easily the best tuning vids on youtube - thanks for everything you do Rabbid!

Hey bro What fuel is used for tuning?

sa ma laure bien

Hopefully you still check these videos! I noticed your oil pressure sensor had its pull up resistor enabled… don’t those usually have a 3 wire connection which don’t need a pull up? Also, are you familiar with using an existing oil pressure sensor/gauge combo like AEM? If it just has a 5v output, do you wire that directly to an AVI without a pull up resistor? I’m assuming there’s an offset since the gauge uses a chassis ground instead of a sensor ground?

4 years later and this is relevant, just set up my knock control basics,, and its ready to use! thanks boss!

How many hours of running inbetween rebuilds ? How much does the power drop from a fresh engine to worn out. Do they loose more than 2 hp ?

those noise spikes are gear clash when you take foot off gas

How much light have you left on the oil seals?

im currently building the same engine and we have a problem, when you fitted the rod bearings only 4 have holes and you have put 2 rods with all 4 holes and the rods on the left have no holes, im sure the ones with holes go in the caps, please help as im now stuck not knowing with way up to put them HELP!!!

How much whp does the stock one has? Auto or manual

Very informative video other than washer goes under water pump gear ,gear side crank seal should face outwards and water propeller seal should go flush with the case allowing weep hole to be clear,to remove old water seals there is a small hole where you can tap them out with a small diameter pic, case seals have 28 and 25 I/d numbers on them.

Thanks for taking the time to do this.

You have a video with NSP software starting from zero?

Hi. will you build me a 500 hp engine block?

pity the next episode never came!! After waching the whole series and realising how much work there is behind building an engine i almost don't want my engine to be rebuilt by anyone unless they can actually show and prove they can do it up to your standards!!! Thanks for this and hope i'll find someone capable of reaching such high standards!

How to sir map calendar

Thanks sir KZbin clear lesson

This is a fantastic video! Thank you!!

Just found your channel and these videos, absolutely outstanding work, thanks for sharing. It will help with my upcoming K20/24 build. Thank-you.

Hello, my manifold on my astra vxr keeps becoming loose (studs) have you ever experienced this ?

Where can I find the gasket and o-ring kits

can you just turn up with your kart

Watching this series again and again. Really appriciated the work which you done. Can i contact you somehow regarding tuning?

You need to try this again, ECU/fuel maps are available now with new turbo characteristics, superchargers are coming in next update!

Dear Richmond, Can i get please your e-mail adress to send you inquiry about tuning session. Dimi from.Serbia Just please send me the e-mail if you dont want to.provide here your contact adress. I tryed to contact you via your site but it seems that is not working anymore. Thank you very much Dimi

Monster

Where the timing vid bud

pretty decent video, having some trouble starting my r34 off a base map. unsure why but i have alot of things that arent standard anymore. Fly by wire, can lamba, trigger setup etc

Very interesting content 👍

I simulated my old Hilux in Automation and some of the creations I've made are stupid fun to drive in BeamNG

How do I scale 410cc injectors with nsp

Did you use an air temp sensor from link? You mention 1/4” but I only see 1/8” from link

learned more from watching this single video than my college has taught me in the 4 months ive been there

where can i find de manual of the rotax?

Hello this game seems really amazing where can i get it.

always remove main bearing when big end fails ,u will find bits off bearing behind it ,thrust washer goes on water pump shaft not idle gear ,good video

Any reason you're going after second order harmonics instead of first order?

Should I grind my piston ring to the right gap, and then balance the pistons? Seems like depending on how much each ring needs to be grinded to gap, it could alter the weight for that piston significantly.

question if the injector manual only gave me 8-14v do i just delete the 6v settings? thank you

Hi, can you help me with my vauxhall astra mk5 not make full power

Great guide, appreciate the info.

hey, how can I contact you?

Great video, it's given me a lot of confidence to work on my own engine when the time comes. Do you have any videos of tuning a rotax engine / carb etc. Am new to karting and my kart sounds like it running bit rough. Thanks

First, great chanel!! I'm building R33 GTR this wil get a full build engine with sequential gearbox. I really cant make my mind on what ecu, Haltech elite 2500 with terminated loom or Link G4X If you got to choose what would you go for? Regards Kenny

Excellent vid for me until the point i wanted to see which way up the blade should be on the power valve and you didn't show it

This is awesome mate, I am about to buy this ecu for my er34! I'm getting the flex fuel sensor too as I have a few extra mods and want to run e85

Is there a specific wideband kit that you are using for this ecu? I’m a little confused on which can plug and wideband I should use. I have a gtst so it might be a little different than the gtr. Thanks!

Legit just watched your videos about rabbid rom and how awesome the scaling is. Shame no one north wales yet are a dealer with you.

I like the way you spend the time to tune and explain it. I have a project on the go at the moment with a AH Astra 2007 in Australia, not many people tune these cars here (not popular like over there) I would like to know if i gave you the heads up on my car would you be able to help with a map so i can run it in before the dyno time ? regards Ken

Where does the vacuum into the engine go location please?