Thank you for making this video and thank you to the commenters. I had this exact problem and disconnecting the power thing for the valve that runs to the bleach dispenser worked! I was so disappointed after waiting impatiently for over a week for the new inlet valve thing and then the flood happened! 😱 We’re two weeks behind on laundry. Next I’ll be getting a secondary sediment filter for the washer
@workshopstudios439 күн бұрын
So glad you got it working again!! And thanks for pointing out how helpful other's experiences are in figuring out what to do. Many thanks to all of you who took the time to share!
@goat3413 күн бұрын
😂 Thanks Frosty. Great job. I built about six guitars from scratch and several parts guitars. I enjoyed your video. Thinking of doing an archtop next.
@workshopstudios4311 күн бұрын
Wow! I started making an arch top from scratch... Let's just say it's an ongoing project. Good luck with your build and thanks for the kind words!!! And the reference to my crazy song at the end of the video 😁
@theebikeguy385213 күн бұрын
I know this is a older video, but i love this design scooter, just picked one up, striped it down droped in a 1200w brushless hub motor, modify the fram for rear disc breaks, going to a 52v battery and 30a controller. Should do 35-42mph.
@workshopstudios4311 күн бұрын
Woah... I gotta see that. Please make a video and post it!!! Good luck with your "muscle scooter" and be safe 😁
@noomisoetaert514114 күн бұрын
❤❤❤❤❤❤
@workshopstudios4311 күн бұрын
Thanks for all the hearts 💕😀
@leemp33716 күн бұрын
Thank you
@workshopstudios4315 күн бұрын
You're welcome!!!
@elainemartinez717219 күн бұрын
Very helpful thank you!!
@workshopstudios4318 күн бұрын
Glad it was helpful! Thanks for watching and your kind words!!
@keithhayler654719 күн бұрын
I've now received my replacement and successfully fitted it with ease 😊
@jdjin29123 күн бұрын
I have a l110 model and my starter solenoid had only 1 connector pin on old one only.one I could fine is a double can't find the other wore to connect to other pin cause I have the correct one from battery to new starter solenoid and one from starter tried to figure out the wiring on this thing and I'm at a loss
@workshopstudios4320 күн бұрын
Not exactly sure what your dealing with but some thoughts. A solenoid is fairly simple; a positive and negative connection. One pin solenoid would imply that pin is the positive and the negative is achieved by the connection to the engine Two pins would be when the solenoid may not ground through the connection so the negative is supplied to one of the terminals. I hope that helps Good luck with your mower and thanks for watching and commenting!!
@keithhayler654726 күн бұрын
This video was very helpful. Although I now know that my actuator does need replacing this gave me the confidence to investigate it myself and get it working manually with the key until the replacement arrives. I will now be able replace it myself.
@workshopstudios4320 күн бұрын
So glad that the video helped!! Good luck with your trunk latch and thanks for your kind words!!
@dwhiteybАй бұрын
I just did one side of my chair and it was too tight. So when I cut the other side to do that side it was to far away. Then I went to KZbin and found your video. You explained the process and had good close up shots which were very helpful. Now I can go back and do it over and not get frustrated with it. Thank you!!
@workshopstudios43Ай бұрын
thanks for the kind words and great feedback!!! Hope it turned out well.
@AroundTheHouse-kp7rtАй бұрын
I am having issues taking the pulley off the gear box. Any hints?
@workshopstudios43Ай бұрын
You try loading it up with wd40 or a penetrating oil. I would be careful about using a torch (heating up the pully) because the housing is plastic (if i remember right) good luck with your mower repair!
@faithhouses6725Ай бұрын
Would have liked to have seen you scrub, shape, and dry the hat. The video went from you soaking to you wearing the hat.... it did not show the complete process.
@workshopstudios43Ай бұрын
My apologies!
@Peter-ic7vjАй бұрын
Where to buy?????
@Peter-ic7vjАй бұрын
Kit no.??????
