Great work Jack

Great video mate - how much do you charge for a job like this?

🪞💡

Would be nice to see some 45 degree angle cuts rather than using these trims

Matttteeee you can't leave a cut like that on the left. 😂

That’s Wickes in Lichfield. Keep up the good work mate

If anything goes wrong with the flexi you can't get it off because you have tiled over the nut. Apart from that nice tiling. 👍

Good job but you should close the seams between the cement board :D

If ypu had centred the window the cuts would ve good 👍 🤔 😳

The small cit in the corner on the left is not good enough it's too small always be mindful of how you set put the bathroom small cuts are poor always strive for the maximum amount of tile then ot looks like you know how to do it

How long did it take you to finish it?

Bro all screws 😢

Have you used those bucket savers? It’s a silicone lining for the buckets so when you mix up you can leave the last bit to go dry and it slips out so easy and saves you having to clean up the bucket at the end of the day. Just search bucket liners or bucket savers 👍

What blade do you recommend pal

What was so hard about what you did? Did I miss something?😮😮😮

Descubrió el aire😂

Who did that floor eblind, man 😂😂😂😅😅😅😅😅

Floors not level 😂😂😂😂😂😂

Good video. Do you have to remove skirting or tile up against it?

Did you chip off the adhesive as well or tile over it?

Back in the day I used to fully tile a big bathroom including the floor and grout up and be home for 3pm

Dude, do you know that the seams between the cement board should be closed, make waterproofing there, as well as where you twisted the screws

Craftsmanship is beautiful to watch. Your movements are purposeful and elegant. ❤

Clean job !!

Nicely done, interesting to see you leave a gap for the grout between the trim and tile edge. Do you leave the same mm gap between the trim and tile as the spaces between the tiles too? Keep it up!

Well done 👍 what's the quote for this job ?

без заусовки(спил под 45 градусов) уже не делаем

Look at you, Nice job!

nice.

nice bro jobs looks smart can you do a video on how to set out / where to start tiling in a whole room, basically a video showing how you know/where to put your setting out lines and working out where you will start tiling in various different room shapes. I finished my diploma a few years ago but wasn't able to go straight into tiling due to family reasons but now i want to get into it but feel that bit i have forgot slightly, as we only practised for 2 years in a square room please mate would help me loads as i can't find nothing detailed online about various room shapes and how to set up. thanks

Thanks Jack this was helpful for my first mosaic tile wall 👍🙌

43 years tiling here. Thanks for the tip on replacing the orange clips with the blue ones. My top tip is to get an X-Lock grinder and an X-Lock 14mm drill bit adapter for drilling holes in porcelain. With that, it's so easy to switch from grinding to drilling just by pulling the X-Lock release lever and snapping on the drill bit adapter. You'll need a couple of 6 inch adjustable spanners to change out the drill bits from the adapter because X-Lock grinders don't have spindle locks, but you won't need to carry a drill. Using a grinder to drill is much easier, they have more power than the average drill, and you can drill without the need of a guide because the bit won't wander as you start drilling. I use the same setup to drill soft ceramic as well. Let me know if my description makes sense, and if it doesn't, I'll make a video.

🤝

You should always use a white adhesive if you using a light grout to guarantee no bleed through

Which adhesive are you using there?

Great video Jack, i like the in depth videos of a day in the life of a tiler, setting out, how to cut awkward shapes, fitting tile trims, around windows, etc. You can fast forward bits of just laying tiles and just detail bits that would be useful to a DIYer, then the vids wont run too long, keep em coming mate, great work.

Really enjoyed the video mate. I’m currently training to become a tiler/plasterer so any information on how you prepare your surfaces for tiling, screeding etc is really helpful

What happened to your cyclone?

Thoughts on Kerakoll H40 Gel Adhesive? Sick on adhesive skinning up too quickly.

Hi mate, just found your chanel, sorry dont know your name?, great video, i would have liked you to expand a bit on your other tiling tools which you have found best for your career so far, as in what is the best diamond blade for cutting porcelain tiles for your dewalt or makita?, I.E,budget and high end? Tile nippers, and must have tools. Im a handyman so its nice to learn off the pros, i hav'nt gone through your vids yet but it would be nice to see you doing some tiling, walls floors, awkward cuts, around windows, tile trims, around pipes etc. Got to take a look at those buihi clips, keep the vids coming, glad i found your chanel, kevin

Good for you mate for sharing your valuable experience... interested in the leveling system...you mention T-clip...any product name?

Bloddy heal

Well done mate very informative

When I started In 2009 clips weren’t even out and we had to do large format 6x6 and 6x3 rectified edge by feel. Now days you have apprentices who don’t have the ability to do a single bathroom without a laser level and clips and 1000 different tools.

Hi mate how did you get into tiling did you do an apprenticeship or fast track course? cheers

as a plumber who hates tiles, Great work mate! What disk are you using on the grinder?

Laser level?

I have the same grinding disc as you, how do I stop it chipping the glaze away from the edge of the cut tile?

Couldn't see what you are doing as you were in the way.

Very well put together vid fella, just a question i have , i have very rarely seen anyone in UK at least where i live to do corners at 45degree cuts (i mean cutting tiles at 45 in the corners and rather always use dirty aluminium corner piece or some sort of finish trim , in eastern Europe it would be absolutely not acceptable to do it just wondering