Are you still liking your engraver? It’s been a couple months just a little curious.

What slicer do u use im struggling to dial in my prints

What is holding it in place?

you lost you audio...

What was the price from ebay?

So with this setup do you not need the ptfe tube?

Or just dremel the alignment holes 😅

what I really want to know is how the heck are you getting such good prints direct out of the box... ive set up three of these now for friends and they all have one problem or another...

I did not know they put a small bag of gummy bears for the mini. LOL. You get a regular size bag for the bigger models.

Wpuld you recommend this for scanning engine bays or bumpers?

After doing this my hotend no longer reaches temp. It won't go above 165. What can I do to fix this?

thank you

Need to use AESUB Blue ？

Hello! I’m using a ComMarker B4 20W engraver with Lightburn, and recently I encountered a connection error while engraving in 3D on brass. The issue occurred while engraving a 3D relief pattern with the following settings: speed 6000, frequency 45kHz, power 90%, line spacing 0.0254, image mode set to 3D Sliced, and 150 passes. After about 6 hours of engraving, a connection error occurred. I paused for a while and resumed engraving, but the previously engraved pattern disappeared. Then, after about 1 hour, the connection error happened again. Is there any solution to this problem? And is there a way to resume the engraving from where it stopped? I would greatly appreciate your help in finding a solution. If you need further assistance with refining the details or want to send this in a specific context, feel free to ask!

Got one for 400

The scanner cost more than my 3d printer with AMS and 10 1kg reels of filament 😮 But yeah the 3d scanning spray is expensive @ $30 😂

Nice! What size and type of stand/cart do you have your xTool on? Thanks!

What filament is that?

Thank you. This video was very helpful. I have a tent but it just takes up too much room. Just picked up this kit from Microcenter for $7.99. Marked down from $69.99. Sold!

very metal schat

90% these i do 5w diode laser. could jut cut clear and white acrylic. i cant LOL

I recently bought a a1 mini. It's a fast printer

by swapping the heat block you've unlocked the world of MK8 nozzles rather than the weird Neptune 4 length

Thanks for the fantastic tutorial! I followed it to a tee, minus replacing the thermistor since once I did, my printer no longer detected one being present. After swapping to an all metal hot end though, filament no longer properly feeds through the printer. The gears grab it and pull it maybe a few centimeters before the filament stops being pulled through, despite the gears still spinning. Anyone have any idea for a fix?

Hi, so I have a question because I kinda need help and haven’t found much online. I have this printer and love it. It is my first printer. I love it because I like to tinker and problem solve, but at times it is not the easiest to get setup especially when I was first starting out. The issue I encountered occurred after changing the nozzle. I am getting a minimum temperature error and the temperature control and the temperature sensor cable broke in the middle of the cable. I soldered a replacement cable and there is continuity when I tested it. The board pin out has continuity too. Do I need to replace the entire hot end board or just the cable?

$500 for a mini printer??? I bought 7 year old wanhao I3 duplicator for spare change and it works perfect

FYI the link to the 4 pack is incorrect... you need the CR10 type but the link goes to CR6. The CR6 are too long and in turn cause the extruder not to detect the print bed before it is too late. Nozzle, meet the print bed... Ask me how I know.... hoping nothing is broken.

Creality lizard?) I have it too. I like it really much!

Just bought one

Heya, question when reassembleing do you put a ptfe tube in the heatbrake like when before modding? It wasnt shown in the video at 1:46

How come there is no belt adjustment on the gantry?

I didn't realize that the thermister was PTFE lined... I switched to a metal screw in one for easier maintenance if they go bad but now I'm extra happy I did that!

Does it cut copper,and how thick? Can it cut 22 gauge roofing copper ?

Hey, once I get mine I'm coming back to you for walkthroughs. I need the file for the platform mod. Question: Is there software that comes with the 3D scanner or could I get it as a bundle with a 3D printer? Thank you in advance for your assistance.

My ender 3 has collected dust since getting my Mini, I've just got the upgrade bits to make it a Mini+ It might not get as much use as it used to now that I've got a Mk4.

The ghosting is real

What the fuck is it with you youtubes talking at lighting speed. Fucking annoying ..

How much is this machine Soo cool

Huh also you sound like huggbees

Whered you find the layout? Ive been meaning to make a 1k for myself too

Black & Decker were bought out years back by DeWalt. You could use the same batteries on either brand, thought that was funny. Not sure if it is still this way. It was about 25 yeas back.

the above link to the xTool D1 Pro 2-in-1 Kit: 455nm Blue Laser and 1064nm Infrared site sends you to a malicious website. Norton 360 stopped the site from loading malware immediately.

Can i use silk filaments

Great! I highly recommend this machine to anyone who is serious about laser cutting or engraving. It's an investment that will pay for itself in no time.

to be accurate, the scanner is not entirely stand-alone, as you must use it in connection with a PC or Mac to finish scans and export files

Would you mind sharing your settings for engraving PLA?

Mine just came yesterday

Did you replace the TPFE extrusion feeder back into it?

this was awesome...buuuuut, :) i did everything you did except changing the thermistor but now my nozzle does not heat up in time and my printer yells at me. any ideas?

I used the Aesub scanning spray and I'm not going to buy another can. It's 3x as expensive as I'm willing to pay.