Здравствуйте.Скажите .На сколько ключь под болты Цилиндра ?
@chrismuncey386129 күн бұрын
Could you share the port numbers on that bad boy ?
@jeremyarivettАй бұрын
its crazy how much those cylinders and the echo 8000,680,670 cylinders look almost the same
@maxwellgellersenАй бұрын
think a ported 261 would run a 25in bar??
@justinweaver8107Ай бұрын
The newer saw's cylinders are so different from the older saws😮
@kingsawsАй бұрын
Boy!!! SHORT BLOW DOWN
@gravewalker342 ай бұрын
50 cc monster.
@emanuelegarofano45142 ай бұрын
Great saw buddy!
@Casaperformancechainsaws2 ай бұрын
Interesting about the xtorq carb , thanks for the info 👍
@craigrogers31632 ай бұрын
Damn that sucker is screaming
@Witschor3 ай бұрын
The hose has to end in the right upper corner of Airbox. So nothing drips out while leaning it left or right
@IndianaDoug3 ай бұрын
Always great work👍🏻
@Super-Dave-Outdoors3 ай бұрын
Nice n clean!
@nikky3piece4523 ай бұрын
Nice job, she rips!!!
@nikky3piece4523 ай бұрын
Stihl 461 from Minnesota getting looked at yet? Will you make a video when you put it in wood please & thank you!
@JandSChainsaw3 ай бұрын
Looks just like a 362 jug didn't know they shared the same transfer design
@justinweaver81073 ай бұрын
Very clean❤
@jreif143 ай бұрын
What’s your lead time looking like?
@Houseworksaws3 ай бұрын
Right on…shop looks good
@treeguymatt3 ай бұрын
I was just thinking about how the shop looks good and then read your comment
@Leave_Nothing_Stock3 ай бұрын
I saw a video of yours on a 361 and sent me down this rabbit hole of wanting one for myself. Now ive got three unfinished in a box cuz i dont have the time for em. Never have got one to run well. Think Ill have to track one down to send your way. Just go right to the source!
@Houseworksaws3 ай бұрын
That’s totally me I’d have a cig going while building a saw on vid lol 😆.. if I’m in my natural habitat i just forget. Good to see you back bud
@Houseworksaws3 ай бұрын
Yeah buddy
@tonysdailygrind21623 ай бұрын
Good to see ya!
@tatepazaski54883 ай бұрын
Nice to see another one of your videos!
@TICKLE_MY_BEANZ4 ай бұрын
Do you want to try your hand at a t540xp mk3?
@BruceMyersLBZ4 ай бұрын
I LOVE mine, had mastermind do it up. Its is headed back down for coil upgrade tho, i have hogged rakers down and its still constantly on rev limiter w a full house 28" i swear it hardly loses any rpm in the cut even buried. Think it took 1st place in my heart even over my walkerized 346. Obviously they both have dedicated tasks, but at this point there is nothing like burying 28" into red oak and letting her pull! AWSOME underated saws!
@lumbearjack37224 ай бұрын
Ro you do a timing advance on these?
@coxsaws5 ай бұрын
Nice build 👌
@coxsaws5 ай бұрын
Very nice
@nikky3piece4525 ай бұрын
What kind of wood is that? White Oak??
@agpicker4815 ай бұрын
What kind of chai saw vise are you using here ?
@nikky3piece4525 ай бұрын
Sounds good! Throws chips!
@nikky3piece4525 ай бұрын
Which is better/faster, a 7 pin or 8 pin?
@nikky3piece4525 ай бұрын
That thing is snappy! Great job!
@nikky3piece4525 ай бұрын
Nice! Keep up the good work.!
@nikky3piece4525 ай бұрын
Yes sir that sounds nice!!
@nikky3piece4525 ай бұрын
You have mine in your possession! Make a video when you're done! Thanks Gary.
@jagcustomknives5 ай бұрын
Awesome! What lathe are you using on the four jaw here?
@MrMeerkat1476 ай бұрын
If i were to do a top end rebuild, would i have to mess with the timing at all? Or is it as simple as this tear down, install new piston, and then put back together?
@buxtonworksawsllc96456 ай бұрын
Just replace it all.. but make sure you figure out what caused it to happen or it will just happen again.
@johngraziano6596 ай бұрын
That 261 RIPS.
@davidwilliamson91626 ай бұрын
Weetus the music I think,er right idea but wrong way round,you need to retard the timing on a 2stroke n advance on a 4 stroke 👍 I actually did this on a Honda cb125te a long time ago in a galaxy far away 😂😎
@Skinnymoose6 ай бұрын
Wow
@josesecatero26376 ай бұрын
I have a stihl 661, its computerize, would u port that
@lassila37 ай бұрын
Good idea to have music in background🙄🙄
@petershea31317 ай бұрын
Very cool man. I’ll check out the site.
@petershea31317 ай бұрын
I’m telling ya no dogs necessary on this little saw
@johngraziano6597 ай бұрын
Gary, u have any new ones for sale that u ported?
@TheRealEricRose7 ай бұрын
What’s your blowdown numbers for most of your work saws?
@timberandtools7 ай бұрын
361 underrated for sure, of course this is ported but they’re not to bad in stock form ether!
@benboyer29048 ай бұрын
That little guy sounds pissed! Probably have to have you do that one too