Joe's DIY Lab

Пікірлер

@rosenbergerstudios8865 5 сағат бұрын

Nvm…I can see that your kit came with actual holes to screw those braces into…mine came with just a slot/slider style so I can move those braces forward or backwards. Damn. I can see now that mine is an engineering fault.

@JoediyLab 3 сағат бұрын

Contact Vevor and ask them to send you the correct part.

@rosenbergerstudios8865 5 сағат бұрын

Hey man. Maybe you can help me. The 2 vertical braces that attach the steering wheel stand to the base frame are extremely loose - no matter how much I tighten them. Did you have problems with this also? I’m not sure how to fix it yet.

@Boogiewoogie1414 Күн бұрын

Little confused if you change the rotor you definitely have to remove the cable right? I guess working and changing's different but I mean we're just changing a rotor normally unless you try to bend it back which I'm not having a great time doing

@JoediyLab 15 сағат бұрын

Yes, as the wire harness goes through the hub of the rotor and comes out of the motor. You normally do not have to charge the rotor unless it becomes warped or scored. You might be able to bend it back, but it would be hard.

@Boogiewoogie1414 14 сағат бұрын

@JoediyLab yeah mine seems to be slightly bent It's been a a nightmare. But I changed brakes all together and that seems to have helped as long as you don't keep the tire too far back in terms of the chain bolt it works great. I was struggling for months with my brakes grinding on my rotor and it was just because my chain wasn't tight enough but it's a fine line to tighten it too much where the chain grinds or it's loose where the brakes grind

@JoediyLab 14 сағат бұрын

I doubt the rotor is heat treated, set the bike near a vice or anvil and see if you can flaten out the warpage.

@JoediyLab 14 сағат бұрын

I took my rotor off, routing the wires was hard but doable. Either buy a new rotor or see if you can straighten it out

@Boogiewoogie1414 13 сағат бұрын

@@JoediyLab I bought a new rotor but not sure if I want to try and get off the motor if I have it's difficult rn

@You.sure.about.that. 5 күн бұрын

You can also try and push out closer to the radius

@You.sure.about.that. 5 күн бұрын

Apply some heat to it and it should be a bit more malleable

@epcalderhead 7 күн бұрын

Thanks! Great content. This is the true value in KZbin.

@dynamitedmoney 9 күн бұрын

Thanks is such a fantastic video thank you! Do you know how to determine which cable goes to upper and lower on k9?

@JoediyLab 8 күн бұрын

There are numbers printed on the cables. The manual should indicate which cable is the upper and which cable is the lower. Haynes manual should indicate

@eloymarquez4783 10 күн бұрын

Thank you, you showed me how to use the ram. Have a nice day sir!

@eddiecruz6853 17 күн бұрын

Hi, nice video I couldn't find any videos for this but can I ask for you to make a video for the formula one mode? Because you can change it to that so I wanna see it before I make a purchase 😀

@JoediyLab 17 күн бұрын

Please let me know what game and what steering wheel do you have? Do you want F1 car mods or what, not sure what you mean?

@eddiecruz6853 16 күн бұрын

@JoediyLab The f1 game and I have the logitech g920 for Xbox. Can you change the racing cockpit to the formula 1 mode?

@JoediyLab 16 күн бұрын

No it is for GT style only. But check the Vevor web site they may have an F1 style cockpit

@davestewart9146 18 күн бұрын

What no heated and ventilation seat lol, just kidding, looks nice Joe 😁👍

@JoediyLab 18 күн бұрын

Dave, it is the cheap model. 🙏 Thanks

@hansolsson3409 21 күн бұрын

Great video Joe, thank you! 👍👍

@ChrisLee66 22 күн бұрын

After doing this I don't care if I find that socket or not. Thank you.

@Richard-k5r3g 23 күн бұрын

I changed the chuck. My bearings are cheap, and no way to set runout. Not true for sure on this old model. Thanks for your help.

@JoediyLab 23 күн бұрын

@@Richard-k5r3g you might be able to find better bearings. But not sure if you can find any that you can set the runout, but I would check around and see

@Richard-k5r3g 24 күн бұрын

Will it take a #2 taper chuck?

@JoediyLab 24 күн бұрын

Harbor Freight changes which taper they use on newer models.. So it is best to remove the chuck and identify which taper you have

@marcosun4404 25 күн бұрын

12:42，The locking torque value needs to be converted through the formula, not directly tightened according to the manual value (90nm)

@manassehmontuy5277 Ай бұрын

You need to use a long impact socket for it to work correctly, you loses a lot of torque.with that socket that you are using, to light.