@workshopstudios43Ай бұрын
I added several links in the video description. However, they don't always have them in stock. I have found searching for "hollow body electric guitar" will get to several choices as well. Look for the Bigsby style tremolo and maple laminate top. good luck with your guitar build
@jaimevalencia8094Ай бұрын
great video, so detailed. Do the drawers not close softly ? Mine get a bit of a pushback when fully closing or opening them.
@workshopstudios43Ай бұрын
They might be slightly out of alignment
@heyyouyayou7933Ай бұрын
drill a hole ,tap a screw thread, screw in long bolt. pull out stuck rod
@workshopstudios43Ай бұрын
Yep, I was in the middle of that when it broke free and started spinning. Made the job a little bit easier. Thanks for sharing and for watching!!!
@davidhahn5650Ай бұрын
I'm so glad I checked. I totally assumed that my kitchen microwave was mounted to the wall and not the overhead cabinet. I started removing the mounting wall screws from the cabinet, would have been fun to have the cabinet and a 25 lb microwave slam down onto my range!
@workshopstudios43Ай бұрын
So glad it worked out! Thanks for sharing your story!!
@margaretshaw4529Ай бұрын
Thank you so much as single mother of two I can’t afford a repair man or a new washer this has saved me… crazy same washer same problems!!
@workshopstudios43Ай бұрын
I'm glad I could help!!! And thanks for the kind words and sharing your story. I think this is the best of the internet and youtube experience; sharing and helping All the best with your washing machine. Ours is still going strong 🤠👍
@cheeseandrice87710 күн бұрын
I’m in the same boat mama!!! 💪
@melgiannino25132 ай бұрын
Hi, great job on the fix. I was wondering if you could send me a template of the movement part where the magnets go. I found one of these in a yard sale but that part was missing and the arm that attaches it to the motor. I fixed the motor but without the price with the magnets I’m shot. So if you can help me please let me know how we can proceed. Thanks in advance. Mel
@workshopstudios43Ай бұрын
Thanks for the kind words! I didn't save a copy of the plastic magnet holder. And I gave the one I fixed back to its family. Take a look at my other 2 videos on the skating pond ( parts 2 and 3). I replaced the plastic magnet holder in those. Hope that helps!!
@6806goats12 ай бұрын
China kit?
@workshopstudios43Ай бұрын
Yes it was
@kellynorco2 ай бұрын
I need these !
@workshopstudios43Ай бұрын
The chimes were from Costco
@lowellirish2 ай бұрын
What happened to checking intonation at the 11th fret? Making sure the bridge is sitting flush to / slight angle with the intrument top? Checking the tailpiece knob for security? Checking tuners and hardware for loose and/or missing pieces? 😉😳🤔
@workshopstudios432 ай бұрын
Yes to all! I never got around to making part 2 of that video. You put a great story board together for it. Thanks for sharing!!
@jaimedpcaus12 ай бұрын
So, measuring the pressure at the water heater is the same as measuring at various points inside the house? Thank you.
@workshopstudios432 ай бұрын
Great question! I'm not an expert, but from my research, the answer should be yes. But I'm sure there are situations where that may not be so. I read that the water heater is especially sensitive to higher pressure, so it seemed to be a good place to measure. What are your thoughts?
@jaimedpcaus12 ай бұрын
@workshopstudios43 My thoughts are that the water pressure is received from the either hot or cold water from the water heater (source) for the home. So, it would make sense that faucets would have the same pressure as the source. I had attempted to measure at the faucet but I didn't know how (still dont) and that's when I saw your video (pretty smart). 🤗👍👍
@dirk20992 ай бұрын
Any tips on how to remove the right bolt on the starter of a D155?
@workshopstudios432 ай бұрын
I wish I could help with that, but I haven't had to take the starter off ... yet Good luck with your repair!@
@Texasbluestunes2 ай бұрын
Black paint pen..
@workshopstudios432 ай бұрын
?
@leebrowwski2 ай бұрын
Didn't need to pay the stealership, Mr Bearhead!
