suck thats why. U have to strap them to kayak and they dont work that great. Believe me i bought two different ones.
@colinhodsdon74 6 жыл бұрын
just what i need to compensate for the extra weight of my 50lb dog leaning out front and side to side
@williammorales7924 6 жыл бұрын
Thank you Bama
@phernandez4446 6 жыл бұрын
ok made one and my wheels barely roll given the lock nuts and washers you suggested. I am assuming that I have tightened them too tight. any suggestions other than making them looser.
@gtrevino50 5 жыл бұрын
I wouldn't use the lock washers because as you found out, you can't fully tighten the nuts to flatten the lock washers without making the axle too tight. The wheels aren't under a lot of stress, so I think plain washers are fine. If the nuts loosen up you can just tighten a bit each use. I'm actually going to try a nylon lock nut on the outside and see if that does the job of keeping everything in place.
@traviswhitworth6506 5 жыл бұрын
Ditch the lock washers. Some blue locktite for the nuts should keep them on but still allow you to remove them later if needed.
@laraujo417 5 жыл бұрын
Use nylon nuts inside acorn nuts outside no lock washers it should work just fine.
@RedfishInc 6 жыл бұрын
I keep hearing how the scupper holes are a potential spot for leaks. Is adding stress to these points a good idea?
@williammorales7924 6 жыл бұрын
Grizzled Old Dude theres always a possibility of wear and tear around the Scupper plug area that's why I chose the size PVC that I did it fits in their more snug there's no play in it. Therefore less possibility of wearing that area out.
@Manuel_Z_Kayaks 4 жыл бұрын
@@williammorales7924 It's not the hole that leaks...its where the hole meets the hull that cracks.. you might have used a 4 way cross to add support lengthwise with the yak to avoid straining the scuppers.
@lisajonas5646 6 жыл бұрын
Why not demonstrate how it rolls???
@williammorales7924 6 жыл бұрын
Safari Girl i will video the next time i take it out.
@chrisking3849 6 жыл бұрын
laying down in the water and lifting up the kayak to find the holes for the wheel unit seems a little not friendly or all that easy.
@nave747 6 жыл бұрын
tilt the kayak onto its side
@justinp2533 6 жыл бұрын
Hahaha Chris!
@coreyw7131 4 жыл бұрын
Maybe use common sense
@williammorales7924 6 жыл бұрын
You can find the bushing in the bolts and nuts section of the store if not have one the store clerks find it for you
@williammorales7924 6 жыл бұрын
Keep in mind the measurements are for the perception Pescador pilot 12 if you have a different kayak you might need to take a new measurement to cut the PVC pipes 2 actual size
@Manuel_Z_Kayaks 4 жыл бұрын
Haaa...Very few of the store clerks know anything...find an older clerk that runs the department.
@SargesAdventures 6 жыл бұрын
So if a person didnt want the dolly so tall (looks like there is more than enuf room) , could I make the 11.5" lengths shorter...Would it still work out? Great vid, thanks for sharing.
@williammorales7924 6 жыл бұрын
You should be able to cut the PVC pipe to the size that best fits your needs. I preferred to use the 11 inch for Rocky terrain and I have a 9 inch for flat Terrain.
@williammorales7924 6 жыл бұрын
You should be able to cut the PVC pipe to the size that best fits your needs. I preferred to use the 11 inch for Rocky terrain and I have a 9 inch for flat Terrain.
@waynekeck5792 6 жыл бұрын
Nice Job!!
@jwrhynejr.6689 6 жыл бұрын
Good info! Thanks!
@arthurmcmahon3220 6 жыл бұрын
Good job man it worked like a charm than you
@bluewidow1734 6 жыл бұрын
Your a smart dude
@jamesf314 7 жыл бұрын
Please avoid the lawnmower next time. Otherwise great vid
@Unplugged704 7 жыл бұрын
I'm looking to build something like for my kayak.. with a $50 budget. I checked out the price for what you purchased and wow.. that's expensive.
@ozer1980 7 жыл бұрын
I built one with forearm crutches, boat bumpers, some pvc and flag pole holders. Mine cost around 50 bucks.
@williammorales7924 6 жыл бұрын
@@ozer1980 you can try to use some empty orange fanta soda pop 2lt bottles fill it with spray foam and use pvc to make your own under $50.
@duanediablo5607 7 жыл бұрын
You want 2 go on big water Brak yer Bank on a better yak.😎
@jesseo3974 8 жыл бұрын
If you are thinking of staying inside the bays......the last item I recommend for your awesome set up....is an anchor trolley.....let me tell you they are awesome and well worth it.
@texascoastwandererkayakfis672 7 жыл бұрын
Wicked Bass I totally agree..I have the Pelican Icon 100X Angler and I installed the Yak Gear Deluxe anchor trolley system.. it is Awesome ..good luck !
@jesseo3974 8 жыл бұрын
hey bro...nice set up. where did you buy the ruler?
@williammorales7924 8 жыл бұрын
Wicked Bass84 I got it at Sports Tackle Unlimited
@jesseo3974 8 жыл бұрын
William Morales sounds good, im going to look it up.....just wanted to share something I did to my milkcrate.....the same way you used the bottom of another crate to make the lid, I used the top of the cut up crate and used about 4 inches of it for the bottom of my milk crate to keep my it off the bottom and more dry!
@williammorales7924 8 жыл бұрын
That sounds good. Also Academy or WalMart should also carry the ruler.
@searey29 8 жыл бұрын
Where did you get the upgraded seat? Thanks
@williammorales7924 8 жыл бұрын
I bought it at Academy. It's called a Stadium seat. Check my other videos for ideas on kayak fishing crate.
@williammorales7924 8 жыл бұрын
No problem