EXCELLENT VIDEO, WELL DESCRBED.

well merçi

Thanks very much, I’ll be able to save a fortune.

I have two lights on "airbag fault" and "passenger airbad deactivated". Is there any point of doing your process in order to fix my problem?

Clear Airbag electricity tech safety video !

Great video

Or, just take the dash board apart (Really easy) and stick a bit of black insulator tape over the airbag light. It gets it through the MOT ! LOL

the old man tested things as you did and found no problems with connections between points, yet the airbag light remains lit :< i would have thought replacing basically everything with the appropriate resistor would switch off the airbag light, but it just stays lit. we're gonna grab a scan tool of some sort to hopefully shed some light on it, but i really don't understand what could be wrong. any ideas? i feel like i might have to go through the same process myself to make sure he copied you correctly

But we can live the resister in this place if we don't want to fix the problem yes?

Goodmorning. I bought two Sparco sports seats for the Peugeot 206 cc but they do not have side airbags. Under the car carpet there is a plug with three cables that must be connected to the original seat. Where can I find a side airbag emulator to connect to the switch under the carpet so that I can turn off the warning light on the dashboard? Could you please tell me what each color of the side airbag cable refers to? For example what is the 12+ cable. which is GND and which is the signal cable. Thanks. Best regards.

Me resulta muy interesante el vídeo porque tengo falla de que se prende la luz airbag y quiero ponerle una Resistencia. Lo único malo es que trato de entender pero como no entiendo el inglés se me hace casi imposible 😭

Hi John, I followed your test but have a problem. When inserting the resistors across the lower blue and brown connectors and then turned the ignition on, the light on the dashboard did not go out? So what could be the problem. The first part of the other connectors turned out the correct resistance.

your the man, i want to remove passenger seat in my nissan leaf and it has an airbag fitted in the seat. will it have two yellow plugs like yours, is it 2.2 or 3.3 ohm resister needed? what would i do about the sensor that tells the car someone is sitting on the seat?

Just fixed mine was the pin in the comm that clips in to brown clip

Hey, do u have an idea how i can byass with an resistor the esp/asr on the same car?

Hola hablas español ?

Hello John, I watched your video and it’s very helpful. I think I can use ur video in my car . I have airbag fault also. The airbag indicators stay on after I replaced a car radio .

Great video, thanks for making and sharing. My 3.3 ohm resistors are on order!

Thank you so much dear

thank you for the video, very informative

Thank you a lot mate! Tried this and turns out one of the cables had higher resistance ( at 2Ohms ) and was causing the airbag error. I simply starting shaking the small airbag cable assembly right behind the wheel and the resistance went back to normal, clearing the airbag error.

can the resistor be used to test other air bag components. how many watts is the resistor required to be.

Many thanks, I fixed my problem according your video

Peugeot 206 got some more life with this video, thanks!

left pretensioner squib open circuit 🤔

Don’t think you need high wattage resistors as the power running through them is tiny. Just cheap ebay ones will be fine

Hi mister John i really enjoy your video I just bought one 2.0 petrol 206 to run in circuit and every day car so I put sparco steering wheel and sparco buckets your video helps a lot so 3.3 resisters and the question I wanted to do how manny watts ? Our its doesn't matter? Please help

Thanks Sr, sorry but I crashed My P206, and the airbag system was activated, (thanks for god), now my car is ready to used but no have airbag system and this light is come on, I must make this in all system conector ?(steering wheel, passenger airbag connector, and seat belt).or only doing this in the steering wheel connector is sufficient?

No, never did. Sold the car for £300 so not worth deep investigation

Have you found out the problem?

Merci beaucoup pour cette astuce .

Merci beaucoup :-)

Ok thanks

I have a Peugeot 206 and have same problem with the airbag light always on but i was told its the passenger side air bag. Do u know how i would I fix that ?

well done sir thank you very much, my 205 has 156 thousand on it and this has been buggin' me for ages

Thanks for this video, I have had a Peugeot 206 for about 3 years now and it has failed the NCT here in Ireland because of this light, I think that a previous boy racer that owned the car may have replaced the original seats with bucket seats and I think put standard seats back in the car (without airbags) before selling it on and blocking the airbag light in the cluster display. This was pointed out to me by the tester. Have tried to fix it in the past but will use this method and test all.

Thank you. Your video has been very usefull for me

Hello there! great video! i installed a new steering wheel and got the airbag light, any suggestions?

I broke the green and yellow connector and the grey connector off, would you know where to buy these?

would a different car take different amounts of resistance? if so how do you find out how much resistance it needs?

Check you pushed both of the airbag connectors fully in before you pushed the yellow retainer home. The connectors should be firmly held in place if they are in properly. If not, the light will come on as the connection is not made

Don't know, his hearing was failing when this video was taken. Best instructor i've ever had though. Would suspect he's not flying any more

Is Toon still flying?

It's really nice to have a flight with Toon. Michael flew very well.

Do you have any other videos of the show?