@workshopstudios432 ай бұрын
You got that right!!
@jeffbarber84812 ай бұрын
Do you have the part number or package number for the part that bolts onto the mower?
@workshopstudios432 ай бұрын
I put a link to the part on Amazon in the description below the video Hope that helps Thanks for watching, and good luck with your repair!
@darlahughes47522 ай бұрын
We have a spinner that is about 8’ tall. A strong wind broke the pole into two pieces. Do you have any info about how to replace it? The top of the pole is pointed. We’ve had it welded before but it broke again.
@workshopstudios432 ай бұрын
you might be able slip the broken pole into a 8" piece of steel conduit thanks for the great question and sharing!
@thomasj97003 ай бұрын
I used the jack stands, this looks a bit easier. Are you able to use the kick sensor to open the rear hatch? Mine just beeps and doesn't open when I move my foot under the rear bumper.
@workshopstudios432 ай бұрын
We don't have a kick sensor on our car. I understand that can be a problem with some car/trailer hitch configurations. Good luck sorting that out! And thanks for watching and sharing!!
@sthengr3 ай бұрын
Great video, thanks!
@workshopstudios433 ай бұрын
Glad you liked it! Thanks for the kind words!!
@catzhaus28003 ай бұрын
EXCELLENT video!! So detailed and helpful!! Thank you so very much!!
@workshopstudios433 ай бұрын
You are so welcome! Thanks for the kind words!!
@steveho98843 ай бұрын
how do you make a blade guard and and a antic kick pawls and splitter for your tablesaw my friend has the same saw as you
@workshopstudios433 ай бұрын
My tablesaw came with those items, so I haven't had to make them. I have some specific jigs that have their own version of protection but that's not what you're friend needs. Thanks for watching and the great question !! Good luck with your tablesaw project 👍
@bobbamford52073 ай бұрын
There's no protector plate for the pulleys and belts under the mower? All the grass sticks rocks can get caught?
@workshopstudios433 ай бұрын
Yeah, maybe not the best design...
@bobbamford52073 ай бұрын
If he faced the mower into the light maybe we could see.
@workshopstudios433 ай бұрын
Sorry about that. Lighting is always a challenge . I have developed great respect for the folks in the film industry and how they get the lighting right
@SilentBob19323 ай бұрын
Nice, I was going to try mount to my Lawn Tractor, I’ll be doing this instead along with my Boats Deep Cycle Battery
@workshopstudios433 ай бұрын
Good luck with your sprayer setup!! Thanks for sharing 👍
@donnafenton72553 ай бұрын
Terrific video! Instructions did not come in the kit from Amazon. There are instructions on the site where these are sold but they are incredibly confusing. I have re-laced our chaise lounges now twice because it's that easy. Because of your video, I now understand what to do with the ends and where to double up on the seat part. Thank you.
@workshopstudios433 ай бұрын
Glad it was helpful! I have been helped by so many folks who have shared their experiences on KZbin. It's an honor to give back!! Thanks for watching and sharing your kind words!!
@TruthSeekerAi3 ай бұрын
i luv this it had me happy from start to end
@workshopstudios433 ай бұрын
So glad you liked it!! Thanks for watching and sharing 😊
@TopGunMan3 ай бұрын
There is another video on how to replace the broken shaft torque pin inside the transmission if the pulley is not transferring power to the output shaft
@workshopstudios433 ай бұрын
Thanks for sharing. There is so much great content out there that has helped and encouraged and entertained me. I'm glad to be able to contribute in my small way!!
@plantpoweredhealth93833 ай бұрын
Great video thanks for sharing. Fixed a problem I had exactly as you showed. Cheers!
@workshopstudios433 ай бұрын
So glad it helped!! Thanks for sharing your success!
@jol38863 ай бұрын
Was it not turning the shaft when you turned the pulley wheel before that cuz yeah mine feels stripped too and I'm hoping this fixes it because I ordered one and it was too short even though it's identical
@workshopstudios433 ай бұрын
You may have seen that my mower transmission was seized until I took it out and added some lubrication. So I didn't have to replace anything. I don't think my experience will help with your problem. Thanks for watching and commenting. Good luck with your repair
@jol38863 ай бұрын
@@workshopstudios43 it actually totally worked! thank you!