@Vigilant_Guardian Ай бұрын

chipper is on the 3 inch feed side / the shredder is on the hopper side.

@nutindoin2 Ай бұрын

You should invest in some power tools, ie power rachet, or power drill driver for a faster disassemly/assembly, !!!!!

@JoediyLab Ай бұрын

Thanks, on the list of things to buy 🙂

@jimb3900 Ай бұрын

Besides the runout on the original chuck, when I rotate the handle(s) to make the drill assembly go down, if you grab the chuck there is a lot of play there as well. The chuck mounts into the assembly that goes up and down, that assembly has way more play. How to fix that?

@JoediyLab Ай бұрын

You may or may not be able to fix that. Take a look at the drill spindle, there may be bushings you can adjust or replace. Remember it is a cheap drill press not a milling machine.

@ColHogan-zg2pc Ай бұрын

Ho-ly crap, I was looking to use this exact same electric blanket to do the exact same thing. My yeast will thank you in these cold winter months!!

@hansolsson3409 Ай бұрын

Thank you Joe!

@markbro4427 Ай бұрын

Maybe ok for lighter springs/smaller cars, I've seen some Amazon reviews of them actually bending under load BUT the Sealey RE231(this is a copy of that) is far heavier built, been using one for years but its 3 times the price....For safety sake i'd go for the Sealey if going to do alot of work....Some springs require to be almost fully compressed, not sure I'd trust this tbh... spring injuries can be horrific.

@JoediyLab Ай бұрын

It did my Vw and was very easy. The sliding rail and spring caps are very beefy. I do not see a problem.

@markbro4427 Ай бұрын

@@JoediyLabtry a BMW 1 series front 😂 Your spring barely needed compressed to get the top mount on....As I said some springs need almost fully compressed, you'll even find you'll need to take the compressor apart to release the spring and shock assembly as they can trap themselves whey released. It varies greatly from car to car. Some are easy some not so easy especially springs with a taper.

@Deejaycambo Ай бұрын

Do u have to solder ? I don't have access to one 😮

@JoediyLab Ай бұрын

You can use insulated crimp on connectors, but the best way is to solder. You can get a Harbor Freight solder iron for cheap. See my video on using the Harbor Freight soldering iron

@Deejaycambo Ай бұрын

@JoediyLab I got the same battery as u but have no way to solder can't I just use.the charger with the barrel on it and unattach the original charger wire ?

@JoediyLab Ай бұрын

Battery has a different amp hour rating, you have to charge the batteries separately

@Deejaycambo Ай бұрын

@JoediyLab what do u mean? I'm asking if I can remove the original charging wire on the jetson and use the wire from the new battery I bought the same battery u bought but 10 ah

@JoediyLab Ай бұрын

Are you using the original battery and a new battery, if so you have to charge each battery separately. If you are replacing the original battery then yes you can wire use the existing charge port. But use the new battery charger you got with the new battery.

@mastermasteres Ай бұрын

Hello, I am having irregular idle and engine seems rough, I changed the PCV valve that worked for around 200kms got a new valve again but now it lasted 350-400kms, did this ever happen to you ? gti mk5

@JoediyLab Ай бұрын

Yes, when I changed the PCV valve. You have a vacuum leak around the front PCV plate, that faces towards the front of the car. The rubber gasket is leaking. I used the original screws from VW, the screws that came with the new PCV valve, were not flat enough.

@mastermasteres Ай бұрын

@@JoediyLab Ok will have a look again, but I also used the same VW screws, what would you do ? Would you clean the throttle body anyways ?

@mastermasteres Ай бұрын

@@JoediyLab Thank you for responding too!

@JoediyLab Ай бұрын

If this works and you can please make a small donation to support my channel, thanks 🙏

@JoediyLab Ай бұрын

If you have not cleaned them and have higher mileage, I would clean the throttle body. I used a smoke leak detector to find my leak.

@bobbelsekwol Ай бұрын

Sharpen up the shredder blades. Run it flat out. I've never had issues with mine like that.

@andyreyno9312 Ай бұрын

1:00 is that the stator relocated to the outside? Thats actually really smart

@JoediyLab Ай бұрын

It is the stock configuration.

@grampadad Ай бұрын

Working perfectly now after attaching the probe to the heating pad! Thanks 4 your help. I'll sleep much warmer tonight lol

@matter-under-mind Ай бұрын

I need an adapter for my vacuum! That was so much better

@JoediyLab Ай бұрын

I got mine from Amazon, listed in the description

@j.26 2 ай бұрын

Lucky mine didn’t come with the adapters lol had to wait a month to use it I couldn’t find stores near me with adapters 🤣

@JoediyLab 2 ай бұрын

Funny, I have all three, 3/8, 1/2 and 3/4. Only the 3/4 did not have adapters. Hope you got it sorted out

@ricrobinson9965 2 ай бұрын

I don't have to clean up and reuse. Get a dedicated grease gun. But then,, that's progress...