@liggerstuxin14 ай бұрын
If there is zero sound whatsoever. No clicking from the starter solenoid. Is it still potentially the solenoid?
@workshopstudios433 ай бұрын
It could be. If the solenoid is completely locked up, then the metal pin doesn't move; hence, no click. Hope that helps! Thanks for watching and your great question!
@nja32244 ай бұрын
Half the “fun” is in the tinkering, troubleshooting, figuring out why it’s not working and if it’s worth fixing at all. I had no reason to watch this video other than the rink looks exactly like the one I have or had, and it is. Thoroughly enjoyed watching you go through this journey, thank you for sharing this. I am now a subscriber and look forward to future content.
@workshopstudios433 ай бұрын
Amen to that!! Welcome to the channel 😀 I hope my content will continue to be informative and entertaining!
@nja32244 ай бұрын
A man after my own heart. Fix your own stuff and do it right. Even better for putting this out there for others to see and learn. Well done Sir! 👍
@workshopstudios433 ай бұрын
Wow!! Thanks for the kind words and encouragement!!! I started sharing on KZbin to give back to the community that has been such a help to me.
@nja32243 ай бұрын
@@workshopstudios43 - I’m on it daily for work related content and how to videos. I’ve put a few out myself for the same reasons as you. You’re a good man! 👍
@ninascherry32744 ай бұрын
20 year old healthy maple needs it’s roots grinded or cut. Will the maple live a healthy life after? Answer asap please and thank you..
@workshopstudios434 ай бұрын
Great question! I am not an arborist (tree expert) just a homeowner. The trees roots I cut in the video (and others I have cut) did not effect the trees. I have some experience with removing volunteer silver maples (tree and roots). My experience is that they are very hardy and would tolerate some surface root removal. Hopefully you have a trusted tree expert to help you with the root removal. Thanks for watching and sharing!
@M87RigelAntaresM424 ай бұрын
Thanks Same exact problemwith my 2015 GS350
@workshopstudios434 ай бұрын
Glad it helped! Thanks for sharing your experience!!
@brandonf19894 ай бұрын
Just used your great video to walk my 78 year old Father diagnosing and getting our John Deere lawn mower running 200 miles away. Thank you sir!
@workshopstudios434 ай бұрын
That's awesome!! Thanks so much for sharing your story. And my best to your father
@micheleborowski78284 ай бұрын
What did you use to cut pipe?
@workshopstudios434 ай бұрын
I used a copper tube cutter that is very compact. It allows me to get into tight places. You gave me an idea for a new video on tubing and pipe and how to cut and connect. Thanks!!
@danielleanecito35674 ай бұрын
I just got one just about the same as yours! Needed to see how to attach the mirror and thankful for your video I was able to see
@workshopstudios434 ай бұрын
Glad I could help! And thanks for watching and commenting!! Good luck with your restoration!
@jobgreaves8 күн бұрын
Me too. I see the little triangle wood pieces that hold the mirror in. The old dresser I got had Gorilla tape holding the back on and no little pieces of wood. Thanks, John in Oregon
@user-mz6py1hg6f4 ай бұрын
😮😊
@workshopstudios434 ай бұрын
Thanks for watching!!
@pablopiquante32275 ай бұрын
Thanks for posting! Many people who do not use bleach in their wash just unplug the power to that solenoid. A very low cost solution to a potentially very expensive water damage scenario.
@workshopstudios435 ай бұрын
Great point! Thanks for watching and sharing!!
@cheeseandrice87710 күн бұрын
Thanks for this. Going to try this suggestion and see what happens 🤷♀️
@pablopiquante32275 күн бұрын
@@cheeseandrice877 It worked well for me, did it work for you? I also put electrical tape of any exposed contacts.