@JoediyLab 2 ай бұрын

I do not clean and repack many wheel bearings, So it is not needed for me to keep a dedicated grease gun. My be progress for you but not for me.

@fauxque5057 2 ай бұрын

I haven't hand packed a bearing in decades. I use a tool by KB Tools. It's a polycarbonate tub you load with grease. Take off the top. Drop the bearing on the shaft. Put the top back on and push down. Perfectly packed bearing. No mess. Nothing to clean up afterwards. I store it in a 1 gallon ziplock bag so it doesn't attract dirt.

@JoediyLab 2 ай бұрын

Sounds like a good tool, thanks for the feedback ☺️

@Johnny2Bag 2 ай бұрын

what does a 9 volt battery and a butthole have in common? punchline * You know it's wrong, But your tongue ends up there anyway...👅 dad joke 😅

@Johnny2Bag 2 ай бұрын

👍

@amairanihuidobro 2 ай бұрын

is the oil suppose to leak? when i open the fuel valve that is whats happening to me

@JoediyLab 2 ай бұрын

Where is the oil leaking from? Is it oil or gas?

@amairanihuidobro 2 ай бұрын

@ its the gas

@JoediyLab 2 ай бұрын

If when you turn on the gas and the gas starts leaking, you have a stuck float in the carburetor. If you are up to it , you can fix it yourself. If not you will have to take the chipper to a small engine repair shop. If you want to try. Go to KZbin "Taryl Fixes All" He owens a small engine repair shop. Search his videos on leaky float. On his channel he plays a hilllbilly, but he is very smart and explains things in very simple terms. If you need help just ask.

@amairanihuidobro 2 ай бұрын

@@JoediyLab thank you

@WestCoastRoller 2 ай бұрын

It almost looks like you need to spring for the HF transmission jack with a load that size. Great job making what you have work!

@JoediyLab 2 ай бұрын

Thanks, yes that diff is massive.

@davestewart9146 2 ай бұрын

That diff is like a ford 9 inch on steroids, thanks Joe 👍😁

@JoediyLab 2 ай бұрын

Yes Dave it is massive, I cannot lift by hand, thanks 🙏

@WestCoastRoller 2 ай бұрын

Old school method for me. It works!

@JoediyLab 2 ай бұрын

Thanks for the feedback, me too

@davestewart9146 2 ай бұрын

Packing wheel bearings is a dying art unfortunately with the design of unit bearings, I prefer the first method myself, thanks Joe 👍😁

@JoediyLab 2 ай бұрын

Thanks Dave, me too ☺️

@KelikakuCoutin 2 ай бұрын

Looks like the pump is messy and wasteful, as well as just as much work as the manual method, which doesn't require any clean up. By the time you set up the pump and dismantle it, then clean up all that extra grease, you'd have already done the second bearing. The only way that pump method would be worthwhile is if you have to do a good number of bearings. For example if you had ten or twenty bearings to do, the setup and cleanup would be worth the extra time. For only a set of two or four bearings, it may not be worthwhile. Thanks for the content. Keep up the good work. בס'ד

@JoediyLab 2 ай бұрын

Thanks, great comparisons

@JoediyLab 2 ай бұрын

Thanks, great comparisons

@VivekSharma-gv3hi 2 ай бұрын

Which ic

@JoediyLab 2 ай бұрын

Remove the whole board. You are not going to be able to modify the chip or the code on the chip very easily.

@smsadirul11 2 ай бұрын

Hi Sir, How are you? Are you looking for a professional KZbin Thumbnail designer? Let me know please Thanks.

@Kkkkkkkkkdkkjkekekwisi 2 ай бұрын

Cool

@WestCoastRoller 2 ай бұрын

Nice! I always thought that was a great idea utilizing an existing floor jack rather than shelling out hundreds for something specialized.

@JoediyLab 2 ай бұрын

Thanks for the feedback 😃

@davestewart9146 2 ай бұрын

These are the types of fixes I like, nicely done Joe 👍😁

@JoediyLab 2 ай бұрын

Thanks 🙏 Dave

@davestewart9146 2 ай бұрын

I have an older HF trans adapter for my floor jack, it was a demo and missing some small hardware, since they discontinued this model they gave me an awesome deal, great video Joe 👍😁

@JoediyLab 2 ай бұрын

Cool, thanks Dave, 🙂